makita SD100D Cordless Drywall Saw Instruction Manual
- June 5, 2024
- Makita
Table of Contents
Cordless Drywall Saw
INSTRUCTION MANUAL
|
---|---
|
(Original instructions)
SPECIFICATIONS
Model: | SD1OOD |
---|---|
Length of stroke | 6 mm |
Strokes per minute | 0 – 6,000 min.’ |
Maximum cutting capacities | Drywall |
Wood | 15 mm |
Rated voltage | D.C. 10.8 V |
Standard battery cartridges | BL1015, BL1020B |
Overall length | 239 mm |
Net weight | 1.5 kg |
- Due to our continuing program of research and development, the specifications herein are subject to change without notice.
- Specifications and battery cartridges may differ from country to country.
- Weight, with battery cartridge, according to EPTA-Procedure 01/2003
Intended use
This tool is intended for the plunge-cutting of drywall.
Wood can also be cut by installing a suitable saw blade.
Noise
The typical A-weighted noise level is determined according to 60745-2-11:
Sound pressure level
(LpA) : 77 dB(A)
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
WARNING: Wear ear protection.
Vibration
The vibration total value (tri-axial vector sum) was determined according to
60745-2-11:
Work mode: cutting drywall (thickness 30 mm)
Vibration emission (ah) : 3.0 m/s 2 Uncertainty (K) : 1.5 m/s 2
Work mode: cutting chipboard (thickness 15 mm)
Vibration emission (ah) : 5.5 m/s 2
Uncertainty (K) : 1.5 m/s 2
NOTE: The declared vibration emission value has been measured in
accordance with the standard test method and may be used for comparing one
tool with another.
NOTE: The declared vibration emission value may also be used in a
preliminary assessment of exposure.
WARNING: The vibration emission during actual use of the power tool can
differ from the declared emission value depending on the ways in which the
tool is used. **WARNING: Be sure to identify safety measures to protect
the operator that are based on an estimation of exposure in the actual
conditions of use (taking account of all parts of the operating cycle such as
the times when the tool is switched off and when it is running idle in
addition to the trigger time).
EC Declaration of Conformity
For European countries only**
The EC declaration of conformity is included as Annex A to this instruction
manual.
SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fire and/or serious
injury. Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
Cordless drywall saw safety warnings
- Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
- Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control.
- Always use safety glasses or goggles. Ordinary eye or sunglasses are NOT safety glasses.
- Avoid cutting nails. Inspect the workpiece for any nails and remove them before operation.
- Do not cut the oversize workpieces.
- Check for the proper clearance beyond the workpiece before cutting so that the blade will not strike the floor, workbench, etc.
- Hold the tool firmly.
- Make sure the blade is not contacting the workpiece before the switch is turned on.
- Keep hands away from moving parts.
- Do not leave the tool running. Operate the tool only when hand-held.
- Always switch off and wait for the blade to come to a complete stop before removing the blade from the workpiece.
- Do not touch the blade or the workpiece immediately after operation; they may be extremely hot and could burn your skin.
- Do not operate the tool at no-load unnecessarily.
- Some material contains chemicals that may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data.
- Always use the correct dust mask/respirator for the material and application you are working with.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity with the product (gained from
repeated use) replace strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety rules stated in this
instruction manual may cause serious personal injury.
Important safety instructions for battery cartridge
-
Before using the battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using the battery.
-
Do not disassemble the battery cartridge.
-
If the operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns, and even an explosion.
-
If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.
-
Do not short the battery cartridge:
(1) Do not touch the terminals with any conductive material.
(2) Avoid storing battery cartridges in a container with other metal objects such as nails, coins, etc.
(3) Do not expose the battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. -
Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50 °C (122 °F).
-
Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire
-
Be careful not to drop or strike the battery.
-
Do not use a damaged battery.
-
The contained lithium-ion batteries are subject to the Dangerous Goods Legislation requirements.
For commercial transports e.g. by third parties or forwarding agents, special requirements on packaging and labeling must be observed. For the preparation of the item being shipped, consulting an expert for hazardous material is required. Please also observe possibly more detailed national regulations. Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging. -
Follow your local regulations relating to the disposal of batteries.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that have been altered, may
result in the battery bursting causing fires, personal injury and damage. It
will also void the Makita warranty for the Makita tool and charger.
Tips for maintaining maximum battery life
- Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power.
- Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.
- Charge the battery cartridge with room temperature at 10 °C – 40 °C (50 °F – 104 °F). Let a hot battery cartridge cool down before charging it.
FUNCTIONAL DESCRIPTION
CAUTION: Always be sure that the tool is switched off and the battery
cartridge is removed before adjusting or checking the function on the tool.
Installing or removing battery cartridge
CAUTION: Always switch off the tool before installing or removing of the
battery cartridge.
CAUTION: Hold the tool and the battery cartridge firmly when installing
or removing the battery cartridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your hands and result in damage to
the tool and attery cartridge and a personal injury.
