beurer MP 52 Manicure Set Instruction Manual

: June 5, 2024
: Beurer

Table of Contents

WARNINGS AND SAFETY NOTES
- Intended use
SIGNS AND SYMBOLS
INCLUDED IN DELIVERY
DEVICE DESCRIPTION
USAGE
- Attachments
CLEANING AND MAINTENANCE
- Risk of electric shock
ACCESSORIES AND REPLACEMENT PARTS
DISPOSAL
TECHNICAL DATA
WARRANTY

Unfold page 3 before reading the instructions for use.

ENGLISH
Read these instructions for use carefully. Observe the warnings and safety notes. Keep these instructions for use for future reference. Make the instructions for use accessible to other users. If the device is passed on, provide the instructions for use to the next user as well.

WARNINGS AND SAFETY NOTES

WARNING

The device must only be used for the purpose for which it was designed and in the manner specified in the instructions for use. Any improper use may be dangerous.
The device is only intended for domestic/private use, not for commercial use.
This device may be used by children over the age of 8 and by people with reduced physical, sensory or mental skills or a lack of experience or knowledge, provided that they are supervised or have been instructed on how to use the device safely, and are fully aware of the consequent risks of use.
Children must not play with the device.
Cleaning and user maintenance must not be performed by children unless supervised.
Do not use the device if it shows signs of damage or does not function properly. In such cases, contact Customer Services.
Repairs must only be carried out by Customer Services or authorised retailers.
Under no circumstances should you open or repair the device yourself, as correct functioning of the device can no longer be guaranteed should you do so. Failure to observe this will invalidate the warranty.
Check the results regularly during the treatment. It is particularly important for diabetics to do so as they have a lower sensitivity to pain and could injure themselves more easily. In principle, the attachments that are supplied with the device are suitable for diabetics. However, please use with particular care and do not use at high speed. If you have any doubts, consult your doctor.
The device may heat up faster during prolonged, intensive use, for example when removing calluses on the feet. Allow the device to cool down for a relatively long time between individual applications to prevent skin burns. For your own safety, continuously check the heat generated by the device. This applies in particular to persons that are not as sensitive to heat as others.
The manufacturer is not liable for damage resulting from improper or incorrect use.
Keep packaging material away from children. There is a risk of suffocation.
In the event of defects and operational faults, switch off the device immediately.
Only use the device with the supplied accessories.
Do not use on animals.
Do not allow the device to come into contact with water (except in the case of cleaning with a slightly damp cloth). Water must never enter inside the device. Never submerge the device in water. Never use the device in the bath, in the shower, in a swimming pool or above a sink filled with water. If water enters the housing of the device nevertheless, immediately disconnect the device from the mains supply and contact your electronics retailer or Customer Services.
Make sure that no hair can get caught in the rotating attachments when using the device. Use a hair tie for your safety.
Hands must always be dry when using the device and mains adapter plug.
Wear appropriate protective equipment (FFP2 mask, protective gloves and protective glasses) when using on acrylic, gel or artificial nails.

Intended use

This device is intended for the treatment of hands (manicure) and feet (pedicure) only.

NOTE

Keep the device away from sources of heat.
Never use the device under a blanket, pillow or cushion, etc.

SIGNS AND SYMBOLS

The following symbols are used on the device, in these instructions for use, on the packaging and on the type plate for the device:

| Read the instructions
---|---
WARNING| Indicates a potentially imminent danger. If it is not avoided, there is a risk of death or serious injury.
CAUTION| Indicates a potentially imminent danger. If it is not avoided, slight or minor injuries may result.
NOTE| Indicates a potentially harmful situation. If it is not avoided, the system or something in its vicinity may be damaged.
| CE labeling

This product satisfies the requirements of the applicable European and national directives.

| Manufacturer
| Disposal in accordance with the Waste Electrical and Electronic Equipment EC Directive – WEEE
| Separate the packaging elements and dispose of them in accordance with local regulations
| Marking to identify the packaging material.

A = Material code, B = Material number:

1-7 = Plastics, 20-22 = Paper and cardboard

| The products demonstrably meet the requirements of the Technical Regulations of the EAEU
| Product information Important information to note
| United Kingdom Conformity Assessed Mark
| Polarity of DC power connection
| Direct current
The device is suitable for use with direct current only
| Protection class II device
The device is double-insulated and is, therefore, in protection class 2
| Energy efficiency level 6
| For indoor use only
| Safety isolating transformer, short-circuit proof
| Switching mains adapter
| Separate the product and packaging elements and dispose of them in accordance with local regulations.

INCLUDED IN DELIVERY

Check that the device packaging has not been tampered with and make sure that all contents are present. Before use, ensure that there is no visible damage to the device or accessories and that all packaging material has been removed. If you have any doubts, do not use the device and contact your retailer or the specified Customer Services address.

1 manicure set
7 high-quality attachments made from sapphire and felt
10 single-use attachments made from sandpaper
1 USB-C cable with mains adapter
1 storage bag
1 instructions for use

DEVICE DESCRIPTION

The corresponding drawings are shown on page 3.

