GLOBAL INDUSTRIAL 168111 Portable Flexible and Expandable Conveyor Instruction Manual
- June 5, 2024
- GLOBAL INDUSTRIAL
Table of Contents
GLOBAL INDUSTRIAL 168111 Portable Flexible and Expandable Conveyor
It is the responsibility of the assembler/user to completely read and understand all instructions and safety information before proceeding with assembly. Following these instructions will ensure proper function and safety.
SAFETY INFORMATION
DANGER
- Do not put hands on scissor supports.
CAUTION
- The conveyor is very heavy. Assembly requires more than two people to prevent injury.
- Clean the conveyor regularly to maintain its lifespan.
WARNING
- Do not overload. Maximum capacity: 175 lb per foot.
- Keep the casters breaks down while in use.
- Do not stand up on top of the unit.
- The conveyor is not a toy. Not for use by children.
- This product contains chemicals that are known by the state of California to cause cancer, birth defects or other reproductive harm.
SPECIFICATIONS
Model
| Wheel Material| Effective Width in.| Overall Width in.|
Retracted Length ft.| Extended Length ft.| Lowest Height in.|
Highest Height in.| Load Cap. lb./ft. 2
---|---|---|---|---|---|---|---|---
| —| w| W| l| L| h| H| —
168110| Nylon| 18| 23.6| 7.2| 22.6| 27.6| 39.4| 175
168111| Nylon| 24| 29.5| 7.2| 22.6| 27.6| 39.4| 175
168112| Steel| 18| 23.6| 7.2| 22.6| 27.6| 39.4| 175
168113| Steel| 24| 29.5| 7.2| 22.6| 27.6| 39.4| 175
Component
Model
| Component Model No.| ****
Description
---|---|---
168110| | 330CP118| 18″ Nylon Skate Wheel Expandable Conveyor (Body only)
330CP122| 18″ Expandable Conveyor Leg Kit
168111| | 330CP119| 24″ Nylon Skate Wheel Expandable Conveyor (Body only)
330CP123| 24″ Expandable Conveyor Leg Kit
168112| | 330CP120| 18″ Nylon Skate Wheel Expandable Conveyor (Body only)
330CP122| 18″ Expandable Conveyor Leg Kit
168113| | 330CP121| 24″ Nylon Skate Wheel Expandable Conveyor (Body only)
330CP123| 24″ Expandable Conveyor Leg Kit
COMPONENTS CONTENT
| Component | Content | Key | Quantity |
|---|---|---|---|
| Skate Wheel Body | Conveyor body | 1 | 1 |
Skate Wheel Leg
| | Leg support| 2| 7
Swivel caster with brake| 3| 8
Swivel caster without brake| 4| 6
Box stop/Handle| 5| 1
Hex Key| H1| 1
Leg knob| H2| 14
Box Wrench| H3| 1
CAUTION Conveyor is very heavy. Assembly requires more than two people to prevent injury.
Installations
- Lay conveyor body (1) upside down on a level surface. Loosen all set screws with hex key (H1) provided.
- Insert leg supports (2) into sockets making sure threaded bosses are facing same direction.
- Retighten all set screws with hex key (H1) provided.
- Insert caster leg assemblies (3 & 4) into leg supports.
- Insert and tighten all knobs (H2) into caster posts.
- To install the box stop loosen and remove hex nuts (H5), washers (H4), and axle rod (6).
- Attach box stop handle (5) to end of the conveyor. Insert axle rod (6). Replace washers (H4) and retighten nuts (H5) with box wrench provided (H3).
- To use the handle (5) as a box stop, lift the horizontal bar and hook it to the top rod.
- Set pitch and height as required by adjusting caster legs up or down.