cecotec B08YF8P8F9 Fast and Furious 8010 Vital Ironing Station Instruction Manual

cecotec B08YF8P8F9 Fast and Furious 8010 Vital Ironing Station

SAFETY INSTRUCTIONS

Read these instructions thoroughly before using the appliance. Keep this instruction manual for future reference or new users. Make sure that the mains voltage matches the voltage stated on the rating label of the appliance and that the wall outlet is grounded.
Do not immerse the cord, plug, or any non-removable part of the appliance in water or any other liquid, nor expose the electrical connections to water. Make sure your hands are dry before handling the plug or switching on the appliance.
If the appliance falls accidentally in water, unplug it immediately. Do not reach into the water!
Do not twist, bend, strain, or damage the power cord in any way. Protect it from sharp edges and heat sources. Do not let it touch hot surfaces. Do not let the cord hang over the edge of the surface.
This appliance is not intended to be operated by means of an external timer or separate remote-control system.
Turn off and unplug the appliance from the mains supply when not in use and before cleaning it. Pull from the plug, not the cord, to disconnect it from the outlet.
This appliance is designed to iron textiles. It is designed for domestic use only and, therefore, not suitable for commercial use. Do not use outdoors.
To protect against burns or injuries to persons, do not iron textiles while being worn on the body.
Do not use any accessory that has not been recommended by Cecotec, as they might cause injuries or damage.
The appliance is not intended to be used by children under the age of 8. It can be used by children over the age of 8, as long as they are given continuous supervision.
This product can be used by children and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge, as long as they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Close supervision is necessary when the appliance is being used by or near children. Keep this appliance and its power cord out of reach of children under the age of 8.
Place the appliance on a dry, stable, flat, heat-resistant surface. The temperature of accessible surfaces may be high while in use and could cause burns. Do not touch hot surfaces while in use or immediately after.
Unplug the appliance immediately if fire or smoke is observed.

Do not leave the product unsupervised during  operation. Unplug the device after use and when you leave the room where it is installed.
The appliance must not be plugged in when filling or emptying the water tank.
The tank cap must not be open when the appliance is switched on.
The use of tap water is recommended. If the lime content of the tap water is too high, use a mix composed of 50 % of tap water and 50 % of water with low mineral content. Do not use only water with low mineral content.
Burns can occur when touching hot metal parts, hot water, or steam. Hot water may leak from the iron. Be careful when filling or turning the steam iron upside down.
To protect against burns or injuries, do not direct steam toward persons or animals when ironing.
The iron must be used and placed on a stable surface. When placing the iron on its stand, make sure that the surface is stable.
Keeping the iron at maximum temperature for too long may cause discoloration, which will not affect the performance of the appliance.
Do not try to repair the device by yourself. Contact the official Technical Support Service of Cerotic for advice.
Cleaning and maintenance must be carried out according to this instruction manual to make sure the appliance functions properly. Turn off and unplug the appliance before moving and cleaning it. Make sure the iron has completely cooled down before storing it.
Cleaning and maintenance tasks must not be carried out by children.
Store the appliance and its instruction manual in a safe and dry place when not in use.
Cerotic takes no responsibility for any damage caused by misuse of the appliance. Any misuse or noncompliance with these instructions renders the warranty and Cicotte’s liability null and void.
If the cord is damaged, it must be replaced by the official Technical Support Service of Cerotic in order to avoid any type of danger.
Warning: All our ironing range’s products have undergone quality control tests previous to their commercialization. These tests consist of filling the water tank in order to check tightness and to ensure correct operating of the device. Once the test has been carried out, the tank is emptied and dried, but there is a slight probability that water could remain inside it.

PARTS AND COMPONENTS

Steam station
Fig. 1.

1. Steam toggle button
2. Clean button
3. Water spray button
4. Function indicator
5. Spray nozzle
6. Soleplate
7. Water inlet cover
8. Water tank
9. Cord winding groove
10. Unit base
11. Thermal insulation stand
12. Temperature knob
13. Temperature indicator
14. Handle
15. Steam trigger

Temperature knob
Fig. 2.

1. 170 ºC-225 ºC (Maximum)
2. 140 ºC-210 ºC
3. 100 ºC-160 ºC
4. 70 ºC-120 ºC (Minimum)

Buttons and light indicators
Fig. 3.

1. Eco steam rate indicator
2. Clean indicator
3. Max. steam rate indicator
4. Water spray button
5. Steam toggle button
6. Clean button

BEFORE USE

Take the product out of the box.
Remove packaging material, stickers and labels from the soleplate.
Clean the iron’s soleplate with a soft cloth.
Fill the water tank with water and heat up the iron. Then, iron over a piece of damp cloth for several minutes for the purpose of removing any residue on the soleplate.
Note: You may notice a slight burning smell or smoke when using the appliance for the
first time, caused by the excess of lubricants from the manufacturing process. Smoke will disappear after a short time.

OPERATION

Water inlet cover
Open the water inlet cover and fill the water tank with water through the filling aperture. Make sure the water does not exceed the MAX. mark on water tank.

Steam toggle button
The appliance can switch from MAX to ECO steam rates by pressing the steam toggle button. The default setting is the MAX steam rate when the appliance is turned on. Press the steam toggle button to select your desired steam rate. The corresponding indicator of the selected steam rate will light up.

Temperature knob
Turn the temperature knob to set the desired ironing temperature based on the garment to be ironed. To activate the steam function, select the appropriate temperature to produce steam. Otherwise, steam will not be emitted efficiently.

Temperature indicator
When the iron is heating up, the temperature indicator will turn on. Once the iron has reached the selected temperature, it will turn off. The temperature indicator will switch on and off as the iron maintains the selected temperature during ironing.

Steam trigger
When the appliance is heated to the selected temperature, press the steam trigger for steam to be sprayed from the soleplate continuously. Release the steam trigger to use the device for dry ironing without steam.

Steam burst
Fig. 4. Quickly press the steam trigger twice to produce a burst of steam, and the indicator of MAX steam rate will blink. The steam burst function can be only activated when the appliance is  operated under MAX steam rate and the indicator of MAX steam rate is turned steady on.

Water spray button
Press the water spray button to activate the water spray function. The spray nozzle will spray water mist. Release the water spray button to stop the function.

Clean indicator
The appliance needs to be cleaned when the clean indicator lights up and remains on. It will blink when the appliance is being cleaned.

Clean button
Before activating the clean function, make sure the temperature knob is turned to the Max. setting and that the device is set to the steam mode. Press the steam trigger once for the water spray button to return to its original position.
The appliance must be cleaned when the clean indicator turns steady on. Before cleaning, prepare a container with a capacity of more than 300 ml for collecting the waste water. Hold and press the “Clean button” for 2 seconds. When the buzzer sounds, the appliance will enter into the cleaning mode and the clean indicator will blink. The cleaning process will last for 3 minutes.
The clean indicator will turn off. If another cleaning cycle is required, hold down the clean button for 5 seconds. When the buzzer sounds, the appliance will enter into the cleaning mode and the clean indicator will blink. The cleaning process will last for 3 minutes.

Cord winding groove
When not in use, the steam supply hose and power cord can be wound along the cord winding groove for storage.
Fig. 5. Note: The appliance will shut off automatically if all the indicators start blinking after being powered on, indicating the appliance has malfunctioned. Stop using the appliance and contact the Technical Support Service of Cerotic if this happens.

Dry ironing
Place the iron on the thermal insulation stand of the unit base.
Plug the power cord into the outlet. The temperature indicator and the indicator of MAX. steam rate will turn on.
Turn the temperature knob to select the desired temperature setting depending on the garment’s fabric. The iron wills start heating up.
The light indicator will turn off when the desired temperature has been reached. Once it has turned off, the iron is ready to use.
Warning: Always allow the device and especially its soleplate to cool completely down before touching or handling it.

Steam ironing
Recommendation: To lengthen the appliance’s service life, use purified water.
Place the unit base on a stable, flat surface.
Open the water inlet cover, fill the water tank with water through the filling opening. Do not exceed the MAX mark on the tank: 2L.
Place the iron on the thermal insulation stand of the unit base.
Plug the power cord into the outlet. Turn the temperature knob, the MAX. steam rate indicator will turn on by default. Choose between MAX and ECO steam rate, select the desired steam rate for each garment according to your requirement. Ensure there is enough water in the tank. Turn the temperature knob to select the desired temperature setting depending on the garment’s fabric. The iron wills start heating up.

