Finder IB1C91 Bliss wifi CHRONO THERMOSTAT User Manual

Finder IB1C91 Bliss wifi CHRONO THERMOSTAT

TECHNICAL FEATURES

• Power supply: 4 alkaline batteries 1.5V type AA
• Temperature adjustment WINTER: (+5…+37)°C
• Temperature adjustment SUMMER: (+5…+37)°C
• Resolution: 0.1°C
• Tolerance: +/– 0.5°C at 20°C
• Differential: Self-adjusting by product and adjustable by APP
• Operation mode: Summer – Winter – Auto – Manual – OFF
• Degree of protection: IP20
• PIN lock: yes, by Finder Bliss App
• Output: 5 A 250 V AC volt-free changeover contact
• Mounting: Wall

DIMENSIONS

INSTALLATION NOTES

SAFETY REQUIREMENTS

The installation and assembly of electrical equipment must be performed by expert personnel. Before connecting the Chrono thermostat make sure that the load (pumps, valves, boiler, etc …) is not powered-up and are within the rating of the contact.

• To remove the base use the appropriate slots 1 and 2

POSITIONING

• Install the chrono thermostat away from heat sources (radiators, direct sunlight, kitchens) and doors/windows. Mount about 1.5 meters above floor level.

FIXING

• Use screws 0 3.5 mm MAX – maximum head thickness 3 mm.
• When fastening, do not over-tighten the screws to avoid distorting the base.

CLEANING

• Use only a damp cloth for cleaning.

INSTALLATION

• Fix the base on the wall and make the electrical connection as shown on the diagram

NOTE: When using the chrono thermostat with the external power supply, the batteries MUST be removed.

• Insert the batteries into the battery compartment, respecting the indicated polarities.

CAUTION: Incorrect battery polarity can cause the batteries to leak acid and damage the chrono thermostat, invalidating the guarantee.

• Fix the chrono thermostat on its base as shown in the figure below

NOTE: To disassemble it, proceed in reverse.

BATTERY

The Chronothermostat is provided with 2 battery thresholds: the first threshold indicates that the batteries are low and must be replaced. In this condition, and with the display in the off state, a flashing battery icon will be seen every 5 seconds.

• After touching the Finder button and turning on the display, the battery icon will continue to flash.
• At the second threshold the Chronothermostat turns off, in this condition the flashing battery icon can be seen every 5 seconds (until the batteries completely run out).
• If the chrono thermostat is not connected to the Wi-Fi, after replacing the batteries reset the date and time.

POWER ON THE DISPLAY

CHRONOTHERMOSTAT OFF

DESCRIPTION OF KEYS AND SYMBOLS

DATE AND TIME SETTING

NOTE: After setting the year, the Chrono thermostat automatically recognizes the day of the week and automatically a number from 1 to 7 will appear on the display to indicate the day of the week.

NOTE

• At each programming step, it is possible to go back one step using the back button.
• Holding down the Finder button for 2 seconds saves and exits (returning to the main menu).

MANUAL PROGRAMMING

• To exit the manual setting and return to the main screen, press the “hand” button.

WEEKLY PROGRAMMING

• Press the numbers corresponding to the days of the week to be programmed (1 = Monday … 7 = Sunday). At the end of the selection, press the Finder key.
• The screen indicates that the temperature will be programmed (right) at the time indicated on the left.
• Set the desired temperature with the cursor at the indicated time (in this case between midnight and one in the morning). Press Finder to confirm the schedule and move to the next hour.
• Set the desired temperature with the cursor at the indicated time (in this case between one and two in the morning). Press Finder to confirm the schedule and move to the next hour.
• Proceed in the same way until reaching the 23:00 Hour time period.

NOTE

• To go back to the previous step, use the back button or the Finder button to switch to the next time programming.
• To exit programming and save the values set so far, press the Finder button for 2 seconds.

COPY PROGRAM

• To copy the program of one day to use for another day (s), simply press the day to be copied first and then the day (or days) on which to obtain the same programming.
• Then press the Finder button for 2 seconds to confirm and return to the main menu.

PROGRAM REVIEW

Example: reviewing day 3 (Wednesday)

• Repeatedly press the Finder button to step through and display the hours together with the appropriate set temperature.
• To go back to the previous step use the back button.
• Press the Finder button for 2 seconds to save and exit the review.

