IPORT BZL White Surface Mount Bezel iPad Installation Guide
- June 5, 2024
- IPORT
Table of Contents
IPORT BZL White Surface Mount Bezel iPad Installation Guide
BOX CONTENTS
Installation Guide
Surface Mount Bezel (a)
Mounting Bracket (b)
Mounting Screws (d) x 4
Security Tool (e)
PoE Splitter (70718) (f)
SYSTEM COMPONENTS (SOLD SEPARATELY)
PoE Injector (70719) (g) (International Adapters Included)
HARDWARE REQUIREMENTS
The hardware required for each application scenario is shown below. For brick & mortar, concrete, and glass applications, please view our application note for installation on our website, www.iportproducts.com
| DRYWALL | SOFTWOOD | HARDWOOD |
|---|---|---|
| Use provided hardware (use a Phillips hand screwdriver) | Use provided hardware | |
| (use a Phillips hand screwdriver) | Drill pilot holes & use provided hardware |
(use a Phillips hand screwdriver)
BRICK & MORTAR| CONCRETE|
Use brick & mortar anchors & screws (not provided)| Use concrete anchors &
screws (not provided)|
*Apple, iPad, iPad Air, iPad Pro, and Lightning are trademarks of Apple Inc., registered in the U.S. and other countries.
Before Installation
Ensure the selected wall for installation is free of plumbing or any other obstructions.
Electrical Wall Box for the PoE Splitter
The PoE Splitter can be used with US, UK, and Euro single gang electrical
boxes. The recommended depth for the UK electrical box is a minimum of 1.4″
(35mm) and the Euro wall box is a minimum of 1.85″ (47mm). An open double gang
electrical box may be used to allow for flexible wire management.
For Advanced Installation
iPort offers an elegant solution to integrating the iPad onto any surface.
For advanced surface installation applications such as masonry, concrete, and
glass, please view our application note for installation on our website,
www.iportproducts.com.
For drywall and wood installation, please proceed to the installation steps
noted below.
Preparation for Installation
Choose your power/wiring scenario:
Accessories required for each power and wiring scenario
| Bezel | PoE Splitter | PoE Injector |
|---|
PoE Switch Powered|
---|---
24V Powered|
Receptacle Powered|
| | PoE Splitter – 70718
The PoE splitter is designed to provide the necessary power to the iPad’s
Lightning Connector from a PoE or direct 24V power source. For more detailed
information, see the enclosed diagrams.
---|---|---
| | PoE + Injector – 72106
The PoE+ injector is designed to provide power via PoE+ (IEEE 802.3at) and is
required if there is no other PoE+ Switch or power source.
When removing the Surface Mount (a) bezel from its box, the bezel will be attached to the (b) mounting bracket. To decouple the (a) bezel from the (b) mounting bracket, place the (a) bezel face up on a flat and smooth surface. With one hand, hold the (b) mounting bracket in place. With your opposite hand, lift the right edge of the (a) bezel and then the left to decouple the magnets. This will help avoid bending of the metal and prevent any damage to the (a) bezel or (b) mounting bracket.
Locate the ideal mounting area. For a retrofit installation, locate an
existing low-voltage electrical box. For new construction, choose a location
for an electrical box. We recommend installing the (a) bezel in landscape
orientation, but it can also be installed in portrait orientation.
Note: A single gang electrical box allows you to use the Surface Mount
in portrait or landscape orientation, and a double gang electrical box allows
you to use the Surface Mount in a landscape-only orientation. Surface Mount
for iPad Pro 12.9″ can be configured for audio out via lightning connector and
ethernet via lightning connector with additional components. Please use a
double-gang box in these scenarios. For more information, visit
iportproducts.com/surfacemount.Install the (b)
mounting bracket on the wall with the (b) bracket surrounding the electrical box. Use the center lines as a guide to install the (d) mounting screws. Our specialized (d) mounting screws act as anchors and screws when mounting on a drywall or wood surface.
Note: Use all six mounting screws for Surface Mount for iPad Pro 12.9″.Using the recommended screwdriver and (d) mounting screws, install the first screw in the upper left-hand corner.
Level the (b) mounting bracket over the wiring location and fasten (b) bracket with the remaining (d) screws. Lining up the (d) mounting screws with the engraved center lines provided on the (b) bracket will allow you optimal adjustability. The (b) mounting bracket is now in place.
Place the Surface Mount (a) bezel face down on a flat and smooth surface with the iPort logo on the left.
Plug in the iPad’s lightning to USB cable directly into the iPad. Position the
iPad facedown into the (a) bezel with the iPad cable on the left. Carefully
wrap the iPad cable around the metal loop located on the (a) bezel. To lock
the iPad in place, use a flat head screwdriver to deploy the second and third
toggles located on the right side of the Surface Mount (a) bezel. The first
top-right toggle is a power button extension.
Note: iPad Pro 12.9″ Bezel contains three toggles.
Connect the USB connector to the USB port located on the (f) PoE splitter. Tightly wrap the remaining iPad cable around the (f) PoE splitter. Leave enough slack on the iPad cable to place (f) PoE splitter into the electrical box.
Connect the appropriate power source identified in the Power and Wiring Guide
(found in (f) PoE splitter box). Place the PoE splitter into the single gang
box located in the wall with the iPort logo facing out.
NOTE: If you need to remove the (f) PoE splitter from the wall box, you
can use needle-nose pliers to grab onto the holes provided on the front of the
(f) PoE splitter.
With the iPad home button facing left or right, the Surface Mount will attach to the (b) mounting bracket with internal magnets.To lock the Surface Mount in place, use the (e) security tool provided to engage the security locks. When the bezel is in
landscape orientation, the security holes are located on the top-right and bottom-left of the bezel. Rotate the (e) security tool counter-clockwise to engage the locks, and clockwise to unlock the Surface Mount (a) bezel from the (b) mounting bracket.
REMOVAL: Start with step #9 making sure to turn the security tool clockwise to disengage the locking screw. Continue to work from step #9 to step #5 to remove the iPad from the bezel.
Warranty information at
iportproducts.com/warranty
336-0027 REV B
www.iportproducts.com