HF Protoss-PE11 RS485 to Ethernet User Manual

June 4, 2024
HF

HF Protoss-PE11 RS485 to Ethernet

HF Protoss-PE11 RS485 to Ethernet

Overview of Characteristic

  • Cortex-M3 MCU with 2MB Flash and 128KB SRAM
  • Use FreeRTOS Operation System
  • Support TCP/UDP/MQTT/HTTP/WebSocket Protocol
  • Support Modbus TCP to RTU, Modbus Master Function
  • Support RS485 To 10/100M Ethernet Conversion, Serial Speed Up to 460800 bps
  • Support 10/100M Ethernet Auto-Negotiation
  • Support Webpage Easy Configuration or PC IOTService Tool
  • Support Security Protocol Such As AES/DES3
  • Support Heartbeat and Resister Packet Function
  • Support Webpage OTA Wireless Upgrade
  • Support Industrial Temperature: -40 to +85˚ C
  • Multiple Type of Different Power Input:
    • Protoss-PE11-H:100~240VAC@50~60Hz
    • Protoss-PE11-M:9~48VDC@1A
  • Size: 97.60 x 64.95 x 27.50 mm (L x W x H) ,C45 rail installation

PRODUCT OVERVIEW

General Description
The Protoss-PE11 provides a RS485 interface to TCP/IP data transfer product. The Protoss-PE11 integrate TCP/IP controller, memory, 10/100M Ethernet transceiver, RS485 and integrates a fully developed TCP/IP network stack and FreeRTOS OS. Protoss-PE11 also includes an embedded web server used to configure device.
The Protoss-PE11 using highly integrated hardware and software platform, it has been optimized for all kinds of applications in the industrial control, smart grid, personal medical application and remote control that have lower data rates, and transmit or receive data on an infrequent basis.

Device Paremeters

Table1. Protoss-PE11 Technical Specifications

Item Parameters

System Information
Processor/Frequency| Cortex-M3/96MHz
Flash/SDRAM| 2MB/128KB
Operating System| FreeRTOS
Ethernet Port
Port Number| 1
Interface Standard| 10/100 Base-T Auto-Negotiation
Transformer| Integrated
Network Protocol| IP,TCP,UDP,DHCP,DNS,HTTP Server/Client,ARP, AutoIP, ICMP, Telnet, NTP, Modbus TCP
Security Protocol| AES 128Bit DES3
Serial Port
Port Number| 1 RS485
Data Bits| 5,6,7,8
Stop Bit| 1,2
Check Bit| None, Even, Odd
Baud Rate| TTL: 600 bps~460800 bps
Flow Control| No Flow Control

Software Xon/ Xoff flow control

Software
Web Pages| Http Web Configuration Customization of HTTP Web Pages

Configuration

| Web CLI

XML import

| Telnet

IOTService PC Software UART Fast Config

---|---
Firmware Upgrade| Webpage, IOTService Tools
Basic Parameter
Size| 97.60mm x 64.95mm x 27.50mm
Operating Temp.| -40 ~ 85°C
Storage Temp.| -45 ~ 105°C, 5 ~ 95% RH(no condensation)
Input Voltage| Protoss-PE11-H:100~240VAC@50~60Hz

Protoss-PE11-M:9~48VDC@1A

Working Current| ~100mA
Power| <400mW

Key Application

The Protoss-PE11 device connects serial device to Ethernet networks using the TCP/IP protocol:

  • Remote equipment monitoring
  • Asset tracking and telemetry
  • Security Application
  • Industrial sensors and controls
  • Medical devices
  • ATM machines
  • Data collection devices
  • Universal Power Supply (UPS) management units
  • Telecommunications equipment
  • Data display devices
  • Handheld instruments
  • Modems
  • Time/attendance clocks and terminals

HARDWARE INTRODUCTION

The Protoss-PE11 unit is a complete solution for serial port device connecting to network. This powerful device supports a 10/100BASE-T Ethernet connection, a reliable and proven operating system stored in flash memory, an embedded web server, a full TCP/IP protocol stack, and standards-based (AES) encryption.
Through Ethernet cable connect router with Protoss-PE11 serial server for data transfer, which makes the data transformation very simple.

