LIGHTWARE Power Tray Series Rack-Mountable User Guide
- June 1, 2024
- LIGHTWARE
Table of Contents
Power Tray Series Rack-Mountable
“`html
Product Information
Specifications:
-
Models: OPTJ Power tray SC, OPTJ Power tray
NTD, OPTJ Power tray NTQ -
Optical Connector: SC duplex (8x) for SC
model, Neutrik NO4FDW-A (4x) for NTQ model, Neutrik NO2-4FDW-A (4x)
for NTD model -
Number of Installable OPTJ Extenders: Up to 16
for all models -
Power Source: Accepts 100 to 240 Volts, 50 or
60 Hz power sources
Product Usage Instructions:
Assembly Steps of HDMI20-OPTJ-TX/RX90 Extenders:
-
Step 1 – Removing of the Small Cover:
Remove optical cables from cable clamps on the small cover. Unscrew
8 screws using a PH1 screwdriver from locations highlighted with
green arrows. Remove the small cover plate. -
Step 2 – Installation of the OPTJ
Extenders:
Insert each extender into the mounting slot. Pull HDMI tail cable
across the rear side mounting holes. Fasten extenders using
provided M3x6 screws and toothed foot washers. -
Step 3 – USB Cable Connection:
Connect USB-A cables of extenders to USB-A connectors of the Power
tray. Fasten USB cables with provided cable ties. The USB
connectors are for powering purposes only, no data
transmission. -
Step 4 – Re-inserting of the Small
Plate:
Insert the small cover plate back and fasten the 8 screws using a
PH1 screwdriver.
FAQ:
Q: What do the status LED indicators represent?
A: The status LED indicators provide immediate feedback about
the recent status of the HDMI20-OPTJ-TX/RX90 extenders.
Q: What power source does the product accept?
A: The product accepts power sources ranging from 100 to 240
Volts at 50 or 60 Hz.
Q: How many optical connectors are there in each model?
A: The SC model has 8 SC duplex fiber optical connectors, the
NTD model has 4 Neutrik NO2-4FDW-A connectors, and the NTQ model
has 4 Neutrik NO4FDW-A connectors.
“`
Quick Start Guide
OPTJ Power tray SC OPTJ Power tray NTD OPTJ Power tray NTQ
Front View
Rear View
1
2
3
4
5
The OPTJ Power tray NTQ model can be seen in the rear view picture but the layout of all three models is the same.
1 Status LED
indicators of the OPTJ extenders
2 Power LED 3 AC connector
4 Fiber optical
connectors (variable by models)
5 Mounting slots
for the OPTJ extenders
The status LED indicators give immediate feedback about the recent status of
the HDMI20-OPTJ-TX/RX90 extenders.
Power LED lights green when the unit is powered on.
Standard IEC power connector. Accepts 100 to 240 Volts, 50 or 60 Hz power
sources. SC model: 8x SC duplex fiber optical connectors for 16x multimode SC
fiber optical cables. NTD model: 4x Neutrik NO2-4FDW-A connectors for 4x
Neutrik opticalCON DUO series cables or 8x LC fiber optical cables. NTQ model:
4x Neutrik NO4FDW-A connectors for 4x Neutrik opticalCON QUAD series cables.
16x mounting slots for the HDMI20-OPTJ-TX/RX90 extenders.
Important Safety Instructions
Please read the supplied safety instruction document before using the product
and keep it available for future reference.
CLASS 1 LASER PRODUCT IF OPTICAL EXTENDERS
ARE INSTALLED
The device is Class 1 laser product if the HDMI20-OPTJ-90 series extenders are
installed.
Introduction
Thank you for choosing OPTJ Power tray series. The Power tray is a 1RU-size
housing accessory which can enclose up to 16 HDMI20-OPTJ-TX/RX90 units, also
providing power source for every installed device. The optical fibers are
connected to the eight SC duplex or four Neutrik opticalCON QUAD or four
Neutrik opticalCON DUO connectors, each carrying four signal fibers from four
of the extenders. The HDMI tail cables of the extenders are accessible
directly at the back of the Power tray.
