TOPVISION T23 Doorbell Camera User Manual

June 4, 2024
TOPVISION

T23 Doorbell Camera
User Manual 2.0

Features

| |
---|---|---

  1. Microphone
  2. Wide-angle Lens
  3. LED indicator
  4. Hidden Infrared Lights
  5. Light Sensor
  6. Doorbell Button
  7. Reset Button
  8. Speaker
  9. USB Port (Battery Charging)
  10. Security screw hole

Indicator Light

| Flashing RED
The device is disconnected from WiFi. It will reconnect automati-cally. But if it failed, please reset the device and pair it again in App.
---|---
| Flashing RED and BLUE alternately
| Low battery.
Please recharge the device.
| Flashing BLUE
The device is capturing images.

In the box

Doorbell Tape Chime (Optional)
USB Cable (Optional) 3 Screws 2 Anchors

Charge the Doorbell

Fully charge the doorbell with a 5V1 A USB charger and a Type-C cable. It takes about 2-3 hours to fully charge.

WARNING: Lots of events
If you have an excessive number of visitors, you might need to charge it sooner.

Set up your Doorbell
Before You Start

  1. Download and install Aiwit App. Scan the QR code below or search for Aiwit on the App Store or Google Play. Download and install the app.
    Aiwit| https://www.aiwit.cc/download
    Android/iOS App Download
    ---|---

Set up your device in the Aiwit app.
To pair your device, follow the steps below and in-app instructions.

  1. Open Aiwit App and log in to your account.
  2. Tap the “+” icon to add a new device.
  3. Select Mini Doorbell, then choose your doorbell model.
  4. Press and hold the Doorbell Button until the red light is flashing, tap Next, then tap Yes.
  5. Enter your 2.4GHz Wi-Fi network and the Wi-Fi password, then tap Next (5GHz is not supported).
  6. Use your device camera to scan the QR Code

4 Inches (10 cm)

Install your Doorbell

Mark drill holes and use a bit to drill holes in your wall. Insert anchors and secure your doorbell with mounting and security screws.

Step 1 Step 2

Frequently asked questions

  • You can always ask questions in Customer Service in Aiwit App. The service is free.
    How to RESET the doorbell
    To reset, please delete your current device, press and hold the Doorbell Button for around 8 seconds till it flashes red. Then click the “+” icon in- app, to add the device again.

How to share the device with my family
Open Aiwit App. Tap the Settings ( icon, then tap the Share ( ) icon to get to Sharing Device page. On Sharing Device page, you can share the device via email or QR code scanning, and you can also transfer the device.
The new user has to download Aiwit App and create his/her own account first.
Share via QR Code:

  • Tap the Share via QR Code icon ( ), it will show a QR code on your phone.
  • Open the Aiwit on the new user’s phone, tap the “+” icon, then tap the Scan icon at the top right corner, and scan the QR code.
  • You will see Share Successfully. And the new user will see the shared device in his/her own account. Share via email:
  • Tap the Share via Email icon ( ), then enter the new user’s email address.
  • Tap confirm. You will see Share Successfully. And the new user will see the shared device in his/her own account.

Transfer device:

  • Tap the Transfer icon( ), then enter the new user’s email address. Or, if you want to transfer the device to your shared accounts, just choose the shared account.
  • Tap confirm. Then transfer successfully.

Notes: Only the owner account can change settings, delete videos, and share devices. Shared accounts don’t have these options.

How many users can view the doorbell at the same time?
The owner account can share with 8 other accounts. Up to 3 users may view the video feed at one time, but only 1 user can use the intercom.

Is the 5GHz Wi-Fi supported?
No, it only works with 2.4GHz Wi-Fi.

Why is my Wi-Fi signal poor?
Your device may be too far away from your wireless router or you may have some obstructions in between that reduce signal strength. You might try repositioning your router or getting a signal extender/repeater for your wireless router.

Why is my device offline?
Offline means the device is disconnected. There are usually two possible reasons:

  1. The device has run out of power. Please try to push the doorbell button, and see if there is a light on the doorbell. If not, please charge the doorbell.
  2. Wi-Fi was weak and the device disconnected from Wi-Fi. Please reconnect to Wi-Fi. The device works with 2.4G Wi-Fi only, please make sure your Wi-Fi is stable, and consider repositioning your router to make stronger Wi-Fi for the device. It is very important that the device gets good Wi-Fi because it is outside of the house.

How to enable Notifications on my phone
There are notification settings inside Aiwit App, and in mobile settings:

  1. Open Aiwit App. From the Device page, tap the Settings icon, and you will see “Ring Alert”. You can choose to turn on/off ring alerts.
  2. Open mobile settings, find App Management and/or Notification Settings, then find Aiwit App. Make sure all authorizations and notifications are turned on for Aiwit App.

Set up your Wireless Chime (Optional)

Connect the doorbell to the doorbell chime, and get an instant alert in your home when someone rings the doorbell. The chime plugs into any 5V USB port, you can place it anywhere in the home.
NOTICE: The doorbell is only compatible with our wireless chime, and not compatible with traditional doorbell chimes. The wireless chime is optional. If it is not installed, doorbell notifications will still go directly to the Aiwit
The Basics

Step 1
Before the setup process, be sure your doorbell has connected to your phone. Then plug your chime into the USB port.

Step 2
Press the pair button.

Step 3
Press the Doorbell Button for pairing.

Step 4
Press the Doorbell Button again to verify the chime and doorbell work properly.

* Volume of the chime is not adjustable

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals