Hiseeu KHB58-P 4K PoE Camera User Guide

Hiseeu KHB58-P 4K PoE Camera

Hello,
Greeting from Hiseeu Team! Thank you for choosing our products and hope everything going well with you and your family. On behalf of all colleagues in Hiseeu, we sincerely appreciate your trust and support.
If there are any difficulties during operating our products, please feel free to contact us, we will do whatever we can to assist you.
The compatible NVR and PoE system (Hiseeu) are listed in the following table:

These models are powered by Hikvision. It’s compatible and able to connect with third-party devices via ONVIF protocol. (As long as the third-party device is ONVIF compatible).
Any questions, we are ready to help.
Best Regards
Hiseeu Team
Email: Love@hiseeu.com
Tel: +1 {917) 688 2228

Reset the Camera

We highly recommend rest the camera before installation. Steps:

1. Power on the camera properly.
   (You can power it on with PoE NVR/Switch, or extra power adapter 12V1A)

2. Unscrew camera housing with the screw provided.

3. Press and hold the reset button until you see the infrared light turns on.

4. It will restore all parameters to default settings.
   X: When working with Hiseeu 4K PoE NVR system, NVR will activate the camera and auto-connect it. Plug and Play, no need for configuration.

Activate Camera

The camera needs to be activated by setting a strong password before use. This part introduces camera activation using different client tools.

Activate via SADP
SADP is a tool to detect, activate and modify the IP address of the camera over the LAN.

Before You Start

• Get the SADP software from the official website, and install the SADP according to the prompts.
  (https://www.hikvision.com/en/support/tools/hitools/clea8b3e4ea7da90a9/)

• The camera and the PC that runs the SADP tool should be within the same subnet.

1. Power over Ethernet by S ngle Ethernet Cord
   When Works w ith PoE NVR or PoE Switch

2. Power on by Additional Power Adapter
   When Works Standalone (Power Adapter is Not Included)

The following steps show how to activate one device and modify its IP address

Steps:

1. Run the SADP software and search the online devices.

2. Find and select your device in on line device list.

3. Input new password (admin password) and confirm the password.
   Cautions
   STRONG PASSWORD RECOMMENDED-We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.

4. Click Activate to start activation

5. Enable “Guarding Vision” Service.
   Steps:

6. Check “Hik-Connect” to enable “Guarding Vision” APP/PC Client remote access.

7. Create “Verification Code”, it’s required when you add device to “Guarding Vision” (APP and PC Client)

8. Status of the device becomes Active after successful activation.

9. Modify IP address of the camera.

10. Select the device.

11. Check Enable DHCP , or change the device IP address to the same subnet as your computer by modifying the IP address manually

12. Input the ad min password and click Modify to activate your IP address modification.

Access Camera

This part introduces how to access the camera via Web browser.

1. Access Camera via Web Browser
   Before You Start
   Check the system requirement to confirm that the operating computer and web browser meets the requirements.

Operating System| Microsoft Windows XP and above version, Mac OS X 10.8 and above version
---|---
CPU| 3.0 GHz or higher
RAM| 1 GB or higher
Display| 1024 x 768 resolution or higher
Web Browser| Internet Explorer 8.0 and above version, Mozilla

Firefox 30.0- 51, Google Chrome 31.0-44, Safari 8.0+

Steps:

1. Open the web browser.

2. Input IP address of the camera to enter the login interface.
   (You can find the camera’s IP address by SADP tool, refer to page 4)

3. Input user name and password.
   NOTE:
   Illegal login lock is activated by default. If admin user performs seven failed password attempts (five attempts for user/operator), the IP address is blocked for 30 minutes.
   If illegal login lock is not needed, go to Configuration ➔ System ➔ Security ➔ Security Service to turn it off.

4. Click Login.

5. Live View

6. (DMain Stream (High Definition)

7. Sub Stream (Standard Definition)

Configuration via Web Browser
All the settings that the camera offers can be adjusted by accessing it via a web browser using the IP address.

Enable ONVIF
If you want add the camera to third-party NVR, please check “Enable Open Network Video Interface” (ONVIF), and create ONVIF user name and password

Reset Camera via Web Browser
Navigate to Configuration➔ System➔Maintenance➔ Restore/ Default
Restore: Reset all the parameters, except the IP parameters and user information, to the default settings.
Default: Restore all parameters to default settings.