Model Comparison
Model
OPTJ Power tray SC OPTJ Power tray NTQ OPTJ Power tray NTD
Optical connector
SC duplex (8x) Neutrik NO4FDW-A (4x) Neutrik NO2-4FDW-A (4x)
Number of installable OPTJ extenders up to 16
up to 16
up to 8
Assembly Steps of HDMI20-OPTJ-TX/RX90 Extenders The following assembly guide is for help the correct installation of the HDMI20-OPTJ-TX/RX90 extenders to the Power tray step by step. Step 1 – Removing of the small cover. Remove the optical cables from the cable clamps located on the small cover. Remove the 8 pcs screws by a PH1 screwdriver from the locations highlighted with green arrows and remove the small cover plate (grey colored).
Step 2 – Installation of the OPTJ extenders. Insert each HDMI20-OPTJ-TX/RX90 extender to the mounting slot. Pull the HDMI tail cable across the rear side mounting holes of the Power tray. Fasten the extenders by the provided M3x6 screws and the toothed foot washers (2 pcs screws and 2 pcs washers per extenders on the top).
Step 3 – USB cable connection. Connect the USB-A cables of the extenders to the USB-A connectors of the Power tray (grey colored). Fasten the USB cables with the provided cable ties. The USB-A connectors of the Power tray are for powering purpose only. No data transmission is processed on them.
Box Contents
Step 4 – Re-inserting of the small plate.
Insert the small cover plate (grey colored) back and fasten the 8 pcs screws
by a PH1 screwdriver.
Step 5 – SC fiber cable connections. Remove the protective caps and connect the SC fiber optical cables to the extenders and insert the optical cables to the cable clamps.
TAKE CARE OF ME
OPTJ Power tray series device
IEC power cable
M3x6mm screw and toothed foot washer (16x)
Cable tie (16x)
SWaafertryanatnyd Info
Quick Start Guide
Safety and Warranty Info, Quick Start Guide
I AM THE ONE AND ONLY USER DOCUMENT FOR
THIS PRODUCT
Lightware Visual Engineering PLC. Budapest, Hungary
sales@lightware.com +36 1 255 3800 support@lightware.com +36 1 255 3810
©2023 Lightware Visual Engineering. All rights reserved. All trademarks
mentioned are the property of their respective owners. Specifications are
subject to change without notice. Further information on the device is
available at www.lightware.com. Doc. ver.: 1.3 19210105
Mounting with Rack Ears The rack ears allow mounting the device as a standard rack unit installation.
Typical Application HDMI 2.0 optical matrix assembly: by connecting the HDMI connectors outputs of the fully populated Power tray with the input and output ports of an MX2-8×8-HDMI20-Audio-L matrix a HDMI 2.0 optical matrix system can be created with Full 4K UHD at 60 Hz 4:4:4 maximum resolution.
Mechanical Drawings The OPTJ Power tray NTQ model can be seen in the figures
but the layout of all three models is the same. The dimensions are in mm.
Front View (1:6)
44.2
44.2
44.2
Always use all the four screws for fixing the device ears to the rack rail. Choose properly sized screws for mounting. Keep minimum two threads left after the nut screw. The device is rack-size width and 1U high.
rack screw flat washer
device mounting ear
rack rail cage nut
Ventilation To ensure the correct ventilation and avoid overheating let enough free space around the appliance. Do not cover the appliance, let the ventilation holes free on the front and the right side.
min. 2 thread left
444.5 482.6 Rear View (1:6)
444.5 482.6 Side View (1:6)
300
Important Safety Instructions
WARNING
Class I Apparatus Construction
Top View (1:6)
Please read and keep the information in the attached safety instructions supplied with the To prevent injury, the apparatus is recommended to securely attach to the floor/wall or This equipment must be used with a mains power system with a protective earth connection.
product before starting using the device.
mount in accordance with the installation instructions. The apparatus shall not be exposed The third (earth) pin is a safety feature, do not bypass or disable it. The equipment should be
to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed operated only from the power source indicated on the product.
on the apparatus. No naked flame sources, such as lighted candles, should be placed on the To disconnect the equipment safely from power, remove the power cord from the rear of the
apparatus.
equipment, or from the power source. The mains plug is used as the disconnect device, the
WEEE ( Waste Electrical & Electronic Equipment ) Correct Disposal of This Product
disconnect device shall remain readily operable. There are no user-serviceable parts inside of the unit. Removal of the cover will expose dangerous voltages. To avoid personal injury, do not remove the cover. Do not operate the unit without the cover installed.
