Skullcandy Dime 2 True Wireless Earbuds User Guide
- June 5, 2024
- Skullcandy
Table of Contents
Skullcandy Dime 2 True Wireless Earbuds
Charge Earbuds
Power-Off
Left Side or Right Side
Barcode
Scan to get started. Warranty information at: skullcandy.com/waranty
Charge Case
Play/Pause
Left Side or Right Side
Auto Pair Mode
Pairing Mode
Pairing Mode
Left Side or Right Side Off Mode
Track Forward
Right Side
Auto Power- On
Pair New Device
“Dime 2”
TrackBack
Left Side
Auto Power- Off
Power- On
Left Side or Right Side
Volume Up
Right Side
Volume Down
Left Side
Re-Sync Earbuds
Both Earbuds
- While On
- Bluetooth Disconnected
Answer/End
Left Side or Right Side
Activate Voice Assistant
Left Side or Right Side
Clear Paired Device
Left OR Right Side
- Both Buds Powered ON
- Not Connected to Device
Find With Tile
Both Earbuds
- Tile App Required
Features
- Speaker Driver: 6mm,
- Impedance: 16 Ohms, THD <3%@1KHz,
- Voltage Regulation: 5V=015A, Bluetooth 5.2,
- Frequency Band: 2402MHz-248OMHz,
- Maximum Power: 9.64dlBm,
- Weight: 32g.
CAUTION
Risk of explosion if the battery is replaced by incorrect type disposal of a
battery into fire or a hot oven, or mechanically crushing or cutting of a
battery, that can result in an explosion; leaving a battery in an extremely
high temperature surrounding environment that can result in an explosion or
the leakage of flammable liquid or gas; a battery subjected to the extremely
low air pressure that may result in an explosion or the leakage of flammable
liquid or gas.
Hardware Version:
WS20 RXLREV: E2 TWS20 RX_R_REV: F DIME2 REV: A (Charging Case)
Software Version:
V1.1.3.9 (earbuds) 2021 Skullcandy, Inc. Skullcandy.com/patent-
information Dime 2
MODEL: S2DBW S2DBWL
FCC ID: Y22-S2DBW
IC: 10486A-S2DBW
1 Year Global Limited Warranty
The United States of America and Canada Product Purchases Only Skullcandy products are backed by a 1-year limited warranty. If it doesn’t work the way we promised, we’ll make it right. For Guarantee Claims, Questions and Terms & Conditions visit www.skullcandy.com/warranty or call us at 1-888-MY SKULL
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Contains a Li-ion battery. The battery must be recycled or disposed of properly.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
ISED Compliance Statement
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Visit: www.skullcandy.com
ISED SAR Compliance Statement
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. The end-user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value is reported under this standard during product certification for use when properly worn on the head.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>