HIKVISION DS-2CD2T45FWD Bullet Network Camera User Guide

HIKVISION DS-2CD2T45FWD Bullet Network Camera

Cautions&Warnings

These instructions are intended to ensure that the user cause the product correctly to avoid danger or property loss.

Laws and Regulations

The device should be used in compliance with local laws, electrical safety regulations, and fire prevention regulations.

Transportation
Keep the device in original or similar packaging while transporting it.

Power Supply
The input voltage should conform to the IEC60950-1 standard: SELV (Safety Extra Low Voltage) and the LPS (Limited Power Source). Refer to the appropriate documentation for
detailed information.
DO NOT connect multiple devices to one power adapter, to avoid over-heating or fire hazards caused by overload.
Make sure the plug is properly connected to the power socket.

System Security
The installer and user are responsible for the password and security configuration.

Battery
This equipment is not suitable for use in locations where children are likely to be present.
CAUTION: Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to the instructions
ATTENTION: IL Y A RISQUE D’EXPLOSION SI LA
BATTERIE EST REMPLACÉE PAR UNE BATTERIE DE TYPE INCORRECT. METTRE AU REBUT LES BATTERIES USAGÉES CONFORMÉMENT AUX INSTRUCTIONS
Improper replacement of the battery with an incorrect type may defeat a safeguard (for example, in the case of some lithium battery types). Do not dispose of the battery into fire or a hot oven, or mechanically crush or cut the battery, which may result in an explosion.
Do not leave the battery in an extremely high temperature surrounding environment, which may result in an explosion or the leakage of flammable liquid or gas.
Do not subject the battery to extremely low air pressure, which may result in an explosion or the leakage of flammable liquid or gas.

Maintenance
If the product does not work properly, please contact your dealer or the nearest service center. We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.
A few device components (e.g., electrolytic capacitor) require regular replacement. The average lifespan varies, so periodic checking is recommended. Contact your dealer for details.

Cleaning
Please use a soft and dry cloth when clean inside and
outside surfaces of the product cover. Do not use alkaline
detergents.

Using Environment

• When any laser equipment is in use, make sure that the

•  device lens is not exposed to the laser beam, or it may burn out.

• DO NOT expose the device to high electromagnetic radiation or dusty environments.For indoor-only device, place it in a dry and well-ventilated environment.

• DO NOT aim the lens at the sun or any other bright light.

• Make sure the running environment meets the requirement of the device. The operating temperature shall be -30 °C to 60 °C (-22 °F to 140 °F), and the operating humidity shall be 95% or less (no condensing).

• DO NOT place the device in extremely hot, cold,

• dusty or damp locations, and do not expose it to high electromagnetic radiation.

• White Light Illuminator (If supported)

• Possibly hazardous optical radiation emitted from this product.

• DO NOT stare at the operating light source. May be harmful to the eyes.

• Wear appropriate eye protection or DO NOT turn on the white light when you assemble, install or maintain the camera.
  Emergency

• If smoke, odor, or noise arises from the device, immediately turn off the power, unplug the power cable, and contact the service center.

• Time Synchronization Set up device time manually for the first time access if thelocal time is not synchronized with that of the network. Visit the device via Web browse/client software and go to time settings interface.
  Installation

• This camera series shares a similar structure. We take one type among this series for demonstration.

• Make sure the device is firmly secured to any wall or ceiling mountings.

• Be sure that there is enough space to install the device and accessories.

• Make sure that the device in the package is in goo condition and all the assembly parts are included.

• Make sure that the wall is strong enough to withstand at least 4 times the weight of the device and the mount.

• The standard power supply is 12 VDC or PoE, please make sure your power supply matches with your device.

• Make sure that the power has been disconnected before you wire, install, or disassemble the device.

• Make sure that no reflective surface is too close to the device lens. The IR light from the device may reflect back into the lens causing reflection.

• CAUTION: Hot parts! Burned fingers when handling the parts. Wait one-half hour afte switching off before handling parts. Thi sticker is to indicate that the marked item can be hot and should not be touched without taking care. For device with this sticker, this device is intended for installation in a  restricted access location, access can only be gained by service persons or by users who have been instructed about the reasons for the restrictions applied to the location and about any precautions that shall be taken.

Symbols and Marks

INSTALLATION

Interface Introduction

OPERATION

Activate and Access Network Camera
Scan the QR code to get Activate and Access the Camera. Note
that mobile data charges may apply if Wi-Fi is unavailable.

Reset and Restore Camera
Press Reset button for about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
For the position of the reset button, refer to the figure in the interface introduction page.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>