Safety Symbols Legend Symbol Description
This marking shown on the product or its literature, indicates that it should
not be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human
health from, uncontrolled waste disposal, please separate this from
The appliance must be safely connected to multimedia systems. Follow
instructions described in this manual.
Ventilation
Alternating current
other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
For the correct ventilation and avoid overheating ensure enough free space around the appliance. Do not cover the appliance, let the ventilation holes free and never block or bypass
Protective conductor terminal
Household users should contact either the retailer where they purchased, this product, the ventilators (if any).
444.5
Caution, possibility of electric shock
or their local government office, for details of where and how they can take this item for environmentally safe recycling.
482.6
Caution Laser radiation
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
300
Specifications General
Compliance……………………………………………………………………………………….CE, UKCA EMC
(Emission)……………………………………………………………EN 55032:2015+A1:2020 EMC
(Immunity)………………………………………………………….EN 55035:2017+A11:2020
Safety……………………………………………………………………………………. EN 62368-1:2020
RoHS ………………………………………………………………………………………..EN 63000:2018
Laser safety …………………………………………………………….EN 60825-1:2014+A11:2021 Laser class
specification…………..Class 1 if HDMI20-OPTJ-90 extenders are installed Warranty
………………………………………………………………………………………………. 3 years Operating temperature
……………………………………………… 0 to +50°C (+32 to +122°F) Operating humidity
………………………………………………… 10% to 90%, non-condensing
Cooling………………………………………………………………………………………………… Passive Protection
against…………………………………………………………….Short circuit / Overload
Enclosure Rack mountable………………………………………………………………………………………….. Yes Material
…………………………………………………………………………………………… 1 mm steel Dimensions (mm /
inch)…………………….. 482.6W x 300D x 44.2H / 19W x 11.8D x 1.7 Net Weight
……………………………………………………………………………….. 4.13 kg / 9.1 lbs
Power
Power supply …………………………………………………………………………………………Internal Power
source………………………………………………………………….100-240 V AC 50/60 Hz Power consumption
(loaded with 16 extenders)………………………………………… 23.7 W
Optical connectors – OPTJ Power tray SC Connector type
…………………………………………………………………. SC duplex receptacle Number of connectors
……………………………………………………………………………………..8
Optical connectors – OPTJ Power tray NTD Connector type
………………………………………………….Neutrik NO2-4FWD-A receptacle Number of connectors
……………………………………………………………………………………..4
Optical connectors – OPTJ Power tray NTQ Connector type …………………………………………………….
Neutrik NO4FWD-A receptacle Number of connectors
……………………………………………………………………………………..4
USB connectors Connector type ………………………………………………………………..USB Type A receptacle
Number of connectors ……………………………………………………………………………………16 DC output
voltage………………………………………………………………………………………….5V
Installation of the OPTJ Extenders for the OPTJ Power tray NTD The OPTJ Power tray NTD model is built with 4x Neutrik opticalCON DUO connectors which can extend up to 8x optical signals. The OPTJ Power tray NTD model is able to handle up to 8 pcs HDMI20-OPTJ-TX/RX90 extenders. The mounting slots (highlighted with green) and the Neutrik opticalCON DUO connectors (highlighted with blue) are labeled with the same ID for the better identification. Thus, the installation of the extenders are recommended to the following slots in the NTD model:
Extender installation
Mounting slots 1A (1) 1B (2) 1a (3) 1b (4) 2A (5) 2B (6) 2a (7) 2b (8) 3A (9) 3B (10) 3a (11) 3b (12) 4A (13) 4B (14) 4a (15) 4b (16)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>