dji RM4739 RS3 Pro Combo Gimbal Stabilizer User Guide
- June 4, 2024
- DJi
Table of Contents
dji RM4739 RS3 Pro Combo Gimbal Stabilizer
Safety at a Glance
Please read this entire document and visit https://www.dji.com/rs-3-pro to view the user manual, other documents, and the tutorial videos with the most current instructions and warnings. Failure to read and follow instructions and warnings may result in personal injury, damage to your DJI OSMOTM product, or other objects in the vicinity. This document and all other collateral documents are subject to change at the sole discretion of DJI OSMO. By using this product, you hereby signify that you have read and agreed to abide by the terms and conditions of this document. You agree that you are solely responsible for your own conduct while using this product and for any consequences thereof. This product is not intended for use by children without direct adult supervision.
CAUTION
- DJITM RS 3 Pro is powered by a built-in battery through the grip. Users take full responsibility for all operations and usage.
- DO NOT use non-DJI batteries. Go to www.dji.com to purchase new batteries. DJI takes no responsibility for any damage caused by non-DJI batteries.
- The grip should be used in temperatures from -20° to 45° C (-4° to 113° F). Use of the grip in environments above 50° C (122° F) can lead to a fire or explosion. Use of the grip in environments where the temperature is below -10° C (14° F) can significantly reduce operation time.
- DO NOT disassemble or pierce the grip in any way or the battery may leak, ignite, or explode.
- DO NOT drop or strike batteries. DO NOT place heavy objects on the grip or charger.
- DO NOT heat batteries. DO NOT put the grip in a microwave oven or in a pressurized container.
- Contact DJI Support immediately if any of the components break in order to avoid further damage and risk of injury.
- DJI RS 3 Pro has built-in high precision sensors. Dropping or striking it in any way may cause permanent sensor damage, leading to abnormal functionality. Contact DJI Support immediately if this
happens.
CAUTION
- DO NOT disassemble DJI RS 3 Pro or its accessories. Improper or poor handling could damage the gimbal.
- Make sure to keep DJI RS 3 Pro clear of dust and water. Otherwise, it may be damaged.
- Make sure to mount the gimbal firmly when using DJI RS 3 Pro in a high-speed situation.
- If DJI RS 3 Pro is mounted to a car, a safety rope is required to tightly secure the gimbal. Only drive on paved roads at a speed less than 100 km/h while shooting.
NOTICE
- The motor may become hot after long operating durations with the gimbal unbalanced, and operation time will be reduced significantly.
- DO NOT obstruct the gimbal movements. Otherwise, you may injure your hand.
Specifications
- Model P03P
- USB Input 5V/2A, 9V/2A, 12V/2A, 15V/1.6A
- Bluetooth Operating Frequency 2.4000 GHz-2.4835 GHz
- Bluetooth Transmitter Power <8 dBm
- Operating Temperature -20° to 45° C (-4° to 113° F)
Compliance Information
FCC Compliance Notice
We, DJI Technology, Inc., being the responsible party, declares that the
above mentioned model was tested to demonstrate complying with all applicable
FCC rules and regulations. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must acceptany interference
received, including interference that may cause undesired operation. Any
changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if notinstalled and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
ISED Compliance Notice
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions: (1) This device
may not cause interference. (2)This device must accept any interference,
including interference that may cause undesired operation of the device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>