SEALEY VS9114 PANEL BAG SET 3PC Instruction Manual
- June 5, 2024
- SEALEY
Table of Contents
PANEL BAG SET 2PC
MODEL NO: VS9114
Instruction Manual
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT IS CORRECTLY
AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE AND/OR PERSONAL INJURY WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to the instruction manual
SAFETY
- WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
√ Familiarise yourself with the application and limitations of the panel bag
set, as well as the potential hazards.
√ Maintain the set in good condition.
√ Replace damaged parts.
Use genuine parts only. Unauthorized parts may be dangerous and will
invalidate the warranty.
√ Maintain correct balance and footing. Ensure the floor is not slippery and
wear non-slip shoes.
√ Keep children and unauthorized persons away from the working area.
× DO NOT put hands/fingers in apertures created by bags without first
inserting a mechanical chock to prevent accidental injury
× DO NOT use the panel bags for purposes other than those for which they were
designed.
×DO NOT over-inflate.
× DO NOT use on doors fitted with airbags.
× DO NOT use when you are tired, under the influence of alcohol, drugs, or
intoxicating medication.
√ Deflate bag prior to storage.
√ Store in a clean dry place.
INTRODUCTION
Multi-purpose durable air cushion devices with rigid edges and fine air control valve. Suitable for positioning panels, bonnets, and boots, prior to fitment. 2mm thickness and semi-rigid construction allows bags to be slid between the window frame and weather-stripping for improved access for emergency vehicle opening tools. A soft air cushion is gentle on paintwork, frame, beadings, and glass. Can also be used for positioning kitchen units, windows, and doors.
SPECIFICATION
Model No: …………………………………………………………VS9114
Load Capacity: ……………………………………………………. 135kg
Bag Dimensions (W x H): ……………………………..Refer to fig.1
Bag 1: ………………………………………………………128 x 270mm
Bag 2: ………………………………………………………150 x 165mm
Bag 3: ………………………………………………………115 x 190mm
Minimum/Maximum Thickness ………………………. 2mm-80mm
ASSEMBLY & INSTALLATION
4.1. TO ADJUST BODY PANELS
4.1.1. Place a panel airbag between the vehicle body and panel to be fitted
(bonnet, boot, etc.) at the point that needs adjusting.
4.1.2. Ensure the pump valve is closed (fully clock-wise), pump air into the
bag by squeezing the bulb on the pump, (taking care, not to over-inflate)
moving the panel to the required position.
4.1.3. When the panel has been fitted, simply deflate the panel bags by
turning the release valve anti-clockwise.
4.1.4. The rigid construction allows the bag to be inserted between a window
frame and weather stripping on a vehicle door etc. To ease this operation,
first, lubricate the bag with a water-soluble lubricant such as washing up
liquid. When using the bag to gain access through a door etc., ensure that a
mechanical means of chocking the door is employed before inserting fingers or
hands, etc.
MAINTENANCE
5.1. When the bags are not in use ensure they are deflated, clean, and stored
in a dry location.
5.1.1. Inspect before use to check for any sign of damage. The bags cannot be
repaired; any sign of damage must result in the bag being discarded.
ENVIRONMENT PROTECTION
**** Recycle unwanted materials instead of disposing of them as waste. All
tools, accessories, and packaging should be sorted, taken to a recycling
center, and disposed of in a manner that is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain
any fluids (if applicable) into approved containers and dispose of the product
and fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications, and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
© Jack Sealey Limited
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>