finder 1C.B1.9.005.0007 Digital Room Thermostat User Manual

: June 6, 2024
: finder

finder 1C.B1.9.005.0007 Digital Room Thermostat

TECHNICAL SPECIFICATION

Power supply:	3×1.5 V alkaline batteries type AAA – LR03
Temperature adjustment: (+5…+37)°C
Resolution:	0.1°C
Degree of protection:	IP20
Output: 5 A 250 V AC changeover volt-free contact Mounting:	Wall

INSTALLATION NOTES

SAFETY REQUIREMENTS
The installation and assembly of electrical equipment must be performed by experienced personnel. Before connecting the thermostat, make sure that the load (pump, valve, boiler, etc.) is not powered and that it falls within the thermostat’s contact rating.

POSITIONING
Install the thermostat away from heat sources (radiators, direct sunlight, kitchens), away from doors/windows, and mount approximately 1.5 meters above floor level.

FIXING BASE TO WALL

First, detach thermostat from its base by inserting two fingers into the central rear hole and, with the other hand, pull the front of the thermostat towards you.

FIXING BASE
Secure the Smart Bliss2 thermostat base to the wall using the screws included in the package. When fixing, be careful not to over-tighten the screws to avoid damaging the base.

ELECTRICAL CONNECTIONS

To make the connections, first refer to instructions for your heating system (pump, valve, boiler, etc.), then remove the terminal cover and connect the appropriate wires to terminals 6 (COM) and 7 (NO) of the Smart Bliss2 thermostat.

Type 01C.02.8.230.0500: OPTIONAL power supply
Using the external power supply, the batteries MUST be removed.

BATTERY INSERTION AND MOUNTING THE THERMOSTAT

Insert 3 x 1.5V alkaline batteries type AAA – LR03, paying attention to the indicated polarity. After inserting the batteries, initialization screens will appear. Wait for this process to finish and the detected temperature will then appear.
Mount the thermostat to its base by first engaging the bottom part of the thermostat with the lower pins of the base plate, then close the upper part of the thermostat to lock onto the upper pins.

The thermostat is now ready to be configured.
However, the Gateway2 (1Y.GU.005.1) must first be installed.

GATEWAY2 INSTALLATION

Connect the Micro USB connector to the Gateway2 (1Y.GU.005.1) and plug the power supply into to the elecrical outlet.

After switching on, the luminous base of the Gateway2 flashes with a fading white light – which indicates it is awaiting configuration.

CONFIGURATION

To configure the Gateway2 and the Smart Bliss2 Thermostat, download the Finder Bliss application from the Google Play Store or the Apple Store and proceed with the configuration following the tutorial on the App. When requested by the App, activate the association of the thermostat following the following screens:

When done, the temperature detected by the Smart Bliss2 thermostat will bedisplayed in the application.

THE LUMINOUS BASE – NOTES

WHITE LED
– Fading flashing: waiting for configuration
– Fixed: Wi-Fi network and Cloud connection present
– 2 Flashes: Connected to the Wi-Fi network but no connection to the Cloud (Check your Internet connection)
– 3 Flashes: No connection to the Wi-Fi network and no connection to the Cloud (Check your Wi-Fi network)
BLUE LED
– Flashing: sending Bluetooth commands
RED LED
– Flashing: sending commands to the Smart Bliss2 Thermostat

|

OVERVIEW OF SCREENS & ICONS 3

ROOM TEMPERATURE
Thermostat is set to AUTOMATIC mode (AUTO) and will respond to programming via the App. Current room temperature is displayed.

TARGET TEMPERATURE IN MANUAL MODE
The thermostat is set to MANUAL mode. The target temperature is displayed.

MANUAL MODE
Thermostat is set to Manual mode.If the small arc segment at the top is coloured, the heating or cooling system is active. If red – heating If blue – cooling.

HOURS SETTING
This displays the number of hours for which the manual mode is to apply. From 1 hour (h01) to permanent (h∞).

FULL ARC
Appears when a setting is accepted and when the heating or cooling system is active.

HUMIDITY DETECTED IN THE ATMOSPHERE
In this section you can opt to view the level of humidity in the atmosphere (% RH).

%RH
Display of Relative Humidity currently present in the atmosphere.

ON/OFF SECTION
In this section you can turn the thermostat ON or OFF.

ON MODE
With ON mode selected, the thermostat can function in either AUTO or Manual modes.

OFF MODE
With the OFF mode selected, the thermostat will still maintain a frost protection setting of + 5°C to avoid freeze damage to the system.

SETTINGS MENU
From here you can access the device settings.

ASSOCIATION WITH THE GATEWAY
The opposing arrows will flash only during the gateway pairing procedure.

TRANSMISSION TEST WITH THE GATEWAY
At this point in the menu you can perform a signal transmission test between the gateway and the thermostat.

RESULT OF THE TRANSMISSION TEST WITH THE GATEWAY
0 SIGNAL ABSENT: the gateway is unreachable
1/6 POOR: bring the two devices closer
7/8 GOOD: make changes only if errors are found
9/10 VERY GOOD: stable connection.

FIRMWARE VERSION
At this point in the menu it is possible to view the firmware version present on the device.

MANUAL MODE

ON/OFF MODE

AUTOMATIC (AUTO) MODE

HUMIDITY

ASSOCIATION WITH THE GATEWAY

BEFORE FOLLOWING THE ASSOCIATION PROCEDURE, OPEN THE BLISS APP AND ADD A NEW DEVICE

TRANSMISSION TEST WITH THE GATEWAY

HEATING/COOLING

ACCORDING TO THE OPERATING MODE OF THE THERMOSTAT, YOU WILL SEE DIFFERING VISUAL FEEDBACKS ON THE LUMINOUS ARC

HEATING
THE ARC IS RED

COOLING
THE ARC IS BLUE

GATEWAY SET-UP

FIRST STEPS
Connect the gateway to the socket using the micro USB power supply before starting the procedure

The gateway works only with 2.4GHz Wi-Fi networks. Check that you have a 2.4GHz network configured on your home router and that you have the network name and password before starting the procedure

After logging in to the new Bliss app, click on “Add device” to start the association

Select “Bliss2” to star the association of the gateway and the thermostat

Select an existing house (created with Yesly) or create a new one to define which system the gateway belongs to. Then press “Continue”.

Select the time zone you are in. The default is for Italy

Select “Configure a new gateway” and give it a name. Then press “Continue”.

fter selecting the gateway to associate, choose to connect it to the Wi-Fi network. Then press “Continue

You can choose whether to associate the gateway to the network by selecting it from those available or by scanning the QR code located behind the router.

After choosing the network to associate with, the gateway will complete the association.

Now you need to put the Bliss2 thermostat in “connection” mode. Go to the device and make the arrows blink.

Execute this procedure on the Bliss2:

The gateway is now communicating with the Bliss2. Please, wait.

When the procedure is over, give the Bliss2 a name

Finder Bliss2 is properly paired. Now all you have to do is configure the temperature schedule and discover the rest of the functions of your new Smart Bliss2 Thermostat.

FINDER P.L.C.
Opal Way – Stone Business Park
STONE, STAFFORDSHIRE
ST15 0SS- UK
Tel: +44 (0)1785 818100
Fax: +44 (0)1785 815500
finder.uk@findernet.com