DYNOJET PC6-23001 Power Commander 6 Installation Guide

: June 3, 2024
: Dynojet

Table of Contents

DYNOJET PC6-23001 Power Commander 6
PARTS LIST
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
WIRE CONNECTIONS
INSTALLING THE POWER COMMANDER 6
Read User Manual Online (PDF format)
Download This Manual (PDF format)

DYNOJET PC6-23001 Power Commander 6

PARTS LIST

1 POWER COMMANDER 6
1 INSTALLATION GUIDE
1 USB CABLE
2 DYNOJET DECALS
2 POWER COMMANDER DECALS
2 VELCRO STRIPS
1 ALCOHOL SWAB
1 POSI-TAP

PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION. THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.

INPUT ACCESSORY GUIDE

OPTIONAL ACCESSORY INPUTS

Map (Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You can switch on the fl y between these two base maps when you hook up a switch to the MAP inputs. You can use any open/close type switch. The polarity of the wires is not important.
Shifter (Input 1 or 2) Used for clutch-less full throttle upshifts. Insert the wires from the Dynojet quick shifter into either Input 1 or Input 2. The polarity of the wires is not important. Set to Input 2 by default.
Speed If your application has a speed sensor then you can tap into the signal side of the sensor and run a wire into this input. This will allow you to calculate gear position in the Control Center Software. Once gear position is setup you can alter your map based on gear position and setup gear dependent kill times when using a quick shifter.
Analog This input is for a 0-5v signal such as engine temp, boost, etc. Once this input is established you can alter your fuel curve based on this input in the Power Core software.
Launch You can connect a wire to either Input 1 or Input 2 and then the other end to a switch. This switch when engaged (continuity) will only allow the RPM to be raised to a certain limit (set in the software). When released, you will have full RPM.

WIRE CONNECTIONS

To input wires into the PC6 fi rst remove the rubber plug on the backside of the unit and loosen the screw for the corresponding input. Using a 22-24 gauge wire, strip about 10mm from its end. Push the wire into the hole of the PC6 until it stops and then tighten the screw. Make sure to reinstall the rubber plug.

NOTE : If you tin the wires with solder it will make inserting them easier

INSTALLING THE POWER COMMANDER 6

FOR 2009-2010 MODELS

Remove the seat.
Remove the fuel tank.
Using the supplied Velcro, attach the PC6 to the inner side of the right hand side cover. Make sure to clean both surfaces with the supplied alcohol swab before attaching the Velcro.
Attach the ground wire from the PC6 with the small ring lug to the negative (-) terminal of the bike’s battery.
Route the PC6 harness towards the throttle body going underneath the frame support.
Unplug the stock wiring harness from the fuel injector.
Plug the PC6 wiring harness in-line of the stock wiring harness and fuel injector
Using the supplied Positap, attach the GREY wire from the PC6 to the stock ORANGE/BLACK wire of the stock wiring harness. This is the 3rd wire from the end, on the top row of the stock ECU connector.
Reinstall the fuel tank and the seat.

Download the latest map files from our web site at dynojet.com/tunes.

FOR 2011-2012 MODELS

Remove the seat.
Remove the fuel tank.
Using the supplied Velcro, attach the PC6 to the inner rear fender.
Make sure to clean both surfaces with the supplied alcohol swab before attaching the Velcro.
Attach the ground wire from the PC6 with the small ring lug to the negative (-) terminal of the bike’s battery.
Route the PC6 wiring harness towards the throttle body going underneath the frame support.
Unplug the stock wiring harness from the fuel injector.
Plug the PC6 wiring harness in-line of the fuel injector and the stock wiring harness.
Using the supplied Posi-tap, attach the GREY wire from the PC6 to the stock ORANGE/BLACK wire of the stock ECU connector. This is the 3rd wire from the end, on the top row of the ECU connector.
Reinstall the fuel tank and the seat. Download the latest map fi les from our web site at dynojet.com/tunes