AVTECHSMART AVALON100ZOOM 100W White LED Gobo Projector User Manual

June 4, 2024
AVTECHSMART

AVTECHSMART AVALON100ZOOM 100W White LED Gobo Projector

AVTECHSMART AVALON100ZOOM 100W White LED Gobo
Projector

Operate Introduction

4 MODES DMX mode, Auto run mode, Master/Slave, Manual mode

DMX Channels: 13 Channels
Function: Dimming, color wheel, rotating gobo wheel, focus, zoom, ripple effect, prism
4 menu buttons: ( Long press MODE+SET for 3 seconds to unlock, press MODE+SET in other interface to quickly lock)

MODE Menu/Back to previous menu
SETUP Confirm the selection function
UP Select the previous option
DOWN Select the next option

Menu

Menu 1 Menu 2 Menu 2 Functions
1.DMX Address 001- 512
2.Auto Mode Auto Run
Scene Edit Scenel-Scene 7 1.Dimmer: 0-255
2.Strobe: 0-255
3.Color: 0-255
4.ColorF: 0-255
5.Gobo: 0-255
6.Gobo_R: 0-255
7.Gobo F: 0-255
8.Focus: 0-255
9.Zoom: 0-255
10. Water: 0-255
11. Prism: 0-255
12. PrismR: 0-2555
13. Time: 0-255
3. Slave
4.Manual Control 1.Dimmer: 0-255
2.Strobe: 0-255
3.Color: 0-255
4.ColorF: 0-2555
5.Gobo: 0-255
6.Gobo_R: 0-255
7.Gobo F: 0-255
8.Focus: 0-255
9.Zoom: 0-255
10. Water: 0-255
11. Prism: 0-255
12. PrismR: 0-2555
--- --- --- ---
5.Settings l.Curve Select l.Linear
2.Square Law
3.lnvSquareLaw
4.S-Curve
2.DMX Fail Off
Hold
3.Display Normal
Inverted
4.Language English
Chinese
5.Key Lock Lock after 30s
Unlocked
6.Back Light Off after 60s
Always On
8.Default No
Yes
6.Calibrations Password l.Color: 000-255
2.Gobo: 000-255
3.GoboR: 000-255
4.Focus: 000-255
5.Water: 0-255
6.Zoom: 000-255
7. Prism: 0-255
8.Default:
7.lnformation version and UID code
  1. DMX Address
    Press the UP/DOWN button to set the initial address code (001 ~ 512). After setting the address code, press the SET button to confirm the save and automatically exit to return to the main menu. The fixture is in DMX mode after this operation.

  2. Auto Mode
    Select the Auto Mode menu, there are two menus for option, one is Auto Mode, another is Scene Edit with 7 scenes for editing. Each scene can be edited independently, and also includes all the DMX channels function and time- keeping function, but no
    Reset function. The editing process is the same as Manual Control, exit to save.
    This fixture has a maximum of 7 gobos, so it can set 7 scenes. If you need less than 8 scenes, set the scene time-keeping to “O”. The unit of time is seconds.

  3. Slave
    Select the Slave Mode menu, press the SET button to enter Slave Mode, then it will receive the signal from the master and keep the same state as the master. The fixture in Auto Mode or Manual mode is the master.
    In the screensaver, it will switch to DMX mode in response to the channel sent from the console whenever the master or slave receives the DMX512 signal.

  4. Manual Control
    Select the Manual Control menu, Press the UP/DOWN button to select which function to operate. The right number after pressing the SET button is selected. Then press the UP/DOWN button to modify the value, long press to continuously modify, and press the SET button to change the options on the left. Press the MODE button to exit and return to the main menu. It will not exit the manual mode in this state. It’s need to enter other modes for switching. For example, if you set the DMX address, then will enter the DMX mode.

  5. Settings

  6. Curve Select
    To choose one of linear dimming/square curve dimming/inverse square curve dimming/S-curve dimming. The characteristic of linear dimming is that the light output brightness maintains a linear relationship with the channel value; square curve dimming is relatively linear dimming, and the channel value range occupied in the low brightness area is more, that is the low brightness area is more abundantly adjusted; the low brightness area occupies few channels. When the channel value increases from 0 to up, the brightness quickly becomes very bright, and it allocates more channel value ranges in the high brightness area; the S-shaped curve is in the low brightness area Both the high-brightness area and the high-brightness area are allocated, and the medium-brightness area is few.

  7. DMX Fail
    “OFF” (No DMX, lighting is off.), “HOLD” (No DMX, lighting keeps the original state).

  8. Display
    The display reverse is used when the fixture is upside down.

  9. Language
    English or Chinese

  10. Key Lock
    When using the key lock function, not key operation after 30 seconds, the key is locked.
    Pressing the key in the locked state is invalid. It needs to press the MODE+SET key combination for 3 seconds to unlock.

  11. Back Light
    Select always on or 60S off if no operation

  12. Reset
    In order to verify whether the motor is working normally, and whether to save it after modifying the parameters, it can be perform a reset operation, like re-powering on.

