GoPro Volta BATTERY GRIP TRIPOD REMOTE User Guide

GoPro Volta BATTERY GRIP TRIPOD REMOTE

The First Step
You may need to upgrade your camera’s software before you can use Volta. For step-by-step instructions, go to gopro.com/update.

The Basics

Volta (Battery Grip/Tripod/Remote)

1. Swiveling Camera Mounting Fingers
2. LED Battery/Camera Status Indicators
3. Bluetooth® Button
4. Flip-Out Mounting Fingers
5. Mode + Power Button
6. Tripod Legs
7. 1/4-20 Mount
8. Camera Cable
9. Battery Status Button
10. Shutter Button
11. USB Charging Port (Under Port Cover)
12. Lanyard Attachment Point

Charging Volta

1. Flip open the USB charging port cover.
2. Insert the included USB cable into the port. Connect the other end of the cable to a USB power source.
3. Push the Battery Status button to start charging.

The blinking LED shows the battery status while Volta is charging. All LEDs will be lit when the battery is fully charged. Press the Battery Status button to check the charge level when Volta is not charging.

LED Power Indicators

TECH SPECS

• Battery capacity: 4900 mAh
• Power input: 5VDC / 3A (15W max)
• Power output: 5VDC / 2.4A (12W max)
• Charge time: 2.5 hours with GoPro Supercharger (sold separately) or other 5V / 3A charger.

A fully charged Volta will triple a fully charged camera’s normal battery life. Battery life may vary based on usage and other external conditions.

CAUTION : To keep Volta weather resistant, be sure the USB port cover is fully closed and the seal is tight after charging.

Mounting Your GoPro

INSTALLING THE USB PASS-THROUGH DOOR
Replace your camera’s standard door with the included USB Pass-Through Door.

1. Unlock the latch and flip the door open.
2. With the door in the horizontal position, gently pull outward until the door  snaps off.
3. Line the USB Pass-Through Door up with the small silver bar.
4. Press the door tightly into the small silver bar until it snaps into place and is  securely attached.

WARNING: Using the USB Pass-Through Door with the Volta camera cable plugged in will protect Volta and your camera from rain and snow, but is not waterproof. Using the USB Pass-Through Door underwater with your GoPro will damage your camera and void the warranty.

ATTACHING YOUR CAMERA

1. Mount your GoPro to Volta using the top mounting fingers.
   Heads Up: Be sure to insert your camera into the mounting fingers with the USB Pass-Through Door on the side opposite the Thumb Screw. Rotate the mounting fingers if needed to ensure that your camera is mounted properly.

2. Plug Volta’s USB cable into your camera.

3. Press the Battery Status button to start sending power to your camera.

Using Volta to Control Your GoPro
Volta can be used to control your GoPro whether its mounted or detached from the grip. Be sure set up wireless control now so you can simply detach your GoPro anytime you see a great shot that needs a wireless setup.

WIRED CONTROL
Volta’s integrated camera buttons gives you easy one-hand control of your GoPro.

1. Press the Battery Status button to wake Volta.
2. Press Volta’s Mode + Power button to turn your GoPro on.
3. Press Volta’s Mode + Power button button repeatedly to cycle to the mode that you want.
4. Press Volta’s Shutter button to start capturing.
5. To stop capturing video or time lapse, press Volta’s Shutter button again.
6. Press and hold Volta’s Mode + Power button button to turn your GoPro off.

WIRELESS CONTROL
Use Bluetooth to turn Volta into a wireless remote. Wireless control is also used to control your GoPro if you’re using Volta with Media Mod. Detach your GoPro from Volta and follow these setup instructions:

1. On your camera, complete these steps:
2. From the rear screen, swipe down to access the Dashboard.
3. Swipe left, and then tap Connections > Connect Device > Volta.
4. Press and hold the Bluetooth button on Volta for 4 seconds. Your camera will automatically begin pairing. Volta’s center LED will blink blue while it’s searching for the camera and turn solid blue when it’s connected

After pairing, Volta and your camera will wirelessly connect automatically when they are both on and not connected via the camera cable.

PRO TIP : After detaching your GoPro, plug Volta’s USB cable into the charging port to keep it out of the way

WARNING : Volta is not weather resistant when used as a wireless remote or any time the USB-C cable is disconnected from your camera.

Tripod

Flip out the built-in tripod legs any time you need to set Volta down to capture stationary shots. You can swivel or tilt your camera to adjust the capture angle.

PRO TIP : Volta’s additional battery power and tripod legs make it great for capturing extra-long time lapse shots.

Mounting Volta

RETRACTABLE MOUNTING FINGERS
Press the mounting finger release button to use Volta’s retractable mounting fingers. They make it easy to attach Volta to GoPro backpack straps, and other mounts

1/4-20 MOUNT
Volta has 1/4-20 mount built into its base for added mounting flexibility.

LANYARD
Use the hole in Volta’s base to secure the included wrist lanyard.

Using Volta with Media Mod
Insert your GoPro into Media Mod (sold separately) as you normally would and follow these steps:

1. Use your camera’s mounting fingers to attach your GoPro to Volta.
2. Plug Volta’s USB-C cable into the USB-C port on the back of your Media Mod.
3. Connect Volta to your camera via Bluetooth to use Volta’s built-in camera controls.

Resetting Volta

Press and hold the Mode + Power button and Shutter button simultaneously for 8 seconds if you need to reset Volta. Heads Up: You will not have to re-pair your camera if you reset Volta.

Notes
Here are a few important things to keep in mind while you’re using Volta:

• Volta will enter power save mode if it is not used for 24 hours. Press any button to wake it up.
• Disconnect Volta’s Bluetooth connection to your camera if you want to connect your camera to the GoPro Quik app. Press Bluetooth button to disconnect.
• Volta can only pair and connect to one camera at a time.
• Volta’s operating ambient temperature range is 14° F – 95° F (-10° C – 35° C). It’s normal charging temperature range is 32° F – 95° F (0° C – 35°C). Volta will automatically shut down if it’s too hot or too cold. The LEDs will blink red 4x to show that it needs to return to its normal operating temperature before the camera control buttons and camera charging will work. You can check its status by pressing any button. The LEDs will blink red if it’s not ready.

WARNING : Volta is not waterproof. Using it under water will damage both Volta and your camera

Regulatory Information
To see additional information regarding country certifications, refer to the Important Product + Safety Instructions included with your remote. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc., and any use of such marks is under license.

References

• GoPro | Official Camera of Fun | Shop Now & Save
• Product Updates

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>