SEALEY CP108VCPBO 10.8V CORDLESS POLISHER User Manual
- June 5, 2024
- SEALEY
Table of Contents
10.8V Ø75MM CORDLESS POLISHER – BODY ONLY
MODEL NO: CP108VCPBO
User Manual
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to the instruction manual
|
Wear protective gloves
| Wear eye protection
| Wear face mask
|
Wear ear protection
---|---|---|---|---
SAFETY
Disconnect the polisher from the battery unit before changing
accessories, servicing, or performing any maintenance.
Maintain the polisher and battery in good condition. Check moving parts
alignment on a regular basis.
Replace or repair damaged parts. Use an authorized service agent and
recommended parts only. Unauthorized parts may be dangerous and will
invalidate the warranty.
Ensure the polisher is switched off before installing the battery pack.
Keep the polisher and charger clean for the best and safest performance.
Remove ill-fitting clothing. Remove ties, watches, rings, and other
loose jewelry and contain long hair.
Evaluate your working area before using the polisher e.g. ceilings,
floors and enclosures may contain electrical items or water piping.
Ensure the battery pack is correctly inserted into the polisher handle
and latched in place before attempting to switch on the polisher.
Secure loose workpieces with a clamp, vice, or another adequate holding
device.
Avoid unintentional starting.
Wear approved safety eye protection (standard spectacles are not
adequate).
Maintain correct balance and footing. Ensure the floor is not slippery
and wear non-skid shoes.
Keep children and unauthorized persons away from the working area.
Store the polisher and charger in a safe, dry, childproof area where the
temperature will not exceed 104°F (40°C).
DO NOT use the polisher where there are flammable liquids, solids, or
gases, such as paint solvents, etc.
DO NOT allow children to operate the polisher.
DO NOT operate the polisher if any parts are missing as this may cause
failure and/or personal injury.
DO NOT hold an unsecured workpiece in your hand.
DO NOT leave the polisher operating unattended.
DO NOT carry the polisher with your finger on the power switch.
DO NOT use the polisher for a task it is not designed to perform.
DO NOT operate the polisher when you are tired or under the influence of
alcohol, drugs, or intoxicating medication.
**** DO NOT get the polisher or battery wet or use it in damp or wet
locations.
INTRODUCTION
Compact, lightweight cordless polisher – body only. Comfortable housing with a soft grip to help reduce vibration. The variable speed control trigger makes this polisher very easy to use. Supplied with side handle and polishing pad. Requires compatible 10.8V 2Ah or 4Ah battery and mains charger, sold separately.
SPECIFICATION
Model No. ……………………………………………….CP108VCPBO
Battery ……………… 10.8V 2Ah-4Ah Lithium-ion (not included) Consumable parts (not
included)
………………………………………………….CP108VBP 2Ah Battery
………………………………………………..CP108VBP4 4Ah Battery
Free speed ……………………………………0-2600rpm/0-7800rpm
Noise power/pressure …………………………………… 91/80dB(A)
Vibration/rating ………………………………………. 4.7m/s²/1.5m/s²
Pad size ………………………………………………………….. Ø75mm
Replacement parts …………………CP108VMC – Mains charger
Thread size …………………………………………………………….. M6
OPERATION
4.1. Fit battery.
4.2. BATTERY CHARGE STATUS TEST
4.2.1. Press trigger, all LEDs lit: battery charged, one LED lit: battery
needs charging.
4.3. In order to maintain battery efficiency:
** DO NOT fully discharge. After every use fully charge the battery, charge
every 4 months even if the tool is not used.
‰ WARNING! Before use, ensure that you have read and understood Section 1
Safety Instructions.
4.4. To attach/remove the applicator pad, remove the battery, depress the
chuck lock button behind the chuck (fig.1), and screw/unscrew the applicator
pad.
4.5. Release the chuck lock button and check that the applicator pad is
locked into the chuck before switching it on.
4.6. Set the required speed by use of the speed selector switch (fig.1).
4.7. Unlock the drive lock (fig.1).
4.8. Fit and grip the side handle and start the polisher by gentle and
slow application of pressure on the trigger (fig.1).
4.9. Increase/decrease the speed of the polisher using the variable speed
control trigger (fig.1) to suit the task at hand.
4.10.** Ensure that the above features are working correctly prior to use.
MAINTENANCE
‰ WARNING: Always disconnect the battery before carrying out any inspection, maintenance, or cleaning.
5.1. GENERAL INSPECTION
5.1.1. Regularly check that all the fixing screws are tight.
5.1.2. Repairs should only be carried out by an authorized service
center.
5.2. CLEANING
‰ WARNING: Always wear protective equipment including eye protection and
gloves when cleaning this tool.
5.2.1. Keep your tool clean at all times. Dirt and dust will cause
internal parts to wear quickly and shorten the device’s service life.
5.2.2. Clean the body of your machine with a soft brush, or dry cloth.
5.2.3. Never use caustic agents to clean plastic parts. If dry cleaning
is not sufficient, a mild detergent on a mildly damp cloth is recommended.
5.2.4. Water must never come into contact with the tool. Ensure the tool
is thoroughly dry before using it.
5.2.5. If available, use clean, dry, compressed air to blow through the
ventilation holes (where applicable).
WARNING! – Risk of Hand Arm Vibration Injury.
This tool may cause Hand Arm Vibration Syndrome if its use is not managed
adequately.
This tool is subject to the vibration testing section of the Machinery
Directive 2006/42/EC.
This tool is to be operated in accordance with these instructions.
Measured vibration emission value (a): 4.7m/s²
Uncertainty value (k): 1.5m/s²
Please note that the application of the tool to a sole specialist task may
produce a different average vibration emission. We recommend that a
specific evaluation of the vibration emission is conducted prior to commencing
with a specialist task.
A health and safety assessment by the user (or employer) will need to be
carried out to determine the suitable duration of use for each tool.
NB: Stated Vibration Emission values are type-test values and are
intended to be typical.
Whilst in use, the actual value will vary considerably and depend on many
factors.
Such factors include; the operator, the task, and the inserted tool or
consumable.
NB: ensure that the length of leader hoses is sufficient to allow
unrestricted use, as this also helps to reduce vibration.
The state of maintenance of the tool itself is also an important factor, a
poorly maintained tool will also increase the risk of Hand Arm Vibration
Syndrome.
Health surveillance: We recommend a program of health surveillance to
detect early symptoms of vibration injury so that management procedures can be
modified accordingly.
Personal protective equipment: We are not aware of any personal
protective equipment (PPE) that provides protection against vibration injury
that may result from the uncontrolled use of this tool. We recommend a
sufficient supply of clothing (including gloves) to enable the operator to
remain warm and dry and maintain good blood circulation in fingers etc. Please
note that the most effective protection is prevention, please refer to the
Correct Use and Maintenance section in these instructions. Guidance relating
to the management of hand-arm vibration can be found on the HSC website:
www.hse.gov.uk – Hand-Arm Vibration at Work.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the
EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the
product is no longer required, it must be disposed of in an environmentally
protective way. Contact your local solid waste authority for recycling
information.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories, and packaging should be sorted, taken to a recycling center, and
disposed of in a manner that is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications, and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way,
Suffolk Business Park, Bury St Edmunds,
Suffolk. IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
CP108VCPBO Issue 2 (3) 06/06/22
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>