STEINBACH 040590 Hanging cartridge filter unit for above ground pools Instruction Manual

June 5, 2024
Steinbach

STEINBACH-logo

STEINBACH 040590 Hanging cartridge filter unit for above-ground pools

STEINBACH-040590-Hanging-cartridge-filter-unit-for-above-ground-pools-
Product

Safety Warnings

Your cartridge filter has been thoroughly tested after production and left the factory in technically perfect condition. In order to maintain this condition and to ensure safe functioning, the user should observe all the recommendations given in these instructions at all times. If there are any signs that safe operation of the cartridge filter may no longer be guaranteed, the system is to be disconnected from the electricity supply immediately and secured against unintentional switching on again. This is the case:

  • if the device shows visible damage.
  • if the device appears to be no longer functioning correctly.

Set-Up Diagram (Picture 1)

Note: The cartridge filter can be adjusted in height. The extension rod and clamp are fixed in place with a flat-head, star-drive screw and a hexagon nut to avoid the device floating to the surface in the pool.

STEINBACH-040590-Hanging-cartridge-filter-unit-for-above-ground-pools-
fig-1

Technical Data

  • Model Suspended/Wall-mounted cartridge filter for set-up pools
  • Nominal voltage 12 VAC (50HZ)
  • Filter volume 2,8 l
  • Flow rate 1.700 l/h
  • Pool volume 8.000 l
  • Output (W) 20
  • Max. Water temp. °C 35
  • Max. depth below water (m) 0,5
  • Transformer SG12 20,4 W, 230 V 50 Hz, 12 VAC 1700MA 20,4 VA
  • Do not use the pump if there is no water in the pool.
  • Before the filter pump is started up, please check that all cables and the plug are in perfect condition.
  • Voltage and frequency must comply with those stated.
  • The transformer must be kept at a distance of at least 3.5 meters from the pool.
  • The transformer, cable and plug must be kept dry.
  • Before servicing the pump and cleaning the particle filter, make sure that the transformer has been disconnected from the electricity supply.
  • If the power cable is damaged, the pump must not be used.
  • This device is not for intended for use by persons (including children) with limited physical, sensory or mental abilities or those with a lack of experience and/or lack of knowledge unless they have been given the task by a person responsible for their safety or have received instructions on how to use the device.
  • Children should be supervised to ensure that they do not play with the device.
  • If the connecting cable on this device is damaged, it must be replaced by the manufacturer or his After-Sales Service or a similarly qualified person in order to avoid hazards.
  • Do not lift or move the pump by pulling on the power cable.

Using for the first time

Caution: never let the pump run dry; this leads to damage.

  • Submerge the filter pump completely in the water and ensure that the pump is filled with water.
  • In order to avoid the pump sucking air, submerge the pump at least 15 cm below water level.
  • The water temperature must not be above 35°C.
  • During winter avoid the pump becoming frozen.
  • The pump switches on immediately after plugging the transformer into the socket

Winter

  • Unplug the pump from the power source.
  • Store the filter system in a location protected from frost and severely cold temperatures. In a garage or insulated storage shed is recommended.

Troubleshooting

Problem Cause Possible remedy

The motor does not run

| ****

No electricity

| Check electricity source, switch and wiring (have them repaired or replaced by professionals)
Impeller is blocked| Dismantle     pump and clean
Windings burnt out| Replace pump




Motor runs but little or no water is drawn in

| The pump is not fully submerged in water| Raise the water level or lower the pump
Impeller damaged| Clean filter insert
The rotor turns in the wrong direction| Switch transformer off and then back on again
Motor runs in- intermittently| The impeller is blocked or is permanently overloaded| Clean cartridge and protect trans- former against overheating.

Steinbach VertriebsgmbH, Aistingerstrasse 2, 4311 Schwertberg, Österreich FR/IT/CZ/HU/HR/SK/SLO/RO/BG/TR: +43 (0) 7262 / 61431-0
e-mail: service@steinbach.at
www.steinbach.at

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals