Lenco MES-212 Portable DVD Player User Manual

: June 3, 2024
: Lenco

Table of Contents

Safety Instructions
Identification of Controls
SETUP Menu Setting
Parameters and specifications
Guarantee
Disclaimer
Disposal of the Old Device
CE Marking
Service
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Lenco MES-212 Portable DVD Player User Manual

Safety Instructions

Before using this product, read and follow all warnings and instructions.
This device is not intended for use by people (including children) with physical, sensory or mental disabilities, or a lack of experience and knowledge, unless they’re under supervision or have received instructions about the correct use of the device by the person who is responsible for their safety;
This product is intended for household use only and not for commercial or industrial use.
Do not expose to dripping or splashing.
No naked flame sources, such as lighted candles, should be placed on or near the product.
Ventilation should not be impeded by covering ventilation openings with items such as newspapers, table cloths, curtains and the like.
Make sure the unit is adjusted to a stable position. Damage caused by using this product in an unstable position or by failure to follow any other warning or precaution contained within this user manual will not be covered by warranty.
Do not place objects filled with liquids, such as vases on or near the product.
Do not use or store this product in a place where it is subject to direct sunlight, heat, excessive dust or vibration.
Do not keep or store this product in wet conditions for a long period.
Do not clean this product with water or other liquids.
Do not block or cover the slots and holes in the product.
Do not push foreign objects into the slots or holes in the product.
Do not attempt to open this product yourself. There are no user serviceable parts inside.
Do not allow children access to plastic bags.

Notice

If at any time in the future you should need to dispose of this product please note that: All batteries and accumulators need to be removed from this product (Removal of Waste Batteries and Accumulators).
Always bring your product to a professional to remove the built-in battery.

WARNING

Do not ingest the battery, Chemical Burn Hazard
(The remote control supplied with) This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Warning

Never remove the casing of this device.
Never place this device on other electrical equipment.

To prevent possible hearing damage, do not listen at high volume levels for long periods.

Mounting in the Vehicle

Use the supplied car mounting straps to install the main unit and monitor on the back of the vehicle’s headrests. Tightly wrap the mounting strap around the headrest.

Identification of Controls

Main Unit
Identification of Controls

SETUP
Up/Prev
Down/Next
ENTER
/VOL- Left/VOL
/VOL+ Right/VOL+
SOURCE
ON/OFF
USB
Earphone Socket
AV OUT
DC OUT
DC IN 9-12V
MUTE
UP
Down
/VOL- Left/VOL
/VOL+ Right/VOL+
MODE
BACK LIGHT
DC IN 9-12V
AV IN
Earphone Socket
ON/OFF
POWER INDICATOR