Manicure/pedicure device
ON/OFF button
+/- speed regulation
LED status display
Blue = ready for use
Red = anti-clockwise rotation
Green = clockwise rotation
USB-C connection
Sapphire wheel, fine
Sapphire cone, fine
Sapphire cone, coarse
Felt cone
Attachment for using the sandpaper attachments
Single-use attachments made of sandpaper
Flame-shape cutter
Sapphire cutter, round

USAGE

Connect the USB-C connection ( 5) to the supplied USB-C cable and the mains adapter.
Continuous blue illumination of the LED status display ( 4) means that the device is ready for operation. Before using the device, please do not carry out pre-treatment in a water bath, as the callus attachments are less effective on soaked or wet skin.
Make sure that the device is switched off.
Select the desired attachment part and carefully press it onto the axle of the device. To remove, pull apart the attachment and the device in opposing directions.
Switch the device on by pressing the ON/OFF button ( 2 ) . You can change the direction of rotation by briefly pressing the ON/OFF button ( 2 ) again (anti-clockwise rotation red / clockwise rotation green). If you press and hold the ON/OFF button ( 2 ) , the device switches off.
You can select the speed of the drive axle using the plus (+) and minus (-) speed regulation buttons ( 3) . Start each application at a low speed and then increase as required.
Do not press too hard and always carefully move the attachments towards the area to be treated. Move the device over the area to be treated and apply slight pressure while slowly moving the device in circles.
When filing, always move from the outside of the nail towards the tip. Check the results regularly during the treatment. Stop treatment as soon as it becomes unpleasant. Do not remove the entire callus to maintain natural skin protection.
Ensure the axle can always rotate freely. If the axle is blocked for approx. ( 3) seconds, the device switches off to protect the motor. To indicate that the motor protection has been activated, the LED status display ( 4) flashes blue. The device then switches to standby mode and the LED status display ( 4) lights up permanently in blue.
Apply moisturizer to the treated areas after each use.
The device switches off automatically after 20 minutes

Attachments

Sapphire wheel, fine (6)

Suitable for filing and treating nails, fine-grain sapphire wheel. The special feature of this sapphire wheel is that the internal sanding disc rotates whereas the external housing does not. This makes it possible to file nails precisely without the risk of burning the skin with the quickly rotating wheel.

Sapphire cone, fine (7)

Suitable for removing dry skin, calluses on the sole of the foot and heel, and treating the nails. Do not remove the entire callus to maintain natural skin protection.

Sapphire cone, coarse (8)

Suitable to quickly remove hard skin and large calluses on the sole of the foot and heel. This attachment is intended for application on large areas. Do not remove the entire callus to maintain natural skin protection.

Felt cone (9)

Suitable for smoothing and buffing the tips of nails after filing and for cleaning the surface of nails. Always use circular movements to buff the nails and never let the felt cone rest in one position as the friction can create a considerable amount of heat.

Attachment for using the sandpaper attachments (10)

Suitable for fitting sandpaper attachments.

Single-use attachments made of sandpaper (11)

Suitable for removing dry skin, calluses on the sole of the foot and heel, and treating the nails. The special feature of the single-use sandpaper attachments is that they can be removed and disposed of after a single use. Do not remove the entire callus to maintain natural skin protection.

Flame-shape cutter (12)

Suitable for removing ingrown nails. For this purpose, carefully position the flame-shape cutter on the area to be treated and remove the necessary nail parts.

Sapphire cutter, round (13)

Suitable for carefully removing corns. If you are using this attachment, please keep in mind that you may penetrate deeper into the skin when removing the skin layers of the corn, therefore damaging the periosteum.

CLEANING AND MAINTENANCE

WARNING

Risk of electric shock

Unplug the device each time before cleaning. Clean the device using only the method specified. Never immerse the device or the USB-C charging cable with mains adapter in water or other liquids.

Do not use any chemical or abrasive cleaning agents.
Clean the device with a slightly damp cloth. If it is very dirty, you can also moisten the cloth with a mild soapy solution.
For hygienic reasons, the attachments can be cleaned with a cloth moistened with alcohol.

ACCESSORIES AND REPLACEMENT PARTS

To purchase accessories and replacement parts, please visit www.beurer.com or contact the service address for your country (see the service address list). Accessories and replacement parts are also available from retailers.

Designation	Item number and/or order number

Attachment set
(includes the following attachments)1 sapphire wheel, fine1 sapphire cone, fine

1 sapphire cone, coarse

1 felt cone

10 single-use attachments made from sandpaper

1 flame-shape cutter

1 sapphire cutter, round

|

572.17

DISPOSAL

For environmental reasons, do not dispose of the device in household waste at the end of its service life. Dispose of the device at a suitable local collection or recycling point in your country. Observe the local regulations for material disposal. Dispose of the device in accordance with EC Directive – WEEE (Waste Electrical and Electronic Equipment).
If you have any questions, please contact the local authorities responsible for waste disposal.
You can obtain the location of collection points for old devices from the local or municipal authorities, local waste disposal companies or your retailer, for example.

TECHNICAL DATA

Power supply| Input: 100-240 V ~ 50/60 Hz; 0.5 A max

Output: 5.0 V 2.0 A; 10.0 W

---|---
Dimensions (L x W x H)| 142 x 21 x 18 mm
Weight| Approx. 52.5 g
Average efficiency during operation| ≥ 81.57%
No-load power consumption| ≤ 0.06 W

Subject to technical changes.

The Declaration of Conformity for this product can be found at the
following address:
https://www.beurer.com/web/we-landingpages/de/cedeclarationofconformity.php