Steinbach Technikbox Pool Equipment Box Owner’s Manual

Steinbach Technikbox Pool Equipment Box

Product Information

The Technikbox is a storage box designed to store pool equipment. It comes with three side parts and bottom part, two front and back parts, one cover, and an operating manual. The box has dimensions of 910 mm x 680 mm x 830 mm and is model number 036600.

Product Usage Instructions

Preparing the Setup Location and Connections
To set up the Technikbox, you will need the following tools and materials:

• Drill with 45 mm or 75 mm hole saw

Follow these steps to prepare the setup location and connections:

1. Ensure that there is at least one meter of distance between the pool and the Technikbox.
2. Ensure that the ground where you will be placing the Technikbox is stable, level, water-resistant, and slip-resistant.
3. Connect the water inlet and outlet to the Technikbox.

Assembly

Follow these steps to assemble the Technikbox:

1. Attach the front and back parts (2x) together.
2. Attach the side parts (3x) to the front and back parts.
3. Attach the bottom part (3x) to the front part.
4. Insert the cover (1x) on top of the Technikbox.

Cleaning
The Technikbox can be cleaned using a damp cloth. Do not use abrasive cleaners or solvents as they may damage the product.

Disposal
Dispose of the packaging materials by separating them according to their material type and recycling them accordingly. Dispose of the product according to the guidelines and regulations set by your country.

Equipment box

General Information

Read and keep the operating instructions
These operating instructions are a part of this equipment box (hereinafter called “product”). They contain important information about start-up and operation.
Read the operating instructions and especially the safety instructions carefully before using the product. Non-observance of this operating instructions manual may lead to severe injuries or damage to the product.
Keep the operating instructions for further use. If you pass on the product to a third party, you must pass on operating instructions as well.

Intended use
The equipment box exclusively intended for storing the pool equipment.
This product is exclusively intended for private use and not suited for the commercial sector.
Only use the product as described in these operating instructions. Any other use is considered inappropriate and may lead to material damage or even injury. The product is not a toy.
The manufacturer or retailer will not assume any liability for damage caused by inappropriate or incorrect use.

Foreseeable misuse
Never use the product as a step, diving board or starting block.

Explanation of Symbols

The following symbols are used in this operating instructions, on the product or on the packaging.

• Here you will find helpful additional information.
• Risk of damage! Do not open the packaging with sharp or pointed objects, such as cutters

Safety

The following signal words are used in these operating instructions.

• WARNING
• This signal symbol/word denotes a hazard with an average risk level that could lead to death or severe injury if it is not avoided.
• CAUTION!
• This signal symbol/word denotes a hazard with a low risk level that could lead to mild or moderate injury if it is not avoided.
• NOTICE!
  This signal word provides a warning about potential material damage.

General safety instructions

Safety instructions for persons
WARNING!
Packaging materials pose a risk of suffocation!
Catching your head in the packaging foil or swallowing other packaging materials can cause death. There is a higher risk for children and mentally challenged persons who cannot estimate the hazard potential due to lack of knowledge and experience.

• Prevent children and mentally challenged persons from playing with the packaging materials.

CAUTION!
Risk of injury!
In the case of excess strain, the product can cave in.

• The product is not meant to be used as a storage surface! Do not place any objects on the product.
• Never climb or sit on the product.
• Never let persons with reduced physical, sensory or mental capacities (such as children or people under the influence of alcohol) or a lack of experience and knowledge unsupervised near the product.
• Never lift the loaded equipment box.

NOTICE!
Improper use of the product may cause it to become damaged.

• Never use the recessed handles on the side parts to carry the product. The recessed handles are only designed for opening the cover.

Description

The equipment box is ideal to keep your pool equipment clean. In the equipment box, your pool equipment is protected from exposure to weather and dirt. The lines to the pool equipment can be routed through the prepared outlets on the two side parts 3 .

Preparation

Preparing the setup location and the connections
The safest place to set up the equipment box is on a smooth, level concrete or wooden floor.
The right selection and preparation of the setup location makes it much easier to install the product. The following requirements must be met or considered:

• Water supply and discharge line
• At least one meter distance between the pool and the equipment box
• Stable, level, anti-slip surface that is resistant to water

Assembly

CAUTION!
Risk of injury!
Cutting tools can cause injuries.

•  Always keep hands and feet away from the cutting tools, especially when turning on the motor.

Assembling the product
To assemble the equipment box,  proceed as follows:

1. Use a hole saw to drill the outlets for the lines into the side parts 3 . The predefined cutting guides are designed for a 45 mm or 75 mm hole saw.
2. Insert the bottom part 3 into the front part 2 . Pay attention to the positioning of the recesses in the individual parts. The inside of the bottom part points down.
3. Insert the two side parts into the front part. The recesses in the side parts are on the bottom.
4. Insert the back part into the bottom part and into the two side parts. This will require some force. You will hear a dull sound when the back part snaps into place.
5. Put on the cover 1 .
6. Position the equipment box at the prepared setup location.
   The equipment box is assembled.

Loading the equipment box
Observe the following when loading the equipment box:

• Read the operating instructions for the pool equipment before loading the equipment box.
• Guide the lines to the pool equipment through the recesses in both side parts.

The equipment box is loaded.

Cleaning

Only clean the product with a standard bathroom cleaner, clear tap water and a lint-free cloth. Aggressive cleaning agents can damage the product. Dry the product with a lint-free cloth.

Storage
Observe the operating instructions for the pool equipment.
After thorough cleaning and drying, store the product in a dry and frost-free place (= +5 °C).

Technical data

• Model 036600
• Outer dimensions/setup dimensions (L x W x H) 910 mm x 680 mm x 830 mm
• max. inner dimensions (L x W x H) 740 mm x 550 mm x 700 mm

Spare parts

1. 036601 – Front and back part
2. 036602 – Side and bottom part
3. 036603 – Cover

Disposal

Disposing of the packaging
Sort the packaging before you dispose of it. Dispose of paperboard and cardboard with the recycled paper service and wrappings with the appropriate collection service.

Disposal of the product
Dispose of the product in line with the guidelines and regulations valid in your country.

References

• Steinbach Helpdesk
• Steinbach Pools und Poolzubehör - “we are pool”
• Pool Ersatzteile und Zubehör bequem online bestellen | Steinbach
• Steinbach Helpdesk
• Steinbach Pools und Poolzubehör - “we are pool”
• Pool Ersatzteile und Zubehör bequem online bestellen | Steinbach

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>