SEALEY LP14 Infrared Gas Heater Instructions
- June 5, 2024
- SEALEY
Table of Contents
LP14 Infrared Gas Heater
INSTRUCTIONS FOR:
INFRARED GAS HEATER
Model No: LP14
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will if used according to these instructions and properly maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS
INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
SAFETY INSTRUCTIONS
1.1. GENERAL SAFETY
IMPORTANT: The LP14 is a mobile, propane-fired, unvented, infrared space
heater for commercial applications only. DO NOT use domestically.
WARNING! Use only in well-ventilated spaces of more than 15m 3 to prevent
an accumulation of dangerous combustion gases.
DO NOT operate heater in basements or otherwise below ground level.
WARNING! The heater will become very hot during use.
WARNING! Ensure Health & Safety, local authority, and general workshop
practice regulations are adhered to when using this equipment.
Familiarise yourself with the application and limitations of the heater, as
well as the potential hazards.
WARNING! Disconnect the heater from the gas supply before performing any
maintenance.
Maintain the heater in good condition (use an authorized service agent).
Replace or repair damaged parts. Use genuine parts only. Unauthorized parts
may be dangerous and will invalidate the warranty.
WARNING! Keep all guards and holding screws in place, tight, and in good
working order. Check regularly for damaged parts. A guard or any other part
that is damaged must be repaired or replaced before the heater is next used.
Keep the heater clean for the best and safest performance.
Ensure the propane bottle is in a stable upright position before igniting the
heater. DO NOT use the bottle in any position other than upright.
DO NOT use any fuel other than propane.
Ensure there are no flammable or combustible materials within 2 meters of the
heater and that nothing, including walls, is less than 500mm from any surface
of the heater.
DO NOT use the heater where there are flammable liquids, solids, or gases
such as paint solvents, etc.
Keep gas hose away from heat, oil, and sharp edges. Regularly check the hose
for wear and ensure that all connections are secure.
DO NOT move the heater when it is operating.
DO NOT use the heater for any purpose other than that for which it is
designed.
DO NOT operate the heater if any parts are damaged or missing as this may
cause failure and/or personal injury.
DO NOT adjust, or tamper with, the regulator.
DO NOT allow untrained persons to operate the heater.
DO NOT operate the heater when you are tired or under the influence of
alcohol, drugs or intoxicating medication.
When not in use disconnect from the gas supply and store in a safe, dry,
childproof area.
In the event of a gas leak immediately close the bottle valve, extinguish any
flame and then place equipment in a well-ventilated area,
preferably outdoors, and away from any heat sources (including strong
sunlight). Rectify the cause of leakage.
If a persistent leakage occurs notify a qualified service engineer.
DANGER! If the burner remains alight after the bottle valve has been
closed DO NOT attempt to remove the burner and/or regulator from the bottle.
Contact your gas supplier immediately.
INTRODUCTION & SPECIFICATION
Ceramic plaque type heater. Steel tube stands with a built-in handle. Heat
output from 9,200 to 17,000Btu/hr. Supplied with 1.5mtr hose and regulator.
DVGW Approved. Gas bottle not included.
Model No. . . . . . . . . . . . . . . . . . . . . . . . . . . . .LP14
Fuel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Propane
Output. . . . . . . . . . . . . . . . . . . . .9,200-17,000Btu/hr
Fuel Consumption. . . . . . . . . . . . . .0.216-0.400kg/hr
CONTENTS
3.1. Content
3.1.1. Check content against the list below and, in the event of shortages or
damage, contact your supplier.
Contents:
- Heater stand and mounting bolts
- Heater assembly
- Hose and gas bottle regulator
ASSEMBLY
4.1. Assembly (See fig.2)
4.1.1 Attach the stand to the heater assembly using the two bolts supplied.
4.1.2. Fit the regulator to the bottle by screwing the POL nut anticlockwise
into the port of the gas bottle valve. Tighten the nut with a spanner.
4.1.3. Attach one end of the gas hose to the threaded outlet on the regulator
(note that the fitting has a reverse thread). Attach the other end of the gas
hose to the threaded heater valve inlet (note that the fitting has a reverse
thread). Ensure the hose is routed so that it does not touch any part of the
heater, which will become hot during operation.
4.1.4. Open the bottle valve and, using soapy water, check all joints for
leaks.
OPERATION
WARNING! Ensure that you read, understand and apply the safety
instructions in Section 1.
5.1. Siting the heater.
5.1.1 DO NOT use the heater where there are flammable liquids, solids, or
gases such as paint solvents, etc. Ensure there are no flammable
or combustible materials within 2 meters of the heater and that nothing,
including walls, is less than 500mm from any surface of the
heater. Always ensure that the heater is facing away from the gas bottle.
5.2. Lighting heater
5.2.1 Open the gas bottle valve.
5.2.2. Push the heater control knob down and turn it anticlockwise to the
center (full on) position and keep it held down.
5.2.3. After a few seconds bring a flame up to the bottom edge of the burner.
5.2.4. After the gas ignites keep the knob held down for a further 20 seconds
then turn the control knob anticlockwise again to reduce the heat output to
the required level.
5.3. Turning off the heater
5.3.1 Turn the heater control knob clockwise to the full-on position then push
the knob down and continue to turn it clockwise to the off
position.
5.3.2. Close the gas bottle valve.
5.4. Changing the propane bottle
5.4.1. Ensure the bottle valve is closed and then unscrew the POL nut and
remove the regulator.
5.4.2. Fit regulator to new propane bottle. Check for gas leaks as in 4.1.4.
INFRARED GAS HEATER
Model: LP14
90/396/EEC Gas Appliance Directive
93/68/EEC CE Marking Directive
Declaration of Conformity We, the sole importer into the UK, declare that the product listed here is in conformity with the following standards and directives.
Signed by Mark Sweetman
Date 14th June 2007
The construction file for this product is held by the Manufacturer and may be
inspected, by a national authority, upon request to Jack Sealey Ltd.
For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Products.
NOTE: It is our policy to continually improve products and as such, we
reserve the right to alter data, specifications, and component parts without
prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will
be required for any claim.
INFORMATION: For a copy of our catalog and latest promotions call us on
01284 757525 and leave your full name, address and postcode.
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
01284 757500
01284 703534
www.sealey.co.uk
sales@sealey.co.uk Get In Touch
Call: 0845 6880112
Email: info@adremit.co.uk
Our Address
Prevent, Adremit Limited, Unit 5a, Commercial Yard,
Settle, North Yorkshire, BD24 9RH
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>