OFF STATE & FROST PROTECTION FUNCTION

• When the chrono thermostat is off, the display will show the word OFF.
• But in this condition, the frost protection function remains active.
• If the room temperature falls below the frost protection temperature, the flame icon will appear together with the word OFF.

SUMMER-WINTER SETTING

UNLOCKING CHRONOTHERMOSTAT – PIN

• The Chrono thermostat can only be locked using the Finder Bliss application.
• When the lock mode is activated, the Chronothermostat will display a lock icon.
• To unlock the Chrono thermostat you will need to enter the PIN as shown below

Caution

• By entering an incorrect PIN code, the Chronothermostat will display Err for an instant and then propose a re-try.
• After entering the wrong PIN 3 times, the chronothermostat will remain lockedM for 20 seconds with the word Err displayed (the display will turn off after 5 seconds to reduce battery drain).
• This procedure repeats for any further attempt to enter the wrong PIN.

NOTE

• Removing the batteries will not cancel the lock.
  If you forget your PIN, use code 618 to unlock the product.

PAIRING WITH PHONE

• Download the Finder Bliss application to your smartphone.
• The pairing procedure will be described in the application.
• Turn on Wi-Fi and search for a network
• In the case where the APP credentials were not inserted by the expiry of the timeout, the Chronothermostat performs a RESET of the configuration and the internal Wi-Fi is turned off.

CHRONOTHERMOSTAT Wi-Fi CONNECTION TO THE NETWORK

• After connecting the timer-thermostat to the home network, the update will take place within 4 to 40 minutes, depending on the update time set on the application.
• To immediately connect the chronothermostat to the App, with display off, press the Finder button for 3 seconds.
• Segments will appear to indicate waiting for parameters to be synchronized with the APP.

If the wait for synchronization persists for too long it means that the chronothermostat has difficulty updating with the cloud (via the APP). The problem may be due either to the poor network signal (seen by the Chronothermostat) or to a slow home connection, busy broadband, or slow server response. Battery life depends greatly on connection times. After 20 seconds, if the connection has not occurred, an error message appears (see page 18). If there was a previous connection to the Cloud the chronothermostat will display the last setting received from the server.

GENERAL CHARACTERISTICS

Type| Wi-Fi wall-mounted weekly programmable thermostat
Wi-Fi frequency| 2.4 GHz
Encryption| WPA2 / PSK
Display| LED
Resolution| 1 hour (1 minute via APP ***** )
Daylight Saving Time| Automatic Update
Battery life| About 1 year (Over 1 year depending on the model set by APP)
Functions| Additional settings available on the APP

• The time slot can not start and end at the same time

DEFAULT PARAMETERS

Season set| Winter
Frost protection| Fixed at 5°C
Thermal differential| 0.2°C

TROUBLESHOOTING

• Depending on the chronothermostat version, special characters such as “&”!”“.”_”/” may not be detected.

• In this case, replace the router name (SSID) using letters and numbers. Same for the password.

• The chronothermostat connects exclusively to 2.4 GHz networks. In the case of routers covering from 2.4 to 5 GH z it may in some cases be necessary to separate the two frequencies, then name an SSID for 2.4 GHz and one for 5 GHz.

• Wi-Fi signal repeaters may in some cases reduce the BLISS operation. If you have problems, try moving it near the router.

• The router must support WPA2 encryption.

• BLISS does not work on corporate networks (enterprise networks).

• Respect uppercase, lowercase letters and special characters in the SSID and password.

• Remove any empty spaces inserted inadvertently at the end of the data entered.

INDICATION OF ERRORS (ACCORDING TO VERSION)

ER0 GENERIC ERROR
ER1 INTERNET FAILURE

ADSL off / WiFi too distant / WiFi traffic congested / Network name SSID or PW incorrect

ER2 DATA CONNECTION WAS MADE BUT BLISS DID NOT RECEIVE AN ANSWER

Unstable or congested data traffic /

Communication problems with a reception from the cloud

ER3 DATA RECEIVED CORRUPTED

Connection failure during communication with the cloud / Very disturbed line

ANTENNA SIGNAL

On the APP it is advisable to check for a BLISS signal of at least 3 notches to ensure a good operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>