Remote control unit
Identification of Controls

SOURCE
DVD/USB.
MUTE
Disable Audio output.
0-9 NUMBER BUTTON
Selects numbered items in a menu.
DISPLAY
To display the playtime and status information.
10+ BUTTON
In order to select a track 10, for CD, press 10+ button first, then press 0; for DVD, press 10+ button; select track greater than 10, for example, track 12; first press 10+, a highlighted bar appears and further press 10+ and press number 2; select track 23, press 10+ button 3 times and press number 3 button.
MENU/PBC
Return to DVD root menu(DVD).
PBC on/off switch (VCD).
AUDIO
DVD: Press AUDIO repeatedly during playback to hear a different audio language or audio track, if available.
CD/VCD: Press AUDIO repeatedly during playback to hear a different audio channel (Left, Right, Mix, Stereo).
PLAY/PAUSE
Press PLAY/PAUSE once to pause playback, pressing PLAY/PAUSE a second time will resume the playback.
STOP
When this button is pressed once, the unit records the stopped point, from where playback will resume if PLAY ( )is pressed after wards. But if STOP button is pressed again instead of PLAY ( ) button, there will be no resume function.
MODE
Set LCD parameter (adjust brightness, contrast, and saturation).
VOL+
Adjust volume
Forward Skip
Go to next chapter/track.
Reverse Skip
Go to previous chapter/track to the beginning.
BUTTON
Press BUTTON allow skipping ahead at 5-level speed (X2->X4->X8->X16->X32->PLAY), press PLAY button return to normal playback
BUTTON
Press BUTTON allows skipping back at 5-level speed(X2->X4->X8->X16->X32->PLAY), press
PLAY button return to normal playback.
STEP
Step the motion in DVD mode.
SEARCH
Go to time point, title or chapter you want in DVD Mode.
SUBTITLE
Press SUBTITLE repeatedly during playback to hear a different subtitle languages.
ANGLE
DVD: Press ANGLE will change the view angle, on DVDs that support this feature.
TITLE
Return to DVD title menu
ENTER
Confirms menu selection..
SETUP
Accesses or removes setup menu.
VOLAdjust volume
REPEAT
Press REPEAT during playback to select a desired repeat mode.
DVD: you can play select repeat chapter/title/off.
CD/VCD: you can select repeat single/all/off.
Mp3: you can select shuffle/random/single/repeat one/repeat folder/folder
SLOW
Press Slow button repeatedly to enter slow playback, and cycle between different speeds. The speeds are 1/2, 1/4, 1/8, 1/16, and normal.
PROGRAM
DVD/VCD: The program function enables you to store your favorite tracks from the disc. Press the PROGRAM button, then the PROGRAM MENU will appear on screen, now you can use the number key to direct input the titles, chapters or tracks number and select PLAY option. to resume normal playback, press PROGRAM and select clear program option on the program menu, press PROGRAM again to exit the program menu.
ZOOM
DVD/VCD: Use ZOOM to enlarge or shrink the video image.
- Press ZOOM during playback or still playback to activate the Zoom function. The square frame appears briefly in the right bottom of the picture.
- Each press of the ZOOM button changes the TV screen in the following sequence:
  2X size 3X size 4X size 1/2X size 1/3X size 1/4X size normal size JPEG: Use ZOOM to enlarge or shrink the picture.
  Press ‘ZOOM’.
- Use “ ” to enlarge, or “ ” to shorten the picture.
- Use the button to move through the zoomed picture.

General Setup Page

Press the SETUP button to get the setup menu. Use the direction buttons to select the preferred item. After finishing settings, press SETUP again to normally display.
The following menu items can be changed:
GENERAL: selects the GENERAL PAGE menu.
AUDIO: selects the AUDIO PAGE menu.
VIDEO: selects the VIDEO PAGE menu.
PREFERENCE: selects the PREFERENCE PAGE menu.
General Setup Page

TV DISPLAY: selects the aspect ratio of the playback picture.
4:3 PANSCAN: if you have a normal TV and want both sides of the picture to be trimmed or formatted to fit your TV screen.
4:3 LETTERBOX: if you have a normal TV. In this case, a wide picture with black bands on the upper and lower portions of the TV screen will be displayed.
16:9: wide screen display.
TFT Display
Angle Mark
Displays current angle setting information on the right hand corner of the TFT screen if available on the disc.
OSD Language
You can select your own preferred language settings.

Closed Captions
Closed captions are data that are hidden in the video signal of some discs. Before you select this function, please ensure that the disc contains closed captions information and your TV set also has this function.

Screen Saver
This function is used to turn the screen saver On or Off

Auto Standby
This function is used to select auto standby settings after 3 or 4 hours.
3 HOURS: the unit will turn to standby mode after 3 hours if there is no interaction from the user within this period of time.
4 HOURS: the unit will turn to standby mode after 4 hours if there is no interaction from the user within this period of time.
OFF: the auto standby function is disabled, and the unit will stay in the “on” mode even if there is no interaction from user..
Audio Setup Page
Audio Setup Page

Video Setup Page

Downmix
This options allows you to set the stereo analog output of your DVD Player.
LT/RT: Select this option if your DVD Player is connected to a Dolby Pro Logic decoder.
Stereo: Select this option when the output delivers sound from the two front speakers only.

