SEALEY TS01.V2 700MM VICE/BENCH MOUNTING SHEET METAL FOLDER Instruction Manual

SEALEY TS01.V2 700MM VICE/BENCH MOUNTING SHEET METAL FOLDER

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY

• Wear approved safety goggles, gloves, and footwear, when operating the folder. Your local Sealey dealer offers a complete range of safety equipment.
• Use the tool only for its intended purpose.
• Regularly check all parts of the folder for damaged parts. DO NOT use if any of its components are broken, worn, or damaged.
• Use original Sealey spare parts and accessories. Use of non-recommended spare parts may be dangerous and will invalidate the warranty.
• Ensure good footing, wear nonslip footwear.
• DO NOT operate this tool while under the influence of drugs, alcohol, or other impairing medication.
• DO NOT Allow unqualified persons to operate the metal folder. Keep children away from the tool.

INTRODUCTION

Bench and vice mounting sheet metal folder, fitted with mounting plates. Capable of bending a 2mm steel sheet, of limited length, up to and beyond a 90° angle. The unique patented endless design and removable folding plate allow the user to fold, channel and offset any length of sheet metal up to 1mm thick, by simply moving the sheet as required after each fold. With adjustable fold plate to help achieve the cleanest fold possible. Ideal for the small garage or restoration operation.

SPECIFICATION

• MODEL NO:…………………………………………………….TS01.V2
• Capacity:…………………………….. 20 Gauge Sheet, Ø1mm Rod

OPERATION

• Unpack the unit and check that all parts are included and not damaged. Should you experience a problem contact your supplier immediately.
• Position the folder on the bench where it is to be mounted, ensuring that the handles (fig.1.7) hang vertically over the front of the bench, and use foot plates (fig.1.6) as templates to drill holes in the bench, use appropriate fixings. Or clamp the folder in a vice.
• By using a center adjustment nut (fig.1.4) ensure the top and base plate are parallel, this may require adjustment from time to time.
• Release clamps (fig.1.1) at either end of the folder so that a mall test piece of sheet metal can be inserted between the top and base plates. (fig.1.3)
• Position the test piece, adjust the top plate by use of clamps (fig.1.1) lightly tighten, and use a spanner to adjust the cam (fig1.2), so that base and top plate are aligned.
• Ensure that there is even pressure on both ends.
• Raise the top folding plate (fig.1.3) by lifting handles to create the fold. From this test, you will be able to determine how and where the fold appears.
• When satisfied with the test results, proceed with the actual workpiece.
• By rotating the end clamps through the vertical axis, longer lengths of the metal sheet can be folded, i.e. fold a section, unclamp, move the sheet, reclamp, fold a second section, etc.

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories, and packaging should be sorted, taken to a recycling center, and disposed of in a manner that is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications, and component parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team at technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>