Beser A30 Wireless Car Charger User Guide

Beser A30 Wireless Car Charger

Product Specifications

• Input: 5V 3A, 9V 2.22A
• Output: Maximum of 15W

Charging the Device

To charge your device using this charger, follow these steps:

1. Plug the charger into a power outlet.
2. Connect your device to the charger using a compatible charging cable.
3. Ensure the device is securely connected to the charger.
4. The charger will start charging your device automatically.

Disposal Instructions

When disposing of this product, remember the following:

1. Do not treat this product as household waste.
2. Hand it over to the applicable collection point for recycling of electrical and electronic equipment.

FAQ:
Q: Who is the manufacturer of this product?
A: The manufacturer of this product is Rongyichuang (Shenzhen) Technology Co., Ltd.

How to, charge Properly?

So laden Sie richtig auf? Comment Recharger Correctement?

Fast charging schnellladen Charge rapide
Unable to charge or slow to charge Laden kann nicht oder langsam geladen werden Impossible de charger ou lent à charger

1. inside case
   on case

2. General case
   Bare nhone

3. Align the circle of the match-up card to the center of the phone

4. wait for 24 hour

The best experience is the Magsafe phone case

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2.  this device must accept any interference received, including interference that may cause undesired operation.

Warning
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCCRules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.

This product complies with the radio interference requirements of the European Community.

EN Declaration of Conformity
This product is intended for use within Europe. Electronic Silk Road Corp. hereby declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU,2014/35/EU,2014/30/EU

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TVtechnician for help.

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance20cm between the radiator &your body.

www.beservip.com – beservip@outlook.com

Indicator Light Guide

If an error is detected:

1. Check that your phone supports wireless charging and does not have any credit cards, stands, or other metal attachments on the back (other than the magnetic ring).
2. After checking the above, unplug and plug in the charging cable again to resume normal charging.

Important Reminders

1. Compatible with MagSafe-enabled iPhones and cases.
2. This charger supports an input of 5V 3A, 9V 2.22A and outputs a maximum of 15W.
3. Only use the cable provided with the charger. An Apple cable or other third-party cable may interfere with charging.
4. This charger requires a charging adapter that supports QC or PD fast charging and an output of at least 18W.
5.  Charger must be plugged in to power supply to charge devices.

Safety Warnings

1. Do not place the device in temperatures below 0°C (32°F) or above 60°C (140°F).
2. Do not attempt to disassemble the device, expose it to an open flame, or submerge it in water to avoid damaging the device.
3. Always check for damage to the device, cables, or other accessories before using the device. If damaged, do not use the device.
4. Do not attempt to disassemble or modify the device in any way, as it may cause serious damage and void the warranty.
5. Do not expose the device to extremely hot, humid, or corrosive environments to avoid damaging the device.

This symbol indicates that this product shall not be treated as household waste.Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.

• Manufacture： Rongyichuang (Shenzhen) Technology Co., Ltd
• Add：longgangqu bantianjiedao wankechengshequ
• xintianxia bairuidadasha A zuo 7F755 shenzhen guangdong
• Tel：+8613243899821
• Email: ongyichuang@outlook.com

CET PRODUCT SERVICE
SP. Z 0.0. Ul. Dluga 33 102 Zgierz 95-100 Polen
Tel: +4971416432236 Email: info@cetproduct.com CET Product Service Ltd. Beacon House

Stokenchurch Business Park, Ibstone Rd,
Stokenchurch High Wycombe HP14 3FE UK Tel: +44741932526 Email: info@cetproduct.com

www.beservip.com beservip@outlook.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>