HIKVISION DS-2SF8C442MXS-DLW TandemVu PTZ Camera User Guide
- June 4, 2024
- Hikvision
Table of Contents
TandemVu PTZ Camera
Quick Start Guide
http://enpinfodata.hikvision.com/analysisQR/showQR/5b0cdcf2
DS-2SF8C442MXS-DLW TandemVu PTZ Camera
| 
---|---
| 
| 
| 
| 
| 
http://enpinfodata.hikvision.com/analysisQR/showQR/902c0519\nQR-
Code:
http://enpinfodata.hikvision.com/analysisQR/showQR/d983b5d2
** Read this manual before using the product.
Product appearance is for reference only and may differ from the actual
product.
Symbols and Marks (Page 2 – A)**
- Notice
- Warning
- Forbidden
- Correct
- Incorrect
- Turn to step A and continue.
- Not necessarily included accessory. /Variable accessory amount. /Skip this step if not required.
- MicroSD card
- Grounding
- Disposal
- Purchase separately
- Possible options
Accessory and Interface (Page 4- C
Accessory and Interface (Page 4- C)
① Memory card slot
② Reset button: Press the reset button for about 10 s when the camera is
powering on or rebooting to restore the default settings, including the user
name, password, IP address, port No., etc.
③ Network interface
④ RS-485 interface
⑤ Power interface
⑥ Audio interface/Alarm interface
⑦ Optical fiber interface
Install Camera (Page 5 – D)
Alarm Output (Page 11 – E)
① Relay output
② DC load
③ Power supply
④ JQC-3FG Relay
Protective Measures for Outdoor Installation (Page 11 – F1)
Activate and Access Network Camera (Page 11 – F2)
© 2021 Hangzhou Hikvision Digital Technology Co., Ltd. All rights
reserved.
About this Manual
The Manual includes instructions for using and managing the Product. Pictures,
charts, images and all other information hereinafter are for description and
explanation only. The information contained in the Manual is subject to
change, without notice, due to firmware updates or other reasons. Please find
the latest version of this Manual at the Hikvision website
(https://www.hikvision.com/).
Please use this Manual with the guidance and assistance of professionals
trained in supporting the Product.
Trademarks
and other Hikvision’s trademarks and logos are the properties of Hikvision in
various jurisdictions. Other trademarks and logos mentioned are the properties
of their respective owners.
DISCLAIMER
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT
DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED “AS IS” AND
“WITH ALL FAULTS AND ERRORS”. HIKVISION MAKES NO WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING WITHOUTLIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY,
OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR
OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS,
DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA,
CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF
CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN
CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES OR LOSS.
YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY
RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL
OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK,
HACKER ATTACK, VIRUS INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER,
HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU
ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE
LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT
DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT
LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA
PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY
PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF
MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL
WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR
UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE
LATTER PREVAILS.
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment. FCC compliance: This equipment has been tested and
found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
EU Conformity Statement
This product and – if applicable – the supplied accessories too are marked
with “CE” and comply therefore with the applicable harmonized European
standards listed under the EMC Directive 2014/30/EU, the RoHS Directive
2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points.
For more information see: www.recyclethis.info
2006/66/EC and its amendment 2013/56/EU (battery directive): This product
contains a battery that cannot be disposed of as unsorted municipal waste in
the European Union. See the product documentation for specific battery
information. The battery is marked with this symbol, which may include
lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg).
For proper recycling, return the battery to your supplier or to a designated
collection point. For more information see:
www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
Warning
This is a class A product. In a domestic environment this product may cause
radio inter-ference in which case the user may be required to take adequate
measures.
Safety Instructions
Warnings
Laws and Regulations
The device should be used in compliance with local laws, electrical safety
regulations, and fire prevention regulations.
Electrical Safety
CAUTION: To reduce the risk of fire, replace only with the same type and
rating of fuse.
This equipment shall be installed incorporated with UPS to avoid the risk of
restart.
Battery
This equipment is not suitable for use in locations where children are likely
to be present.
CAUTION: Risk of explosion if the battery is replaced by an incorrect
type.
Improper replacement of the battery with an incorrect type may defeat a
safeguard (for example, in the case of some lithium battery types).
Do not dispose of the battery into fire or a hot oven, or mechanically crush
or cut the battery, which may result in an explosion.
Do not leave the battery in an extremely high temperature surrounding
environment, which may result in an explosion or the leakage of flammable
liquid or gas.
Do not subject the battery to extremely low air pressure, which may result in
an explosion or the leakage of flammable liquid or gas.
Dispose of used batteries according to the instructions.
Cautions
Fire Prevention
No naked flame sources, such as lighted candles, should be placed on the
equipment.
The serial port of the equipment is used for debugging only.
Hot Surface
CAUTION: Hot parts! Burned fingers when handling the parts.
WARNING HOT SURFACE DO NOT TOUCH
This sticker is to indicate that the marked item can be hot and should not
be touched without taking care. Wait one-half hour after switching off before
handling parts. The device with this sticker is intended for installation in
a restricted access location. Access can only be gained by service persons or
by users who have been instructed about the reasons for the restrictions
applied to the location and about any precautions that shall be taken.
Installation
Install the equipment according to the instructions in this manual.
Be sure that there is enough space to install the device and accessories.
Make sure that the wall is strong enough to withstand at least 8 times the
weight of the camera and the mount.
Make sure that the power has been disconnected before you wire, install, or
disassemble the device.
Transportation
Keep the device in original or similar packaging while transporting it.
Do not drop the product or subject it to physical shock.
Power Supply
The power source should meet limited power source or PS2 requirements
according to IEC 60950-1 or IEC 62368-1 standard.
Refer to the device label for the standard power supply. Please make sure your
power supply matches with your device. Use a power adapter provided by
qualified manufacturers. It is recommended to provide an independent power
adapter for each device as adapter overload may cause over-heating or a fire
hazard.
System Security
Please understand that you have the responsibility to configure all the
passwords and other security settings about the device, and keep your user
name and password.
Maintenance
If the product does not work properly, please contact your dealer or the
nearest service center. We shall not assume any responsibility for problems
caused by unauthorized repair or maintenance.
A few device components (e.g., electrolytic capacitor) require regular
replacement. The average lifespan varies, so periodic checking is recommended.
Contact your dealer for details.
Cleaning
Please use a soft and dry cloth to clean the interior and exterior surfaces.
Do not use alkaline detergents.
Using Environment
When any laser equipment is in use, make sure that the device lens is not
exposed to the laser beam, or it may burn out. Do not aim the lens at the sun
or any other bright light.
To avoid heat accumulation, good ventilation is required for a proper
operating environment.
DO NOT expose the device to extremely hot, cold, dusty, corrosive, saline-
alkali, or damp environments. For temperature and humidity requirements, see
device specification.
DO NOT expose the device to high electromagnetic radiation.
Illuminator
Make sure that there is no reflective surface too close to the camera lens.
The IR light from the camera may reflect back into the lens causing
reflection.
The beam of the light at the distance of 200 mm is classified as Risk Group 1
(RG1). Possible hazardous optical radiation emitted from this product. Do NOT
stare at operating light source. May be harmful to the eyes.
If appropriate shielding or eye protection is not available, turn on the light
only at a safe distance or in the area that is not directly exposed to the
light when installing or maintaining the device.
Emergency
If smoke, odor, or noise arises from the device, immediately turn off the
power, unplug the power cable, and contact the service center.
Time Synchronization
Set up device time manually for the first time access if the local time is not
synchronized with that of the network. Visit the device via Web browse/client
software and go to time settings interface
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>