Samsara CBL-AG-BRTK Asset Gateway For Trailers Installation Guide
- June 7, 2024
- Samsara
Table of Contents
Samsara CBL-AG-BRTK Asset Gateway For Trailers Installation Guide
Asset Gateway
CBL-AG-BRTK
CABLE DIAGRAM
WHAT YOU’LL NEED
(STANDARD LOCATION INSTALLATION)
WHAT YOU’LL NEED (HAZARDOUS LOCATION INSTALLATION)
HELPFUL LINKS
Install AG52/53 on Powered Equipment
Install Tips
In order to complete this installation, please ensure you have both the Samsara hardware and Thermo King hardware parts needed. Depending on your reefer model and year, you will need either an REB iBox or a BlueBox with the respective 3rd party compatible harnesses from Thermo King. Models 2018 and newer will have a Blue Box pre-installed in the reefer. Please confirm you have the 3rd party compatible harness. For models prior to 201 8, you may have an REB iBox with a harness that can be used. If not, please consult with your Thermo King dealer to procure the necessary Thermo King hardware. For any questions regarding which Thermo King parts are needed please refer to the Model Compatibility Guide or your local Thermo King dealer.
Reminder for models with a BlueBox, you will need to contact Thermo King support at tracking support@ thermoking.com, or work with your local Thermo King dealer with your Blue Box serial number and IMEI to request that your BlueBox be remotely reconfigured to iBox mode. This will enable Samsara to communicate with your reefer unit.
standard location installation
When selecting a location for your device, reference the following tips:
Verify that the cable has adequate clearance to reach the AG and the electrical connection. Ensure that the AG has a clear view of the sky. Avoid installing the device within metallic structures, such as within metal trailers.
Placement in such structures may adversely impact device cellular and GPS connectivity.
Attach the gateway to the asset using the provided #6 self-drilling screws with maximum torque of 1.4 Nm (12.4 lbf-in). If you choose to fasten the device with your own screws, use these recommendations for screw size to avoid damage to the device mounting tabs.
If you are installing at a hazardous location, use the following
recommendations:
Attach the mounting plate with included self-drilling screws to the mounting
surface. With cable plugged in,assemble the Asset Gateway and cover. Fasten
with the two included machine screws. Wire the included 2A fuses between cable
and power source(s).
WARNING — EXPLOSION HAZARD. DO NOT CONNECT OR DISCONNECT WHEN ENERGIZED. DO NOT DISCONNECT WHILE THE CIRCUIT IS LIVE OR UNLESS THE AREA IS FREE OF IGNITIBLE CONCENTRATIONS.
IMPORTANT SAFETY AND USE INFORMATION
This installation guide contains typical information specific to products manufactured at the time of its publication. The contents of this guide do not constitute a warranty and are for reference only. Consult applicable local laws and ordinances to determine any installation restrictions. It is the installer’s responsibility to comply with all applicable laws and ordinances when installing this hardware.
Do not attempt to repair this product, use any third party replacement parts with this product, or otherwise modify this product except in accordance with product manuals or as otherwise instructed by Samsara. Failure to do so may cause property damage, lead to physical injury, or void your product warranty.
Any installation not in accordance with the instructions in the installation guide or otherwise in the Documentation or other than as described by the relevant IP rating or recommended operating conditions may result in physical injury or property damage. Failure to follow these directions could result in serious injury or death.
This hardware and any associated software may not be compatible with third party products and/or services and may interfere with the operations of or void warranties for such third party products and/or services.
Do not install or adjust hardware while driving or operating the vehicle. Do not install this hardware in a location that could interfere with the driver’s visibility or operation of vehicle controls. Do not install this hardware on or near airbag panels or within the working range of an airbag.
Do not install hardware while the vehicle is unsecured. Do not install hardware while the vehicle is turned on unless instructed to turn on the vehicle by the installation guide. Failure to follow installation instructions may cause serious physical injury, damage to the vehicle or the hardware, and void vehicle or other third party product warranties.
Batteries in the hardware may have a shorter life span if not used in accordance with instructions. Do not short circuit, crush, disassemble, heat above 60°C/140°F, incinerate, or expose the battery or its contents to water. Do not remove the battery from the hardware to recharge or for any other reason, including disposal. Do not solder directly to the battery cell. Do not use if battery appears damaged.
This product includes capacitors and batteries which may present a potential fire, explosion, electric shock, or burn hazard. Do not touch or come into close proximity to any capacitors within this hardware.
Keep this hardware between -400C/-400F to 600C/1400F externally powered, -200C/-40F to 600C/1400F discharging on battery, OOC/320F to 450C/1130F charging. Failure to keep this hardware in the specified temperature range may result in safety risks.
Failure to follow mounting instructions may create risk of physical injury or property damage from falling objects. If mounting the hardware to a building wall, check for wiring or plumbing before drilling any holes.
After installation, this product will be able to charge batteries at any moment.
© 2024 Samsara Inc.
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>