SEALEY SDL14 30W LITHIUM-ION RECHARGEABLE PLASTIC WELDING REPAIR KIT User Manual
- June 5, 2024
- SEALEY
Table of Contents
30W LITHIUM-ION RECHARGEABLE PLASTIC
WELDING REPAIR KIT
MODEL NO: SDL14
User Manual
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
SAFETY
1.1. GENERAL SAFETY
- WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
√ Familiarise yourself with the application, limitations, and potential
hazards of the device.
√ Replace or repair damaged parts. Use genuine parts only. Unauthorized parts
may be dangerous and will invalidate the warranty.
√ Locate the device in a suitable working area and keep the area clean and
tidy, and free from unrelated materials.
√ Keep the work area clean, and uncluttered and ensure there is adequate
lighting.
√ Keep the device clean for the best and safest performance.
√ Ensure there are no flammable or combustible materials near the work area.
√ Wear approved safety eye protection (standard spectacles are not adequate).
√ Wear heat-resistant gloves and appropriate protective clothing.
√ Ensure the workpiece is adequately held before operating the device.
√ Always use the stand provided when not using the hot tool so that the tip
cannot make contact with the work surface.
√ Always use the device in a well-ventilated atmosphere or alternatively wear
respiratory protection.
√ Ensure that when the device is put down during use that the tip is not near
to or in contact with any material that may burn or melt.
√ After use always keep the plastic welder in its original package in a safe
place away from children.
× DO NOT touch the staple or tip during its warm-up phase.
× DO NOT use in wet or damp conditions.
× DO NOT operate the device when you are tired or under the influence of
alcohol, drugs, or intoxicating medication.
× DO NOT leave the device hot and unattended. (If you are leaving the work
area even for a short period of time switch it off and allow it to cool.)
× DO NOT use the device for any purpose other than that for which it has been
designed.
× DO NOT allow untrained persons to operate the device.
× DO NOT touch the workpiece as it will be very hot. Allow cooling.
× DO NOT operate the device if damaged.
1.2. BATTERY SAFETY
- WARNING! To reduce the risk of burns or fire:
× DO NOT attempt to open, disassemble, modify or service the battery pack.
× DO NOT crush, puncture, short external contacts or dispose of in fire or
water.
× DO NOT expose to temperatures above 60°C (140°F).
√ Recycle or dispose of used batteries as stipulated by local regulation.
INTRODUCTION
Cordless and lightweight welding iron. Inbuilt LED to illuminate welding area in low light areas such as engine bays. Kit includes plastic welding tip, plastic welding with pipe guide tip, hot staple tip, plastic welding rods in ABS/PP/PE/PS, reinforcing mesh (x3), 0.8mm flat staples (x50), 0.6mm flat staples (x50), USB charging lead and safety stand. Heats up to a maximum temperature of 500°C.
SPECIFICATION
MODEL NO: ………………………………………………………SDL14
Battery: ………………………………………. 3.7V 2.4Ah Lithium-ion
Input: ……………………………………………………………….. 5V – 1A
Charging Time: ………………………………………………………3.5hr
Maximum Temperature: ……………………………………….. 500°C
Operating Time: ………………………………………………….. 40min
Power:…………………………………………………………………..30W
Staple Size: ………………………………………….. 0.6mm & 0.8mm
CONTENTS
OPERATION
5.1. TESTING MATERIALS TO BE WELDED:
5.1.1. Most adhesion failures are due to the incorrect matching of materials.
The welding rod therefore must be of the same material as the item to be
welded. For instance, most car body parts are made of ABS material.
Some manufacturers, however, use different plastics in their products. To
test, snip off a piece of material from the work to be welded and proceed as
follows:
▲ DANGER: Step 5.1.1 must be performed in a well-ventilated area (out of doors
if possible). Never perform tasks in a domestic building. Safeguard against
fire. Wear safety gloves and a face mask. DO NOT inhale smoke.
5.1.2. Set light to the sample with a naked flame. If the flame gives off
black smoke it is (almost) certain to be ABS.
5.1.3. By sample, take a strip of material from an unobtrusive part of the
component and use it as your welding rod.
5.1.4. If in doubt, contact the item manufacturer.
5.2. WELDING THE MATERIAL
5.2.1. Remove any paint or other covering from the entire adjoining surface
areas of the piece to be welded.
5.2.2. Cut a chamfer on adjoining pieces to form a groove that can be filled
with weld.
5.2.3. Thoroughly pre-heat both surfaces to be welded (they should be soft but
not tacky).
5.2.4. Attach tip 2 (fig.1.2) to position the tip over the material to be
welded and feed the welding rod through the slot at the same time moving the
device along the groove at a speed according to the melt/adhesion rate.
5.2.5. A good connection is made when a small dome forms (a trial is always
recommended using an odd piece of material). With practice, a good flat weld
can be achieved by applying pressure on the nozzle as the rod is drawn along.
Overlapping materials can be removed with a sharp knife.
5.3. WELDING PROBLEM CHECKLIST If a weld fails ask yourself the following
questions:
5.3.1. Do the materials match?
5.3.2. Are both surfaces clean?
5.3.3. Are surfaces chamfered?
5.3.4. Have surfaces been pre-heated correctly?
5.3.5. Did the welding rod melt to the correct consistency?
5.4. IMPORTANT NOTES.
5.3.1. To weld over cracks in the material, drill approximately 1/16” diameter
holes at each end of the crack to prevent running during welding and sanding.
5.3.2. Handling the welding tips – The tips get very hot and should only be
removed by the plastic base when cool enough to do so.
5.5. USING THE STAPLE ATTACHMENT (FIG 1.3)
5.5.1. Choose a suitable heating repair pin and place it on the tip of the
stapler.
5.5.2. Keep the stapler perpendicular to the damaged surface.
5.5.3. Press the switch button on the grip for 5 to10 seconds until the pin is
hot enough to weld. Then press the pin gently against the damaged surface.
5.5.4. When the pin is halfway into the plastic material stop pressing and
release the power button. Wait for a few seconds until the repair becomes
firm.
5.5.5. Once the plastic has cooled and the staple is fully secure, pull the
stapler gun gently back to release.
5.5.6. If the damaged surface is very long or wide, insert extra pins, 1/2
inch apart.
5.5.7. Cut off the pins with a side cutter, then grind the remains of the pin
with a sander/grinder.
× DO NOT press the repair pins too hard as it may penetrate the plastic
too far.
MAINTENANCE
√ When cold store in a safe dry place away from the reach of children.
ENVIRONMENT PROTECTION
** Recycle unwanted materials instead of disposing of them as waste. All
tools, accessories, and packaging should be sorted, taken to a recycling
center, and disposed of in a manner that is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain
any fluids (if applicable) into approved containers and dispose of the product
and fluids according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the
EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the
product is no longer required, it must be disposed of in an environmentally
protective way. Contact your local solid waste authority for recycling
information.
BATTERY REMOVAL**
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd
are required to inform potential purchasers of products containing batteries
(as defined within these regulations), that they are registered with Valpak’s
registered compliance scheme. Jack Sealey Ltd Batteries Producer Registration
Number (BPRN) is BPRN00705.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications, and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
© Jack Sealey Limited
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>