  13. Default
    Restore the DMX address and parameters into factory values. The default address is 1, and the gray background option in the menu table is the default.

  14. Calibrations
    Enter 088 on the Password interface and press SET to enter the Calibrations menu.
    When the option on the left is selected, press the UP/DOWN button to select which function to operate. After pressing the SET button, the number on the right is in the selected state. At this time, press the UP/DOWN button to modify the value. Long press can be modified continuously. After pressing the SET button again, it changes back to the left option as the selected state. Press the SET button on the Default option to restore the default value 127.

  15. Information
    Display the fixture software version and UID code of RDM.

DMX Channel

Function DMX Value Setting 13 Channels
Dimmer 000-255 0~100% 1
Strobe 0-10 Always on 2
11-127 Random strobe slow to fast
128-255 Linear strobe slow to fast
Color 0~7 White 3
3~15 Color 1
15~23 Color 2
24~31 Color 3
32~39 Color 4
40~47 Color 5
43~55 Color 6
55~53 Color 7
54~71 white+ Color 1
72~79 Color 1+ Color 2
30~37 Color 2+ Color 3
33~95 Color 3+ Color 4
95~103 Color 4+ Color 5
104~111 Color 5+ Color 6
112~119 Color 6+ Color 7
120~127 Color 7+ white
128~191 Clockwise rotation: fast to slow
192~255 Counterclockwise rotation: slow to fast
Color F 0-255 Color wheel positioning fine-tuning 4
Gobo o~8 Gobo 1( or White circle) 5
9~17 Gobo 2
18~25 Gobo 3
27~35 Gobo 4
35~44 Gobo 5
45~53 Gobo 6
54~52 Gobo 7
53~71 Gobo 8
72~79 Gobo 8 shake from slow to fast
80~88 Gobo 7 shake from slow to fast
89~97 Gobo 6 shake from slow to fast
98~106 Gobo 5 shake from slow to fast
107~115 Gobo 4 shake from slow to fast
115~124 Gobo 3 shake from slow to fast
125~133 Gobo 2 shake from slow to fast
134~142 Gobo 1 not shake
143~199 Clockwise rotation fast to slow
200~255 Counterclockwise rotation slow to fast
Gobo R 0~127 Static rotation by a certain angle 6
128~191 Clockwise rotation fast to slow
192~255 Counterclockwise rotation slow to fast
Gobo F 0-255 Pattern positioning fine-tuning 7
Focus 0~255 Focusing 8
Zoom 0~255 Zooming 9
Water 0~127 No function 10
128-255 Ripple from slow to fast
Prism 0~31 Prism close 11
32~255 Prism open
Prism R 0~127 No rotate 12
128~191 Clockwise rotation fast to slow
192~255 Counterclockwise rotation slow to fast
Function o~9 No action 13
10~19 All reset after three seconds
20-255 No action

RDM Support

Readable Writable RDM Support Values description Customize
DISC_UNIQUE_BRANCH 0x000l Search
DISC MUTE 0x0002 Locked
DISC UN MUTE 0x0003 Unlock
v SUPPORTED- PARAMETERS 0x00S0 Supported Parameters

v

| | PARAMETER_DESCRIPTION| 0x00Sl| Custom parameter description|
v| | DEVICE- INFO| 0x0060| Device information|
v| | DEVICE_MODEL_DESCRIPTION| 0x0080| Device model no. description|
v| | MANUFACTURER_LABEL| 0x0081| Manufacturer|
v| v| DEVICE_LABEL| 0x0082| Device label|
v| v| FACTORY_DEFAULTS| 0x0090| Factory setting|


v

| | LANGUAGE_CAPABILITIES| 0x00A0| Languages capabilities|
v| v| LANGUAGE| 0x00B0| Languages|


v

| | SOFTWARE- VERSION- LABEL| 0x00CO| Software version description|
v| v| DMX- START- ADDRESS| 0x00F0| DMX Start Address|
v| | SENSOR DEFINITION| 0x0200| Sensor Definition|
v| v| SENSOR VALUE| 0x0201| Sensor value|
| v| RECORD SENSORS| 0x0202| Record sensor value|
v| v| DISPLAY INVER| 0x0S00| Display reversed|
v| v| IDENTIFY DEVICE| 0xlO00| Identify device|
| v| RESET DEVICE| 0xlO0l| Reset Device|
| v| CAPTURE_PRESET| 0x1030| Preset|
v| v| PRESET_PLAYBACK| 0x1031| Playback|
v| v| FAC_RUN_MODE| 0xD320| Lamp Operation Mode|
| v| FAC_SAVE_RUN_MODE| 0xD321| Save run mode|

  • Lamp operating mode description: The data is 1 byte unsigned number, 0 means DMX mode, 1 means manual control mode, 2 means self-propelled mode, 3 means slave mode.
    *Save operation mode description: The 0xD320 instruction is only a temporary modification of the operation mode. It needs to be saved with the 0xD321 instruction. Write 1 to save the current operation mode, and write Oto restore the previously stored operation mode.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals