LIGHTWARE MMX4x2-HDMI MMX4x2-HT200 Matrix Switcher User Guide
- June 5, 2024
- LIGHTWARE
Table of Contents
- LIGHTWARE MMX4x2-HDMI MMX4x2-HT200 Matrix Switcher
- Important Safety Instructions
- Box Contents
- Types of IR connectors (1/8” TRS / TS)
- Front View
- Mounting
- Rear View – MMX4x2-HT200
- Rear View – MMX4x2-HDMI
- Compact Size Matrix Concept
- Connecting Steps
- Front Panel Operation
- Typical Application
- Maximum Extension Distances for MMX4x2-HT200
- Wiring Guide for RS-232 Data Transmission
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
- 1: Copy HDMI OUT 1 audio to HDMI OUT 2 and AUDIO OUT.
- 2: Copy HDMI OUT 2 audio to HDMI OUT 1 and AUDIO OUT.
- 3: Use audio from Analog Input on all outputs.
- 4: Keep Original Audio on HDMI outputs, de-embed from HDMI OUT 2 to Analog Audio Output.
LIGHTWARE MMX4x2-HDMI MMX4x2-HT200 Matrix Switcher
Important Safety Instructions
Please read the supplied safety instruction document before using the product
and keep it available for future reference.
Introduction
Thank You for choosing Lightware MMX4x2 series device. The product is a
uniquely mini size matrix switcher with additional Lightware developments.
Audio can be de-embedded from the HDMI signal to a balanced 5-pole Phoenix
(Euroblock) port and external audio signal can be embedded into the HDMI
stream from another 5-pole Phoenix input port. The device has a built-in Event
Manager configurable via the Lightware Device Controller software. Further
control options are served by the USB, RS-232, IR (in and out) and Ethernet
ports.
HDBaseTTM and the HDBaseT Alliance logo are trademarks of the HDBaseT
Alliance.
Compatible Devices
MMX4x2-HT200 matrix is compatible with other Lightware TPS devices, matrix TPS
and TPS2 boards, 25G boards, as well as third-party HDBaseT-extenders, but not
compatible with the phased out TPS-90 extenders.
Box Contents
Types of IR connectors (1/8” TRS / TS)
Front View
- Audio input port: 5-pole Phoenix connector for balanced analog audio.
- Infrared connectors: 2 x 3.5mm jack (TS/TRS) connectors for Infrared units (IR IN for the detector, IR OUT for the emitter)
- USB connector: USB interface for LDC connection to control and configure the device.
- RS-232 connector: 3-pole Phoenix connector for serial communication.
- Ethernet connector: RJ45 connector for control and firmware upgrade purpose.
- Status LEDs: LEDs give feedback about current status of the unit.
- Video select button for Output 1: Pushing the button selects video source for Output 1.
- Input select LEDs: LEDs give feedback about current crosspoint settings.
- Video select button for Output 2: Pushing the button selects video source for Output 2.
- Reset button: Pushing the button reboots the unit.
- Set Audio Config button: Audio configuration selector and special function button.
Front Panel LEDs LIVE
- OFF: device is not powered.
- BLINKING (slow; 1 sec): device is powered and operational.
- BLINKING (fast; 0,5 sec): device is in bootload mode.
- ON: device is powered but not operational.
AUDIO OUT
- OFF: embedded audio is not present or muted.
- BLINKING: embedded audio format is not supported for audio de-embedding.
- ON: embedded audio is present and de-embedded.
OUT 1 AUTO
- ON: Autoselect is enabled on HDMI Output 1.
OUT 2 AUTO
- ON: Autoselect is enabled on HDMI Output 2.
Crosspoint Status LEDs (OUT 1 and OUT 2)
- ON (green): input is selected, signal is present.
- BLINKING (green): input is selected, signal is not present.
- BLINKING (amber): Audio configuration #1..4 is selected, see details in Front Panel Operation section.
Mounting
To mount the matrix Lightware supplies optional accessories for different usage. There are two kinds of mounting kits with similar fixing method. The matrix switcher has two mounting holes with inner thread on the bottom side. Fasten the device by the screws enclosed to the accessory.
Under-desk double mounting kit 1U high rack shelf The Under-desk double mounting kit makes easy to mount a single device on any flat surface, e.g. furniture. 1U high rack shelf provides mounting holes for fastening two half- rack or four quarter-rack sized units. Pocket-sized devices can also be fastened on the shelf. To order mounting accessories please contact sales@lightware.com.
Locking DC Plug
Twist 90° clockwise to lock.
Rear View – MMX4x2-HT200
Rear View – MMX4x2-HDMI
- 12V DC input connector: 12V DC input for local powering.
- TPS input port: TPS input port for compatible transmitter device (extender / matrix / board).
- HDMI input ports: HDMI input ports for sources. Applied cable shall not be more than 20 m (22AWG) when signal resolution is 4K.
- HDMI output ports: HDMI output ports for sink devices.
- Audio output port: 5-pole Phoenix connector for balanced analog audio.
Rear Panel LEDs
TPS link LED – for MMX4x2-HT200 only
- OFF: No TPS link.
- BLINKING: Device is in low power or Ethernet fallback mode.
- ON: TPS link is live.
HDMI Inputs – SIGNAL LED
- OFF: signal is not present on input.
- ON: signal is present on input.
HDMI Outputs – SIGNAL LED
- OFF: output signal is not present or muted.
- ON: signal is present.
HDMI Outputs – HDCP LED
- OFF: output signal is not HDCP-encrypted.
- BLINKING: non-HDCP capable device is connected, encrypted signal is replaced with red screen.
- ON: output signal is HDCP-encrypted.
Compact Size Matrix Concept
MMX4x2 series device is a multifunctional audio/video matrix switcher with four inputs and two outputs. The HT200 model is built with HDBaseTTM (TPS) technology. The device can be controlled over various interfaces, e.g. Ethernet, USB, RS-232, and Infrared. The matrix is built with audio embedder and de-embedder functions.
Z Only MMX4x2-HT200 model has TPS input. MMX4x2-HDMI model has HDMI + analog audio input and HDMI + analog audio outputs.
Connecting Steps
- CATx: For MMX4x2-HT200 only: connect the matrix and the TPS transmitter by a CATx cable via the TPS connectors.
- HDMI: Connect the matrix and the source devices (e.g. Blu-ray player) using the HDMI inputs and HDMI cables.
- HDMI: Connect the sink devices to the HDMI output port by HDMI cables.
- Audio: Optionally for analog output connect an audio device (e.g. audio amplifier) to the analog audio output port by an audio cable.
- Audio: Optionally for audio extension: connect the audio source (e.g. media player) to the audio input port by an audio cable.
- IR: Optionally for Infrared extension:
- Connect the IR emitter to the IR OUT port of the matrix, and/or
- Connect the IR detector to the IR IN port of the matrix.
- LAN: Optionally connect the matrix to a LAN in order to control the device.
- RS-232: Optionally for RS-232 extension: connect a controller/controlled device (e.g. touch panel) to the RS-232 port.
- Power: Connect the power adaptor to the DC input on the matrix first, then to the AC power socket.
Front Panel Operation
Video Select Buttons
Use the buttons for selecting the video input source. The sequence is the
following for each device.
MMX4x2-HDMI:
Set Audio Config Button
Use the button to select the audio configuration mode. The sequence is:
-
1: Copy HDMI OUT 1 audio to HDMI OUT 2 and AUDIO OUT.
-
2: Copy HDMI OUT 2 audio to HDMI OUT 1 and AUDIO OUT.
-
3: Use audio from Analog Input on all outputs.
-
4: Keep Original Audio on HDMI outputs, de-embed from HDMI OUT 2 to Analog Audio Output.
Software Control – Using Lightware Device Controller (LDC)
The device can be controlled from a computer through the Ethernet, RS-232, and
USB ports using Lightware Device Controller. Please download the application
from www.lightware.com, install on a Windows PC or a macOS and establish
connection to the device. Z The default IP address of the device is:
192.168.0.100, DHCP is disabled.
Set Dynamic IP Address (DHCP)
- Keep the Set Audio Config button pressed for 5 seconds; all front panel LEDs start to blink.
- Release the button, then press it 3 times quickly. DHCP is now enabled.
Restore Factory Default Settings
- Keep the Set Audio Config button pressed for 10 seconds; after 5 seconds front panel LEDs start to blink but keep the button pressed; the LEDs start to blink faster 5 seconds later.
- Release the button, then press it 3 times quickly; factory default settings are restored:
Typical Application
Standalone layout – MMX4x2-HDMI
Typical Application Standalone layout – MMX4x2-HT200
Maximum Extension Distances for MMX4x2-HT200
Resolution
|
Pixel clock rate
| Cable lengths
(Auto / Long reach TPS mode)
---|---|---
CAT5e AWG24| CAT7 AWG26| CAT7 AWG23
1024×768@60Hz| 65 MHz| 100 m / 130 m| 90 m / 120 m| 120 m / 170 m
1280x720p@60Hz| 73.8 MHz| 100 m / 130 m| 90 m / 120 m| 120 m / 170 m
1920x1080p@60Hz (24bpp)| 148.5 MHz| 100 m / 130 m| 90 m / 120 m| 120 m / 170
m*
1920×1200@60Hz| 152.9 MHz| 100 m / NA| 90 m / NA| 120 m / NA
1600×1200@60Hz| 162 MHz| 100 m / NA| 90 m / NA| 120 m / NA
1920×1080@60Hz (36bpp)| 223 MHz| 70 m / NA| 70 m / NA| 100 m / NA
3840×2160@30Hz UHD| 297 MHz| 70 m / NA| 70 m / NA| 100 m / NA
4096×2160@30Hz 4K| 297 MHz| 70 m / NA| 70 m / NA| 100 m / NA
MMX4x2-HT200 Port Diagram
Audio Cable Wiring Guide
MMX4x2 series matrix is built with 5-pole Phoenix input and output connectors.
See below a few example of the most common assembling cases.
Wiring Guide for RS-232 Data Transmission
MMX4x2 series devices are built with 3-pole Phoenix connector. See the below examples of connecting to a DCE (Data Circuit-terminating Equipment) or a DTE (Data Terminal Equipment) type device:
For more information about the cable wiring, see the user’s manual of the device or the Cable Wiring Guide on our website.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>