Operate via Mobile Client

Guarding Vision is an application for mobile devices. Using the App, you can view live image, receive alarm notification and so on.

1. Enable Guarding Vision Service on Camera
   Guarding Vision service should be enabled on your camera before using the service. You can enable the service through SADP software or Web browser.

2. Enable Guarding Vision Service via SADP Software
   This part introduces how to enable Guarding Vision service via SADP software of an activated camera.
   Steps:

3. Run SADP software.

4. Select a camera and enter Modify Network Parameters page.

5. Check Enable “Hik-Connect”.

6. Create a verification code or change the old verification code. & NOTE:
   The verification code is required when you add the camera to Guarding Vision service.

7. Click and read “Terms of Service” and “Privacy Policy”.

8. Confirm the settings.

Enable Guarding Vision Service via Web Browser
Follow the following steps to enable Guarding Vision Service via Web Browser.

Before You Start:
You need to activate the camera before enabling the service.

Steps:

1. Access the camera via web browser.

2. Enter platform access configuration interface. Configuration ➔ Network ➔ Advanced Settings ➔ Platform Access.

3. Select Guarding Vision as the Platform Access Mode.

4. Check Enable.

5. Click and read “Terms of Service” and “Privacy Policy” in pop-up window.

6. Create a verification code for the camera.
   NOTE: The verification code is required when you add the camera to Guarding Vision service.

7. Save the settings.
   The “Register Status” should become “Online” after enabled “Guarding Vision”.

Add Camera to Guarding Vision (APP)
Before you start:

1. Download and install the Guarding Vision app by searching
   “Guarding Vision” in App Store or Google Play.

2. Launch the app and register for a Guarding Vision user account.

3. Connect your mobile device to a Wi-Fi. {Should be within the same subnet with the camera)

Steps:

1. Log into the Guarding Vision app.

2. In the home page, tap”+” on the upper-right corner, select “Online Device”
   The device under same network will be detected, select the device and tap on “Add Device to Guarding Vision Service”
   If you tap on “Add”, will be only able to remote access it within same WLAN.

3. Input verification code, not password. (Refer to page 5), add camera according to the prompts.

4. You also can add the camera by scanning the QR code on camera body.
   (If the QR code is missing or too blur to be recognized, you can add the camera by inputting the camera’s serial number.)

Operate via PC Client

Before You Start:

• Get the Guarding Vision software from manufacturer, (Please email us at Love@Hiseeu.com) and install the Guarding Vision according to the prompts.
  Steps:

  1. Run the Guarding Vision software
  2. Create a super user name and password.
  3. Setup security questions
  4. Login after registration
  5. Login in with Your APP Account
  6. Navigate to “Main View”, the device you added on the APP will sync automatically
  7. Stream Key is the “Verification Code” , not password. Input the code you created when you enable “Hik-Connect” (Refer to Page 5)

Add Camera to NVR

Add camera to Hiseeu 4K PoE NVR Steps:

1. Connect the camera to Hiseeu 4K PoE NVR PoE port via network cable
2. Ensure camera is powered on properly
3. Reset the camera by pressing the camera reset button. (Refer to page 1)
4. Navigate to MenuCameralP Channel
5. NVR will activate the camera and auto connect it After configuration, the camera’s User Name is admin, Password: same as NVR.

Add camera to third-party NVR
Before You Start:

1. Ensure the NVR is ONVIF compatible and support 4K video input.
2. Ensure camera is activated via SADP tool (refer to page 4)
3. Ensure camera ONVI F is enabled (refer to page 11)

Steps:

1. Modify the camera’s IP, make it as same as NVR’s subnet if the NVR’s address is 192.168.2.1, then the camera should be in the same format (for example 192.168.2.100). Or if the NVR’s address is 10.0.0.1, then the camera can be set on 10.0.0.100. To the camera’s IP address has to match NVR’s network.
2. Input correct user name and password during configuration
   Any questions, please feel free to contact us at Love@Hiseeu.com (917 618 2228)

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>