► Fig.1: 1. Red indicator 2. Button 3. Battery cartridge To remove the battery
cartridge, slide it from the tool while sliding the button on the front of the
cartridge. To install the battery cartridge, align the tongue on the battery
cartridge with the groove in the housing and slip it into place. Insert it all
the way until it locks in place with a little click. If you can see the red
indicator on the upper side of the button, it is not locked completely.
CAUTION: Always install the battery cartridge fully until the red
indicator cannot be seen. If not, it may accidentally fall out of the tool,
causing injury to you or someone around you.
CAUTION: Do not install the battery cartridge forcibly. If the cartridge
does not slide in easily, it is not being inserted correctly.
Battery protection system
The tool is equipped with a battery protection system.
This system automatically cuts off power to the motor to extend battery life.
The tool will automatically stop during operation if the tool and/or battery
are placed under one of the following conditions:
Overloaded:
The tool is operated in a manner that causes it to draw an abnormally high
current.
In this situation, turn the tool off and stop the application that caused the
tool to become overloaded. Then turn the tool on to restart.
If the tool does not start, the battery is overheated. In this situation, let
the battery cool before turning the tool on again.
Low battery voltage:
The remaining battery capacity is too low and the tool will not operate. If
you turn the tool on, the motor runs again but stops soon. In this situation,
remove and recharge the battery.
Indicating the remaining battery capacity
Only for battery cartridges with the indicator
► Fig.2: 1. Indicator lamps 2. Check button
Press the check button on the battery cartridge to indicate the remaining
battery capacity. The indicator lamps light up for a few seconds.
Indicator lamps
| Remaining capacity
---|---
|
| 75% to 100%
| 50% to 75%
| 25% to 50%
| 0% to 25%
NOTE: Depending on the conditions of use and the ambient temperature, the indication may differ slightly from the actual capacity.
Switch action
► Fig.3: 1. Switch trigger
CAUTION: Before installing the battery cartridge into the tool, always
check to see that the switch trigger actuates properly and returns to the
“OFF” position when released.
To start the tool, simply pull the switch trigger. Tool speed is increased by
increasing pressure on the switch trigger. Release the switch trigger to stop.
To prevent the switch trigger from being pulled accidentally, the trigger-lock
button is provided. To start the tool, depress the trigger-lock button from
the side and pull the switch trigger. After use, always press in the trigger-
lock button from the side.
► Fig.4: 1. Trigger-lock button
CAUTION: When not operating the tool, depress the trigger-lock button
from the side to lock the switch trigger in the OFF position. Adjusting the
depth of cut
The cutting depth corresponds with the scale on the blade. Loosen the screw on
the blade holder until the blade can move freely. Align the scale on the blade
with the bottom line of the blade holder. Then tighten the screws.
► Fig.5:
- Cutting depth
- The bottom line of the blade holder
- Scale on the blade
The maximum cutting depth depends on the type of the saw blade. Always use the saw blade designed for cutting the working material.
Type of saw blade | Max. cutting depth |
---|---|
For drywall | 30 mm |
For wood | 15 mm |
LED light
CAUTION: Do not look in the light or see the source of light directly.
Pull the switch trigger to light up the lamp. The lamp keeps on lighting while
the switch trigger is being pulled. The lamp goes out approximately 10 seconds
after releasing the trigger.
► Fig.6: 1. Lamp
NOTE: Use a dry cloth to wipe the dirt off the lens of the lamp. Be
careful not to scratch the lens of the lamp, or it may lower the illumination.
ASSEMBLY
CAUTION: Always be sure that the tool is switched off and the battery
cartridge is removed before carrying out any work on the tool. Removing the
dust collector
CAUTION: Never operate the tool without the dust collector. Dust may come
into your eyes and cause eye injury.
To remove the dust collector, hold the tool handle and pull back the tabs on
the tool. Be sure to pull the tabs on both sides at the same time.
► Fig.7: 1. Tab
When installing, align the dust collector’s edge with the groove on the base.
► Fig.8: 1. Groove
Replacing drywall saw blade
CAUTION: Always clean out all chips or for- eign matter adhering to the
blade and/or blade holder. Failure to do so may cause insufficient tightening
of the blade, resulting in a serious personal injury.
CAUTION: Do not touch the blade or the workpiece immediately after
operation. They may be extremely hot and could burn your skin.
CAUTION: Make sure that the blade is prop- erly secured. Insufficient
tightening of the blade may cause blade breakage or serious personal injury.
-
Remove the dust collector.
-
Remove the bolts on the blade holder with the hex wrench.
► Fig.9: 1. Bolts 2. Blade holder 3. Blade -
Set a new blade as shown in the figure. Make sure that the curved edge of the blade points forward. Fit the protrusion of the blade holder into the slot on the blade.
► Fig.10: 1. Slot 2. Protruded portion (opposite side) -
Adjust the cutting depth then tighten the bolts.
-
Attach the dust collector.
Installing snap-off blade
CAUTION: Always use the snap-off blade with designated length, width, and
thickness. An inappropriately installed snap-off blade can be broken. A broken
blade can fly off and cause a personal injury. A snap-off blade can also be
used with this tool. Use 3 segments of 18 mm wide snap-off blade with 0.5 mm
thickness. The maximum cutting depth is 12.5 mm when cutting drywall.
► Fig.11: 1. Three segments of the snap-off blade
- Loosen the bolts on the blade holder. Turn the blade holder so that its protrusion faces outward.
- Insert the snap-off blade so that the sharp edge faces forward.
- Secure the snap-off blade at the position where the end of the first segment comes to the edge of the blade holder as illustrated.
► Fig.12: 1. Blade holder 2. End of the first segment of snap-off blade 3. Allowable cutting length
Attaching blade cap
CAUTION: Always attach the blade cap when the tool is not used. A bare
blade may cause personal injury or damage to the blade itself.
Pass the blade cap through the blade until the hook catches the base cover.
Note the direction of the blade cap when attaching; the wider hook comes front
side. When removing the blade cap, lift it while pinching both sides.
► Fig.13: 1. Blade cap 2. Hook
During operation, insert the blade cap to the hook on the base as illustrated
until it clicks.
► Fig.14: 1. Blade cap 2. Hook
Hex wrench storage
When not in use, store the hex wrench as shown in the figure to keep it from
being lost.
► Fig.15: 1. Hex wrench Connecting a vacuum cleaner
CAUTION: Attach the blade cap before connecting the vacuum cleaner.
Connect a Makita vacuum cleaner for clean operation. Remove the rubber cap on
the dust collector and connect the vacuum cleaner’s hose to the nozzle of the
dust collector.
► Fig.16: 1. Dust collector 2. Rubber cap 3. Vacuum cleaner hose
OPERATION
CAUTION: Hold the tool firmly.
CAUTION: Always hold the base flush with the workpiece during cutting.
Never perform a curved cut. Failure to do so may cause blade breakage,
resulting in a serious injury.
The V-notch and convexed portion in the base cover of the tool indicate the
position of the blade. Always check the blade position when cutting.
The base cover of the tool
► Fig.17: 1. V-notch 2. Convexed portion 3. Blade
NOTE: For accurate cutting, it is recommended to draw cutting lines on
the workpiece beforehand.
-
Place the tip of the blade on the start line. Tilt the tool so that the front edge of the base touches the workpiece. Align the bottom of the V-notch in the front edge with
the cutting line.
► Fig.18 -
Slowly pull the trigger without the blade making any contact with the workpiece. When the blade attains full speed, push the tool toward the workpiece. As the blade pierces the workpiece, make the whole surface ofthe base cover contact with the workpiece.
► Fig.19 -
Move the tool straight forward until the cutting finishes.
MAINTENANCE
CAUTION: Always be sure that the tool is switched off and the battery
cartridge is removed before attempting to perform inspection or maintenance.
NOTICE: Never use gasoline, benzene, thinner, alcohol or the like.
Discoloration, deformation or cracks may result.
Cleaning the base cover
Clean off the cutting chips and dust accumulated on the base cover. Lift the
base cover while pulling the hook on the back end to remove it. Follow the
removal procedure in reverse when installing.
► Fig.20: 1. Base cover 2. Hook
CAUTION: Pay attention to the tip of the blade and cutting chips when
removing the base cover.
NOTICE: Perform the cleaning periodically. Dirty base cover may damage or
deface the working surface.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or
adjustment should be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
OPTIONAL ACCESSORIES
CAUTION: These accessories or attachments are recommended for use with
your Makita tool specified in this manual. The use of any other accessories or
attachments might present a risk of injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding these accessories, sk
your local Makita Service Center.
- Drywall saw blade
- Wood saw blade
- Dust box
- Dust collector
- Hex wrench
- Hook
- Makita genuine battery and charger
NOTE: Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.
Makita Europe N.V.
Makita Corporation
Jan-Baptist Vinkstraat 2,
3070 Kortenberg, Belgium
3-11-8, Sumiyoshi-cho,
Anjo, Aichi 446-8502 Japan
www.makita.com
885530-973
EN, PL, HU, SK,
CS, UK, RO, DE
20160803
Documents / Resources
|
makita SD100D Cordless Drywall
Saw
[pdf] Instruction Manual
SD100D, Cordless Drywall Saw, SD100D Cordless Drywall Saw, Drywall Saw, Saw
---|---
|
makita SD100D Cordless Drywall
Saw
[pdf] Instruction Manual
SD100D, Cordless Drywall Saw, SD100D Cordless Drywall Saw, Drywall Saw, Saw
|
makita SD100D Cordless Drywall
Saw
[pdf] Instruction Manual
SD100D Cordless Drywall Saw, SD100D, Cordless Drywall Saw, Cordless Saw,
Drywall Saw, Saw
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>