Ironing tips
Always check if the garment to be steamed has a label with instructions for ironing, and if it has, follow the instructions.
If the fabric consists of various kinds of fibers, always select the lowest ironing temperature. Synthetic fibre and silk fabrics should be ironed on their inner side to avoid them from being damaged.
Velvet and other textures that rapidly become shiny should be ironed in one direction with light pressure applied. Always keep the iron moving.
Pure wool fabrics (100% wool) may be ironed with the steam iron. Use a dry cloth as a mat and then select the corresponding fabric setting for ironing.
Never iron over zip, rivet in the cloth, this will damage the soleplate.
Before activating the clean function, make sure that the water in the tank is sufficient, and prepare a high temperature-resistant container to be placed under the soleplate for holding the dirty water sprayed from the steam hole of the soleplate during cleaning.
After a few minutes, the temperature indicator will turn off indicating the soleplate has reached the selected temperature and the iron is ready to use with steam.
Press the steam trigger to activate steam ironing. Release it to stop.
Note: Water may drip during spraying steam function when the temperature is set at the low settings.

Warnings:
Do not activate the steam button when the iron is placed on the unit base to avoid being calved by steam.
After ironing, remove the plug from the wall socket. The appliance will turn off and all the indicators will turn off too. Allow the whole unit to cool completely down before holding or storing it

CLEANING AND MAINTENANCE

• Turn off, unplug the appliance from the power supply, empty the water tank (do it after each use) and allow it to cool down completely.
• Use a soft, damp cloth to clean the device’s surface.
• In case fabric is adhered to the soleplate due to heat, use a damp cloth and vinegar to detach it. Do not use abrasive cleaners or scouring pads to clean the product.
• If scale blocks the steam holes, use a toothpick to remove it.
• If the appliance is not going to be used for a long time, pour out the water in the tank and store the iron on the thermal insulating cushion.
• When not in use, the steam supply hose and power cord must be folded well and stored in their storage compartment.

TECHNICAL SPECIFICATIONS

• 05532 Fast & Furious 8010 Vital
• 2000-2400 W, 220-240 V~, 50-60 Hz, IP XO
• 05533 Fast& Furious 8020 Force
• 2260-2700 W, 20-240 V~, 50-60 Hz, IP XO
• 05534 Fast& Furious 8030 Ultimate
• 2260-2700 W, 220-240 V~, 50-60 Hz, IP XO
• Made in China | Designed in Spain

DISPOSAL OF OLD ELECTRICAL APPLIANCES

The European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), specifies that old household electrical appliances must not be disposed of with the normal unsorted municipal waste. Old appliances must be collected separately, in order to optimize the recovery and recycling of the materials they contain, and reduce the impact on human health and the environment.

The crossed out “wheeled bin” symbol on the product reminds you of your obligation to dispose of the appliance correctly.
Consumers must contact their local authorities or retailer for information concerning the correct disposal of old appliances and/or their batteries.

TECHNICAL SUPPORT AND WARRANTY

This product is under warranty for 2 years from the date of purchase, as long as the proof of purchase is submitted, the product is in perfect physical condition, and it has been given proper use, as explained in this instruction manual.
The warranty will not cover the following situations:
The product has been used for purposes other than those intended for it, misused, beaten, exposed to moisture, immersed in liquid or corrosive substances, as well as any other fault attributable to the customer.
The product has been disassembled, modified, or repaired by persons, not authorised by the official Technical Support Service of Cecotec.
Faults deriving from the normal wear and tear of its parts, due to use.
The warranty service covers every manufacturing defects of your appliance for 2 years, based on current legislation, except consumable parts. In the event of misuse, the warranty will not apply.
If at any moment you detect any problem with your product or have any doubt, do not hesitate to contact Cecotec Technical Support Service at +34 963 210 728.

References

• SmartGroup

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>