Dolby digital
The options included in Dolby Digital Setup are: ‘Dual Mono’ and ‘Dynamic’. Dual Mono
Stereo: Left mono sound will send output signals to the Left speaker and the Right mono sound will send output signals to the Right speaker.

L-Mono: Left mono sound will send output signals to Left speaker and the Right speaker.
R-Mono: Right mono sound will send output signals to the Left speaker and the Right speaker.
Mix-Mono: Left and Right mixed mono sound will send output signals to the Left and Right speakers.

Dynamic
Dynamic range compression.
Video Setup Page
VIDEO SETUP PAGE

Brightness, Contrast, Hue, Saturation: setting the video quality.

Preference Page
Preference Page

TV Type
Selecting the colour system that corresponds to your TV when AV outputs. This DVD Player is
compatible with both NTSC and PAL.

Preference Page
PAL – Select this if the connected TV is a PAL system. It will change the video signal of a NTSC disc and output in PAL format.
NTSC -Select this if the connected TV is NTSC system. It will change the video signal of a PAL disc and output in NTSC format.
Auto: Changes the video signal output automatically according to the playing disk format.
Audio: Selects a language for audio (if available).
Subtitle: Selects a language for subtitle (if available).
Disc Menu: Selects a language for disc menu (if available).

Default: Back to the factory settings.
Second display mode

Bright
Adjust screen Bright Setting.
Contrast
Adjust screen Contrast Setting.
Colour
Adjust screen Color Setting.
LANG
Adjust Menu OSD Language
ZOOM
Adjust screen 16:9 or 4:3
RESET
Reset to default setting.

Parameters and specifications

Electronical parameters

Item	Standard requirement
Power consumption	: <10W
Operating humidity	: 5% to 90%
Output	VIDEO OUT
AUDIO OUT	: 1.2 Vrms (1 KHz, 0 dB)
Audio	:Speaker: 1WX2, Headphones output

System

Laser	:Semiconductor laser, wavelength 650 nm
Signal system	:NTSC/PAL
Frequency response	: 20Hz to 20 kHz(1 dB)
Signal-to-noise ratio	:More than 80 dB (ANALOG OUT connectors only)
Dynamic range	:More than 85 dB (DVD/CD)

Note: Design and specifications are subject to change prior notice.

Guarantee

Lenco offers service and warranty in accordance with the European law, which means that in case of repairs (both during and after the warranty period) you should contact your local dealer.
Important note: It is not possible to send products that need repairs to Lenco directly.
Important note: If this unit is opened or accessed by a non-official service center in any way, the warranty expires.
This device is not suitable for professional use. In case of professional use, all warranty obligations of the manufacturer will be voided.

Disclaimer

Updates to Firmware and/or hardware components are made regularly. Therefore some of the instruction, specifications and pictures in this documentation may differ slightly from your particular situation. All items described in this guide for illustration purposes only and may not apply to particular situation. No legal right or entitlements may be obtained from the description made in this manual.

Disposal of the Old Device

This symbol indicates that the relevant electrical product or battery should not be disposed of as general household waste in Europe. To ensure the correct waste treatment of the product and battery, please dispose them in accordance to any applicable local laws of requirement for disposal of electrical equipment or batteries.
In so doing, you will help to conserve natural resources and improve standards of environmental protection in treatment and disposal of electrical waste (Waste Electrical and Electronic Equipment Directive).

CE Marking

Products with the CE marking comply with the EMC Directive (2014/30/EU) and the Low Voltage Directive (2014/35/EU) issued by the Commission of the European Community.

Hereby, Lenco Benelux BV, Thermiekstraat 1a, 6361 HB Nuth, The Netherlands, declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

The declaration of conformity may be consulted via techdoc@lenco.com