IPORT 72385 CONNECT Wedge Mount and Cable Owner’s Manual

IPORT 72385 CONNECT Wedge Mount and Cable

Product Information

The IPORT CONNECT Platform is a revolutionary system designed to enhance your user experience. It includes the IPORT CONNECT Wedge Mount and the IPORT CONNECT PRO Case, providing a secure and convenient solution for mounting and using your iPad.

Product Usage Instructions

1. Use the provided IPORT Security tool to unlock the Wedge Mount from the Security foot. Insert the tool into the small holes on the left and right of the WegeMount. Turn the tool counterclockwise until it stops spinning.
2. Place the Security foot in the desired location, drill pilot holes, and use the 4 provided screws to secure the security foot to a solid surface.
3. Flip the Wedge Mount over and insert the CAT6 cable into the RJ45 of the PoE+ Adapter inside the CONNECT Wedge Mount.
4. Option A: Run the CAT6 cable through the center of the security foot for a clean cable-free install.
5. Option B: Run the cable out the back of the WedgeMount, making sure to remove the cable channel cover.
6. Reinstall the WedgeMount onto the security foot, ensuring that the front of the security foot is hooked to the WedgeMount and set firmly down.
7. Use the provided IPORT Security Tool to lock the WedgeMount to the security foot. Turn the tool clockwise until it stops on both sides of the Wedge Mount.
8. Remove the Case Top from the IPORT CONNECT PRO Case by pressing up and separating the two halves of the case.
9. Remove the electronics board from the IPORT CONNECT PRO Case by pressing up the release tab toward the top of the case. Make sure to disconnect the two attached cables.
10. Place the Case onto the WedgeMount, ensuring that the Molex cable is run through the center of the Case before placing it on the WedgeMount.
11. Insert the Mounting Plate into the Case and feed the Molex cable through the center hole. Make sure the Mounting plate clips into place.
12. Use the 4 provided machine screws to secure the Mounting Plate and Case to the WedgeMount.
13. Connect the two Molex cables together and place them in the channel of the mounting bracket.
14. Install the iPad into the Case and attach the Case Top.
15. Use the provided IPORT Security tool to lock the Case top onto the Case, securing the iPad.

Once you have completed these steps, your IPORT CONNECT Platform setup is complete and ready to use.

IPORT CONNECT WEDGE MOUNT Install Manual

Thank you for purchasing the all new IPORT CONNECT Platform. We hope you enjoy this
revolutionary new system and if at any time you need more assistance please contact IPORT Tech Support via Online chat or through our help desk.
– IPORT Team

IPORT CONNECT WEDGEMOUNT Install PoE+ Data

1. Use the Provided IPORT Security tool to unlock the Wedge Mount from the Security foot. Insert the tool into the small holes found on the left and right of the WegeMount. Turn the tool counterclockwise until the tool stops spinning.

2. Place the Security foot in the desired location, drill pilot holes and use the 4 provided screws to secure the security foot to a solid surface.

3. Flip the Wedge Mount over and insert the CAT6 cable into the RJ45 of the PoE+ Adapter inside the CONNECT Wedge Mount.

4. Option A, Run the cat6 cable through the center of the security foot for a clean cable free install.

5. Option B, Run the cable out the back of the WedgeMount making sure to remove the cable channel cover.

6. Reinstall the WedgeMount onto the security foot making sure to hook the front of the security foot to the WedgeMount and set firmly down.

7. Use the provided IPORT Security Tool to lock the WedgeMount to the security foot. Turn the tool clockwise until it stops on both sides of the Wedge Mount.

8. Remove the Case Top from the IPORT CONNECT PRO Case by pressing up and separating the two halves of the case.

9. Remove the electronics board from the IPORT CONNECT PRO Case by pressing up the release tab toward the top of the case. Make sure to disconnect the two attached cables.

10. Place the Case onto the WedgeMount, making sure to run the Molex cable through the center of the Case before placing on the WedgeMount.

11. Insert the Mounting Plate into the Case and feed the Molex cable though the center hole. Make sure the Mounting plate clips into place.

12. Use the 4 provided machine screws and secure the Mounting Plate and Case to the WedgeMount.

13. Connect the two Molex cables together and place in the channel of the mounting bracket.

14. Install the iPad into the Case and attach the Case Top.

15. Use the provided IPORT Security tool to lock the Case top onto the Case securing the iPad.

COMPLETE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>