HF Protoss-PE11 RS485 to Ethernet-1

Protoss-PE11 Pins Definition

Table2. Protoss-PE11-H Interface Definition

Pin Description Net Name Signal Type Comment
1 AC Power Input L Power 100~240VAC Input
2 AC Power Input N Power
5 RS485_B- IO RS485 B-
6 Signal GND GND Power Used for RS485 GND, usually leave it unconnected
7 RS485_A+ IO RS485 A+
RJ45 Ethernet RJ45 I/O
Reload Restore to factory setting button Reload I Press down for more than

3 seconds and loose to restore factory setting.
Reset| Reset button| Reset| I| Hardware reset button
Net| Network status LED| Net| O| On: Ethernet connection is OK Off: No Ethernet connection

Active

|

UART Data Transfer

|

Active

|

O

| Off: No data transfer

0.3s Off -> 0.9s On: UART TX Output 0.3s Off -> 0.3s On: UART RX Receive On: UART bidirection.

Power| Power LED| Power| O| On: Power input OK Off: Power input NG.
Link| Server connection LED| Link| O| On: netp Socket connection OK. Off: no netp Socket connection.

Table3. Protoss-PE11-M Interface Definition

Pin Description Net Name Signal Type Comment
1 DC Power Input VCC+ Power 9~48VDC@1A Input
2 DC Power Input GND- Power
5 RS485_B- IO RS485 B-
6 Signal GND GND Power Used for RS485 GND, usually leave it unconnected
7 RS485_A+ IO RS485 A+
RJ45 Ethernet RJ45 I/O
Reload Restore to factory setting button Reload I Press down for more than

3 seconds and loose to restore factory setting.
Reset| Reset button| Reset| I| Hardware reset button
Net| Network status LED| Net| O| On: Ethernet connection is OK Off: No Ethernet connection

Active

|

UART Data Transfer

|

Active

|

O

| Off: No data transfer

0.3s Off -> 0.9s On: UART TX Output 0.3s Off -> 0.3s On: UART RX Receive On: UART bidirection.

Power| Power LED| Power| O| On: Power input OK Off: Power input NG.
Link| Server connection LED| Link| O| On: netp Socket connection OK. Off: no netp Socket connection.

I — Input; O — Output; I/O: Digital I/O; Power—Power Supply

RS485 Interface
RS485 use two wire links, A(DATA+), B(DATA-). Connect A(+) to A(+), B(-) to B(-) for communication. Suggest to connect GND together when interference is very severe.
The RS485 interface support maximum 32 RS485 device. The cable maximum length is 1200 meters. Need to add 120Ohm terminal resistor for over 300 meters.

RJ45 Interface
Ethernet port is 10M/100M adaptive, support AUTO MDI/MDIX which means it support direct connecting to PC with Ethernet cable.

Table4. RJ45 Interface

Pin Number Name Description
1 TX+ Transfer Data+
2 TX- Transfer Data-
3 RX+ Receive Data+
4 PHY-VCC Transformer Tap Voltage
5 PHY-VCC Transformer Tap Voltage
6 RX- Receive Data-
7 N.C. None Connect
8 N.C. None Connect

Mechanical Size

The dimensions of Protoss-PE11 are defined as following picture (mm):

HF Protoss-PE11 RS485 to Ethernet-6

HF Protoss-PE11 RS485 to Ethernet-7

Product Installation

HF Protoss-PE11 RS485 to Ethernet-8

Order Information
Base on customer detailed requirement, Protoss-PE11 provide different configuration version, Details as below:

FUNCTION DESCRIPTION

Refer to “IOT_Device_Series_Software_Funtion” document for more detailed function.

APPENDIX A: CONTACT INFORMATION
————————————————————————————————————
Address: Room 1002,Building 1,No.3000,Longdong Avenue,Pudong New Area,Shanghai,China,201203
Web: www.iotworkshop.com or www.hi- flying.com
Contact:
Sales: sales@iotworkshop.com
Support: support@iotworkshop.com
Service: service@iotworkshop.com
Business: business@iotworkshop.com —————————————————————————- ——————————-
For more information about IOTworkshop modules, applications, and solutions, please visit our web site www.iotworkshop.com

http://www.hi-flying.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals