Elite EFM-1307R Water Mist Fan User Manual

EFM-1307R Water Mist Fan
User Manual

Note: The specifications and/or components of this appliance are subject to change without prior notice.
SPRAYING MIST FAN

USEFUL INFORMATION:

Please read this user manual thoroughly before operating it to correct and efficient use of the fan, and keep it for any future reference.
Please turn off the power and unplug it when it isn’t working, this can save power consumption and extend the lifespan of the appliance.

SPECIFICATIONS

CAUTIONS

Before using, please check if the power supply is following the voltage label on the bottom of the appliance.| | Please switch off the power before unplugging
Don’t pull the plug with a wet hand to avoid getting an electric shock.|
---|---|---|---
Before using, please check if the wire and the plug are damaged. Don’t fold and pull the wire.| | Don’t put fingers or sharp things into the fan guard when it is working.|
Don’t use the fan in such places where the curtain may be drawn in.| | Don’t use before complete assembly|

SAFETY PRECAUTION

• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
• Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children unless they are aged 8 years and above and supervised.
• Do not try to repair the appliance on your own. Always contact an authorized technician. To avoid exposure to danger, always have faulty cable be replaced only by the manufacturer, by its customer service, or by a qualified person with a cable of the same type.
• The devices are not intended to be operated by an external timer or remote control system.

1. Make sure this appliance and the power cord are not damaged before operating. In case of damage, please consult your authorized technical service.
2. Do not fold and pull the wire.
3. Do not use it before complete assembly. Please make sure the blades and grids are fastened securely, and in general, that the unit is properly mounted.
4. Do not touch the appliance with wet or damp hands.
5. Please switch off the power before unplugging.
6. It is not allowed and dangerous to touch the water and any parts in the water when this appliance is working.
7. Do not insert any object into the guard and mist spray hole to avoid destroying this appliance. Do not use the fan in such places where the curtain may be drawn in.
8. The plug must be removed from the electrical outlet when not operating and before moving, installing, uninstalling, and cleaning. Unplug this appliance during lightning storms or when unused for long periods of time.
9. Do not pull the plug while the power is on. Always ensure that the plug is fully inserted into the electrical outlet before operating.
10. Do not take out the water tank before unplugging the power cord plug.
11. Do not add any chemical, or metal ingredient into the water tank or flume, these materials are dangerous and may cause problems.
12. The safety water level switch shall be cut off automatically when the water tank is lack water in order to protect the ultrasonic transducer. If need continuous working, please add water.
13. Baby, old people, and valetudinarianism are not fit directly under the fan wind for a long time.
14. This appliance must be used under the rated voltage and frequency as indicated in the rating label.
15. Do not disassemble, repair or modify this appliance on your own, the warranty shall be voided if repair is carried out by an unauthorized person/agency.
16. If the power cord is damaged, it must be replaced by the manufacturer or its service agent, or a similarly qualified person in order to avoid any hazard.
17. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
18. Children should be supervised to ensure that they do not play with the appliance.
19. Do not immerse the appliance in water or other liquids. Do not use near sources of water (sinks, baths, showers…)
20. Do not install the unit on uneven surfaces or where it could be subject to heat sources (e.g. radiators or stoves), direct sunlight, excessive dust, or mechanical vibrations.
21. If water is split on the floor, immediately wipe it up and dry the floor so as to prevent any injury from Slipping over, etc.

COMPONENTS

Before installation, please check that all parts have been supplied

1. Front grid
2. Blade spinner
3. Blades
4.Net frame
5. Plastic nut
6. Rear grid
7. Motor
8. Head angle knob| 9. Flexible hose
1 o. Indicator
11. Control buttons
12. Thumb screws
13. Power cord
14. Supporting tubes
15. Base + base cover
---|---

ASSEMBLY

BASE

1. Place the flat metal plate (with the two holes) in the recess.
2. Take the two support tubes and remove the screws from the ends. Enter the two tube ends through the plate holes.
3. Fit the washers and replace the two screws to fix the support tubes.
4. Put the base cover.

Base installation diagram

FAN HEAD/CONTROLLER

1. Loose the two thumbscrews located on the back of the fan head/controller. Do not fully unscrew otherwise the two nuts will fall off.
2. Locate the two holes on underneath the Fan Head /controller assembly onto the two tubes and push down until it stops.
3. Tighten the two Thumb Screws until they are secure.

FAN BLADE AND SAFETY GRID

1. Place the rear grid on the Fan Head, ensuring the wire handle on the back of the grid is at the top.
2. Screw the plastic nut to secure the grid.
3. Place the Fan blade onto the motor spindle.
4. Fix the blade into place by gently hand-tightening the spinner anticlockwise onto the end of the motor spindle. The spinner nut is self-tightening when the motor starts so do not force it.
5. Place the front grid into position and secure it by closing the secure clips. The screw and nut at the bottom of the grille must be fitted.

Note: Do not operate without fan grills and blades properly in place.
MIST GENERATOR AND WATER TANK

1. Place the misting generator onto the base, ensuring it is seated properly in its recess.
2. Put the water tank on top of the misting generator. Fit the cover to the top of the water tank.
3. Push the end of the flexible hose into the hole in the top of the water tank cover and push in as far as you can. (Do not kink the hose).
4. Push the other end of the hose to the mist vent located on the front of the fan grid (Do not kink the hose).

FILLING THE WATER TANK
Unplug the appliance before filling and cleaning.

1. Take the water tank and turn it upside down.

2. Unscrew the filler cap and lift it to remove it, and twist it anticlockwise to unlock it.

3. Fill with fresh clean water.

4. Refit the filler cap and turn it clockwise to lock it in place.
   Important: Ensure the tank cap is fully rotated and locked in place.
   DO NOT add any additives to the water.
   NOTE: Do not tamper with the valve in the filler cap.

5. Place the water tank back on top of the misting generator.
   Note: The carry handle on the water tank goes towards the back.

OPERATION

The mist fan has many functions that can either be controlled directly on the fan or via the remote control. To use the remote control, first, insert two MA

1. SV batteries in the remote control. Fill the fan’s water tank so that the ultrasound mist function can be used, then plug the fan into the main power.

2. “OFF “: press this button to switch the fan off.

3. “ON/SPEED”: Switch ON the fan and select fan speed:Low-Medium-High Cyclic selection

4. “MODE “: The wind mode can only be adjusted by using the remote control. Press “Mode” to set the speed (normal, sleep, natural).

5. “TIMER”: Setting working lime, Timer is 0.5H,1H,1.5H,2H,2 .5H,3H,3.5H,4H, 4.5H,5H,5.5H ,6H,6.SH,TH, 7.5H

6. “SWING”: When the fan is working, press the “SWING” button.
   The mist fan head moves continuously from side to side. Pressing the button again stops the oscillation of the mist fan.

7. “MIST”: Press the “Mist” button to switch the ultrasonic mist on I off.
   The remote controller is supplied without a battery.
   It uses a battery type LR03AAA 1.5V. Do not use other types of batteries.
   Make sure that the battery is installed correctly before using the remote controller.
   If the fan will not be used for a longer time, remove the battery from the remote.
   Do not dispose of your used battery in the garbage bin. Discard it in a suitable place for recycling batteries.

CLEANING AND MAINTENANCE

• Unplug the unit before cleaning.

• Any greasy dirt on the fan and fan blade should be cleaned with clean and mild detergent and a soft cloth.

• First, disassemble the fan (diagram 2).

• Clean the greasy dirt on the fan so as not to change the color or cause damage:
  – Clean with detergent and a soft cloth.
  – Avoid flushing with water directly.
  – Avoid cleaning with thinner, toluene, acids, kerosene, essential oils, and chemistry cloth so as not to change the color or cause damage.

• After cleaning, pack them in order and keep them in a dry place.

Maintenance of Cool Humidifier

1. Unplug the unit before cleaning.

2. Cleaning of the water tank (once a week)
   If there is dirt in the water tank, clean it with detergent and flush it with clean water.

3. Cleaning of Humidifier outside:
   Clean with a soft damp cloth, and clear the dirt. The mist cover must be cleaned carefully.

4. Notices of cleaning:

1. Do not touch the transducer with sharp tools, only clean it with a soft wet cloth.
2. Don’t use the cloth with chemical solvents gasoline • kerosene • polishing powder to wipe the fan’s appearance.
3. Don’t use detergent randomly, clear water is perfect. Avoid the water going in to cause malfunction.
4. Please don’t disassemble the unit fuselage or components randomly.

5. Keeping of Humidifier:
   When the unit is not used for a long time, clean it and put it in the packaging, and keep it in a dry place.

Notes:

1. Do not touch the transducer with sharp tools, only clean it with a soft wet cloth.
2. Don’t use the cloth with chemical solvents gasoline kerosene polishing powder to wipe the fan’s appearance.
3. Avoid the water going into the appliance, it can cause malfunction.
4. Keep the appliance clean.

When the unit is not used for a long time, clean it and put it in the packaging, and keep it in a dry place.

SIMPLE TROUBLESHOOTING

If your fan is not working properly, please check the following table before sending it to a service agent:

connected properly and the electric power is off.
2. The switch is off.| 1. Check whether the plug is inserted into the socket or connected well.
2. Check whether the switch is ON
The fan does not swing but has wind.| The SWING button is off| Whether the Oscillate switch is ON
The humidifier indicator light not working. No wind, No mist| 1. Plug not inserted properly
2. The power switch is turned off| I. Insert the plug properly 2. Switch power ON
The humidifier indicator light illuminates
Having wind but No mist| 1. No water in the water tank
2. Auto temperature knob is not open
3. The tank cover is not well placed| 1. Fill the tank with water
2. Open the auto temperature knob clockwise
3. Press the float cover well
The mist is smelly| 1. New product
2. Whether the water tank or water is cleaned| 1. Open the water tank for 12 hours in the cool place
2. Clean the water tank and change the water
The humidifier indicator light illuminates
No wind, No mist| Too much water in the tank| Replace the water and tighten the cover
The amount of mist is very small| 1. The transducer is clogged with dirt
2. Dirty water or water too long not replaced| 1. Clean the transducer
2. Replace clean water
Evident vibration| 1. The rearguard is not installed stably.
2. The blade cap is loose.
3. The blade is damaged.
4. The blade is off balance.| 1. Install the rear guard tightly.
2. Tighten the blade cap.
3. Replace the fan blade.
4. Turn the fan blade and re-install it.
Other unusual problems| 1. Smoke appears from the motor or there is a smell of burning.
2. The metal parts exposed to electricity or fan insulation are damaged.
3. The rear cover of the motor is damaged.| 1.2.3. Stop using the appliance and send it to a service agent for repair.

DISCARDING WORN HOUSEHOLD DEVICES
The European directive 2002/96/EC about electrical and electronic waste prohibits such household goods from being discarded with local refuse services. Worn devices must be collected separately to optimize the recovery and recycling rates of the components therein to reduce detrimental effects on the environment and human health.
The crossed-out rubbish bin symbol is affixed to all products as a reminder to respect the waste regulations.

ELITE EFM-1307R

Documents / Resources

| Elite EFM-1307R Water Mist Fan [pdf] User Manual
EFM-1307R Water Mist Fan, EFM-1307R, Water Mist Fan, Mist Fan, Fan
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>