Shark HC500/HC450 Series Air Purifier 3-in-1 with True HEPA User Manual

Shark HC500/HC450 Series Air Purifier 3-in-1 with True HEPA User Manual

OWNER’S GUIDE

Read and review instructions for operation and use.

Indicates the presence of a hazard that can cause personal injury, death, or substantial property damage if the warning included with this symbol is ignored.
For indoor and household use only.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic safety precautions should always be followed, including the following: HOUSEHOLD USE ONLY

WARNING:

1. Read all instructions before use.

2. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT attempt to defeat this safety feature. Unplug or disconnect the appliance from the power supply before servicing.

3. DO NOT operate any appliance with a damaged cord or plug. Discard appliance or return to an authorized service facility for examination and/or repair.

4. DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or similar coverings. DO NOT route cord under furniture or appliances. Keep cord away from high traffic areas and place cord where it will not be tripped over.

5. If the power cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.

6. This appliance is not intended for use by anyone (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

7. Children should be supervised to ensure that they DO NOT play with the appliance.

8. Cleaning and user maintenance shall not be made by children
   without supervision.

9. Prior to cleaning or other maintenance, the appliance must be unplugged from the electrical outlet.

10. DO NOT handle plug or appliance with wet hands.

11. DO NOT use without filter in place.

12. Only use Shark” branded filters and accessories.

13. DO NOT damage the power cord:
    a) DO NOT pull or carry appliance by the cord or use the cord as a handle. b) DO NOT unplug by pulling on cord. Grasp the plug, not the cord. c) DO NOT stand the appliance on the power cord, close a door on the cord, pull the cord around sharp corners, or leave the cord near heated surfaces.

14. DO NOT use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow.

15. DO NOT use if airflow is restricted. If the air paths become blocked, turn the appliance off and unplug from electrical outlet. Remove all obstructions before you plug in and turn on the unit again.

16. DO NOT use if appliance is not working as it should, or has been dropped, damaged, left outdoors, or dropped into water.

17. DO NOT place appliance on unstable surfaces such as chairs or other furniture.

18. DO NOT use in the following areas:
    a) Wet or damp surfaces
    b) Outdoor areas
    c) Spaces that are enclosed and may contain explosive or toxic fumes or vapors (lighter fluid, gasoline, kerosene, paint, paint thinners, mothproofing substances, or flammable dust)

19. Turn off all controls before unplugging the appliance.

20. Unplug from electrical outlet when not in use and before any maintenance or cleaning.

21. Hand wash with soapy water only. Washing with cleaning chemicals could damage the unit.

22. Make sure filter is in place after routine maintenance.

23. Not suitable for use with solid-state speed controls.

IMPORTANT INSTRUCTIONS

1. This heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater and keep them away from the sides and rear.
2. Extreme caution is necessary when any heater is used by or near children or persons with disabilities and whenever the heater is left operating and unattended.
3. This heater is not intended for use in bathrooms, laundry areas, or other high moisture locations. Never locate heater where it may fall into a bathtub or other water container.
4. DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
5. To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. DO NOT use on soft surfaces, like a bed, where openings may become blocked.
6. A heater has hot, arcing and/or sparking parts inside. DO NOT use it in areas where gasoline, paint, or flammable liquids are used or stored.
7. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
8. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).

WARNING: LITHIUM BATTERY

1. Dispose of coin cell batteries according to local regulations. Keep batteries away from children at all times. Even used batteries can cause injury.
2. Chemical Burn Hazard. Keep batteries away from children.
   This product contains a lithium button/coin cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. After changing batteries, always completely close and secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the battery, and keep it away from children. If you think battery might have been swallowed or placed inside any part of the body, seek immediate medical attention.

SCAN FOR ADDITIONAL RESOURCES

OR VISIT qr.sharkclean.com/ hcSOOseries

SETTING UP YOUR UNIT

TIPS FOR SETTING UP YOUR UNIT

• Orient the unit with display facing away from the wall.

• Do not move the unit while it is running.
  Turn off the power and unplug the unit before moving it.

• Make sure the vents are not blocked.

• Do not place anything on the appliance.

• Do not place the appliance near heaters or radiators.

• Keep the unit out of direct sunlight and away from water or other liquid.

• Keep all nearby doors and windows closed when operating the air purifier.

• Avoid using in very humid environments.

SETTING UP YOUR AIR PURIFIER

1. You must remove the filter and take it out of its packaging before operating. First, remove the filter cover and filter from the back of the air purifier.

2. Take the filter out of its sealed plastic packaging. Slide filter back into the air purifier.

3. Reinstall the filter cover. Insert the tabs on the bottom of the cover into the slots. Press the top and sides of the cover until it clicks into place.

4. Set up the air purifier on a level floor surface at least 3 feet (0.9m) from the wall and any furnishings.
When carrying the air purifier, hold it below the venting area. Do not put your hands inside the vents

5. Plug the unit into an electrical outlet and press the power button on the top control panel OR on the removable remote.

6. When the air purifier is powered on, it will begin to analyze the air quality, indicated by the rotating lights.
After a few seconds, the air purifier will display the current air quality and room temperature. From there, use the remote and dial to customize the settings.

REMOTE

You can use the removable remote control to customize the settings.

REMOTE SHORTCUTS

Turn Off Sound: To turn off sounds, press and hold the Brightness button for 3 seconds.

Turn On/Off Child Safety Lock: Press and hold the Timer and Oscillation buttons to turn the Child Safety Lock on or off. The Lock icon will appear on the front display when the lock is activated.

Change Temperature Display from Fahrenheit to Celsius: Press and hold Fan and Thermometer buttons to change the temperature display from Fahrenheit to Celsius.

Reset Filter Life: Press and hold the info button for 3 seconds to reset the Filter Life display after changing the filter.

On/Off: Press to turn the power on or off.

AUTO mode: Press to turn on AUTO mode. The fan speed automatically adjusts, based on the air quality. As the air quality improves, the fan speed will decrease. If air quality worsens, the fan speed will increase. Leave your air purifier in AUTO mode for optimal filter life and performance. AUTO mode is only available in PURIFIED AIR mode.

Optimize Performance in ECO mode: After the air is 100% clean for 10 minutes, the air purifier will enter ECO mode and @ will appear on the display. This reduces power draw and optimizes the filter life.

Air Info: Press to switch between air quality display options.
See the Air Info Settings section for more information.

Fan Controls: Use the arrows to adjust the fan speed from 1-6.
Press the fan button to view the speed setting. Fan speed can be adjusted in all 3 modes.

Note: When using AUTO mode, if fan speed is manually changed, AUTO mode will be deactivated. For tips on optimal fan setting, see Optimizing Fan Speed section.

Heater Controls: Press the Thermometer button to turn HEAT on/off. Target

Temperature: Use the arrows to adjust the target temperature. The heater will automatically work to reach and maintain the target. The air purifier will beep when the target temperature is reached.

HI HEAT Mode: To run the heater in HI HEAT mode without selecting a target temperature, press and hold the right-side temperature arrow until HI appears on the display. For more tips on optimizing heater performance, see the Heater Operation section.

Shut-Off Timer: Set the number of hours for the air purifier to run before it automatically shuts off. Timer can be set from 1-12 hours.

Brightness: Press to dim the brightness of the display. Switch between 3 options: full brightness, partially dim, or fully dim.

Oscillation: Press to turn the oscillation on or off. When oscillating, the unit will rotate side to side to distribute airflow around the room.

MODE DIAL

Turn the dial to change modes.

1. PURIFIED FAN

To operate FAN mode, turn the dial to the Fan icon. In this mode, purified air will be directed out of the front vents.

2. PURIFIED HEAT

To operate HEAT mode, turn the dial to the Air icon. Then press the Thermometer! button on remote. In this mode, purified, warm air will be directed out of the front vents.

3. PURIFIED AIR
To operate PURIFIED AIR mode, turn the mode dial to the Air icon. In this mode, purified air will be diffused out the back vents. This allows for continuous air purification without the breeze of a fan.

While the air will be purified in all modes, PURIFIED AIR mode boosts cleaning power.

PURIFIED AIR mode is compatible with AUTO and ECO modes

MODE DISPLAYS

THE INFORMATION ON THE FRONT DISPLAY IS DIFFERENT IN EACH MODE.

PURIFIED FAN

The top reading is the clean air percentage and the bottom reading is the current room temperature.

PURIFIED HEAT
In this mode, the top reading is the clean air percentage and the bottom reading in red is the target temperature. Once the target temperature is reached, the bottom reading will display the current room temperature in white.

PURIFIED AIR
In this mode, the percentage of clean air is shown.

UNDERSTANDING YOUR AIR QUALITY

The ring around the display will change color as the air quality changes, for easy monitoring from far away.

Note: The air quality sensor uses a cumulative particle count across all particle sizes to determine percentage of clean air.

AIR INFO SETTINGS
The built-in sensor detects your air quality to give you real-time information. Use the AIR INFO button CD to switch between settings.

AIR PURIFIER OPERATION

TO ACTIVATE PURIFIED AIR MODE AND ADJUST SETTINGS:

1. Turn the mode dial to the Air icon.
2. The display will show air quality as a percentage. Press CD the info button to change the air information displayed.
3. Press the fan arrows to adjust the fan speed. As fan speed increases, so will purification performance.

4. To activate AUTO mode, press the AUTO button. In this mode, the fan speed will automatically adjust, based on the quality of the air. AUTO mode is only available in PURIFIED AIR mode.
5. When in AUTO mode, if the air is 100% clean for 10 minutes, the air purifier will enter ECO mode and ® will appear on the display. This will reduce energy consumption and extend the filter life.

TIPS FOR USING PURIFIED AIR MODE:

Air quality fluctuates, depending on what is introduced in the home. Some factors that can affect the air quality:

• Cooking or burning food
• Vacuuming or dusting
• Spraying cleaning products
• Smoking
• Opening windows or exterior doors can introduce pollen.

Leave the air purifier in AUTO mode for optimal filter life and performance.

AUTO mode is ONLY available in PURIFIED AIR mode.

FAN OPERATION

TO ACTIVATE THE FAN AND ADJUST AIRFLOW:

1. Turn the mode dial to the Fan icon.
2. On the front display, the top number is the clean air percentage and the bottom number is the current room temperature. Press CD the Info button to change the air information displayed.
3. Press the fan arrows to adjust the fan speed or press the Fan button to check current fan speed. As fan speed increases, so will purification performance.

4. Press the O Oscillation button on the remote to turn oscillation on or off.
5. Additionally, the airflow angle can be adjusted by moving the front vents up or down.

NIGHT USE

For non-disruptive performance at night:

• Lower the fan speed for soothing white noise.
• Press the 3?’.- Brightness button to fully dim the display.
• Turn on oscillation for better fan coverage.
• Press and hold the-*- Brightness button for 3 seconds to turn sound off or on.

HEATER OPERATION

TO ACTIVATE THE HEATER AND ADJUST SETTINGS:

1. Turn the mode dial to the Heat icon and press A to turn on heat.
2. On the front display, the top number is the clean air percentage. The bottom number in red is the target temperature.
3. Press the temperature arrows to set the target temperature or hold down the right arrow for HI heat mode. When the target temperature is set, the display will flash and beep twice to confirm.

Note: The heater may need up to 25 seconds to fully warm up. This will be indicated by the red ‘heating up’ animation.

4.After the target temperature is set and the heater is active, the bottom number in the display will turn white and will update to show current room temperature.
S. When the target temperature is reached, there will be a long beep, and heating will pause.
6. Use the fan arrows to adjust the heated air flow rate.
7. Press the Info CD button to change the air information display.
8. Press the Oscillation icon to turn oscillation on or off.
9. Additionally, the airflow angle can be adjusted by moving the front vents up or down.

TIPS FOR USING PURIFIED HEAT MODE

• When using the air purifier at close range for personal heating, lower the fan speed for optimal performance.
• When using the air purifier at a distance for whole-room heating, increase the fan speed and turn on oscillation for optimal performance.
• In HI heat mode, the heater will not have a temperature target and will continue to run until turned off.

HEATER SAFETY FUNCTION AND RESET

The air purifier has multiple safety features designed to prevent overheating, accidents, and damage.

TIP-OVER AUTOMATIC SHUTOFF
If your air purifier gets tipped over, it will automatically turn off. Follow these steps to reactivate the heater:

1. Turn the power off and unplug the air purifier.
2. Set the air purifier upright, on a level floor surface.
3. Plug in the air purifier and turn on power.
4. Turn the mode dial to the Heat icon and press to turn on heat.

OVERHEAT AUTOMATIC SHUTOFF
Your air purifier could overheat if obstructions block the vents. If this happens, the unit will automatically turn off. Follow these steps to reactivate the heater:

1. Turn the power off and unplug the air purifier.
2. Remove any obstructions from the vents.
3. Wait 5 minutes, then plug in the air purifier and turn on power.
4. Turn the mode dial to the Heat icon and press to turn on heat.

INSTALLING AND REMOVING THE FILTER

NOTE: Always remove all protective packaging from the filter before installing.

Shark® filters are engineered to last between 6-12 months. When the filter life has 0% remaining, FILTER LIFE will illuminate and flash, indicating that it’s time to install a new filter.

1. Turn off and unplug the air purifier before removing or installing filters.
2. First, remove the filter cover from the back of the air purifier. Use the handle to pull the filter door towards you.
3. To remove the old filter, pull it out by the removal tabs. Discard old filter in trash.
4. Remove all packaging and wrapping from the new filter.

5. Insert the new filter, then replace the filter cover. Insert the tabs on the bottom of the cover into the slots. Press the top and sides of the cover until it clicks into place.
6. Plug the air purifier back on and turn on power.
Calibration will begin.
7. After installing a new filter, press and hold the G) Info button
for 3 seconds to reset the filter life percentage. The air purifier will beep to confirm when the filter life is reset to 100%.

Disposing of used filters
Filters can’t be cleaned or recycled. After removing a used filter, wrap it in an airtight plastic bag for disposal. As an extra precaution, wear gloves when handling a dirty filter.
To maximize filter life , every three months, remove the filter, then turn it upside down and reinstall it. This will help equalize and balance the distribution of captured particles throughout the filter, allowing for extended use.

MAINTAINING YOUR AIR PURIFIER

NOTE: Always unplug the unit before doing any cleaning or maintenance.

Exterior Cleaning:
For best results, clean the exterior of the air purifier every two months or as needed. Use a microfiber cloth to remove dust. To sanitize, wipe down the exterior with a microfiber cloth dampened with warm, soapy water. Avoid excess water and abrasive chemical cleaners to prevent damage.

Interior Cleaning:
For best results, clean the interior of the unit every two months or as needed. Remove the filter cover, take out the filter, and use a vacuum cleaner or a microfiber cloth to remove dust and debris from the interior of the air purifier. DO NOT use abrasive chemical cleaners on the inside of the air purifier.

REPLACING THE REMOTE BATTERY

The removable remote is equipped with a CR2025 lithium coin cell battery with a life of up to 3 years. Periodically, the remote battery will require replacement.

1. Remove the remote from its dock on the top of the air purifier.

2 Pinch the tab on the battery compartment, then slide out the compartment.

3. Remove the battery and dispose of it immediately. Keep the battery away from children and pets.

4. Insert a new battery,(+) side facing up. Then slide the battery compartment back into the remote, until it clicks into place.
5. Point the remote at the air purifier and adjust the settings to
ensure the remote is functioning properly. If there are persisting issues with the remote, see the Troubleshooting section.

AVAILABLE ACCESSORIES

ORDER ADDITIONAL ACCESSORIES AND REPLACEMENT FILTERS from sharkaccessories.com

SHARK® NANOSEAL™ BASE FILTER WITH TRUE HEPA
Captures 99.98% of large, small, and micro-sized particles from the air and is equipped with carbon for heightened protection against household odors and VOCs.

SHARK® HCS00/450 SERIES REMOTE CONTROL.

SHARK® NANOSEAL™ BASE FILTER WITH TRUE HEPA+ MICROBAN
Captures 99.98% of large, small, and micro-sized particles from the air and is equipped with carbon for heightened protection against household odors and VOCs.

TREATED WITH MICROBAN:
Additional antimicrobial protection with Microban treatment. Microban reduces the bacterial growth on the HEPA surface.

TROUBLESHOOTING

Customer Service
For further assistance, call 1-855-523-4061.

TWO (2) YEAR LIMITED WARRANTY

The Two (2) Year Limited Warranty applies to purchases made from authorized retailers of SharkNinja Operating LLC. Warranty coverage applies to the original owner and to the original product only and is not transferable.
SharkNinja warrants that the unit shall be free from defects in material and workmanship for a period of two (2) years from the date of purchase when it is used under normal household conditions and maintained according to the requirements outlined in the Owner’s Guide, subject to the following conditions and exclusions:

What is covered by this warranty?

1. The original air purifier and/or non-wearable parts deemed defective, in SharkNinja’s sole discretion, will be repaired or replaced up to two (2) years from the original purchase date.
2. In the event a replacement unit is issued, the warranty coverage ends six (6) months following the receipt date of the replacement unit or the remainder of the existing warranty, whichever is later. SharkNinja reserves the right to replace the unit with one of equal or greater value.

What is not covered by this warranty?

1. Normal wear and tear of wearable parts (such as filters and batteries, etc.), which require regular maintenance and/or replacement to ensure the proper functioning of your unit, are not covered by this warranty. Replacement parts are available for purchase at sharkaccessories.com.
2. Any air purifier that has been tampered with or used for commercial purposes.
3. Damage caused by misuse, abuse, negligent handling, failure to perform required maintenance (e.g., not replacing the filters), or damage due to mishandling in transit.
4. Consequential and incidental damages.

5. Defects caused by repair persons not authorized by SharkNinja. These defects include damages caused in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts) when the repair is performed by a repair person not authorized by SharkNinja.
6. Products purchased, used, or operated outside North America.

How to get service
If your air purifier fails to operate properly while in use under normal household conditions within the warranty period, visit sharkclean.com/ support for product care and maintenance self-help. Our Customer Service Specialists are also available at 1-855-523-4061 to assist with product support and warranty service options, including the possibility of upgrading to our VIP warranty service options for select product categories. So we may better assist you, please register your product online at registeryourshark.com and have the product on hand when you call.
SharkNinja will cover the cost for the customer to send in the unit to us for repair or replacement. A fee of $25.95 (subject to change) will be charged when SharkNinja ships the repaired or replacement unit.

How to initiate a warranty claim
You must call 1-855-523-4061 to initiate a warranty claim. You will need the receipt as proof of purchase. We also ask that you register your product on line at registeryourshark.com and have the product on hand when you call, so we may better assist you. A Customer Service Specialist will provide you with return and packing instruction information.

How state law applies
This warranty gives you specific legal rights, and you also may have other rights that vary from state to state. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.

IMPORTANT INFORMATION

REGISTER YOUR PURCHASE

• registeryourshark.com
• Scan QR code using mobile device

RECORD THIS INFORMATION
Model Number: ____

Serial Number: __
Date of Purchase: ____ (Keep receipt)
Store of Purchase: ____ _

TECHNICAL SPECIFICATIONS

Voltage: 120V~ 60Hz
Watts: 1500W

Benefits of registering your product and creating an account:

• Get easier, faster product support and access to warranty information
• Access troubleshooting and product care instructions
• Be among the first to know about exclusive product promotions

BATTERY REMOVAL AND DISPOSAL
This product’s remote control uses a lithium button battery. When the battery no longer has a charge, it should be removed from the remote and recycled. DO NOT incinerate or compost the battery.

When your lithium battery needs to be replaced, dispose of it or recycle it in accordance with local ordinances or regulations. In some areas, it is illegal to place spent lithium batteries in the trash or in a municipal solid waste stream. Return spent battery to an authorized recycling center or to retailer for recycling. Contact your local recycling center for information on where to drop off the spent battery.

FCC WARNINGS
Note: This unit has been tested and found to comply with FCC limits for Class B digital devices. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This unit generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
To see if this unit interferes with radio or television reception, try turning it off and on.

To correct any interference:

• Reorient or relocate the receiving antenna.
• Increase the distance between the unit and the receiver .
• Connect the unit to a different outlet than the receiver.
• Consult the dealer or an experienced technician for help.

Caution: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate it.

TIP: You can find the model and serial numbers on the QR code label on the bottom of the unit.

PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.
This Owner’s Guide is designed to help you get a complete understanding of your new Shark® Air Purifier.
SharkNinja Operating LLC
US: Needham, MA 02494
CAN: Ville St-Laurent, QC H4S 1A7

1-800-798-7398

sharkclean.com

Illustrations may differ from actual product. We are constantly striving to improve our products; therefore the specifications contained herein are subject to change without notice.

This product may be covered by one or more U.S. patents. See sharkninja.com/patents for more information.

© 2022 SharkNinja Operating LLC. SHARK is a registered trademark of SharkNinja Operating LLC.

SHARK NANOSEAL is a trademark of SharkNinja Operating LLC.

HC500/450 Series Shark® Air Purifier 3-in-1 with True HEPA FAQs

This article contains the FAQs for the HC500/450 Series Shark® Air Purifier 3-in-1 with True HEPA.  This supports the following SKUs: HC450, HC452, HC452C, HC455, HC501, HC502 and HC502C.

General Questions

How do I set up my air purifier?

1. Set up the air purifier on its base on a level floor. For best results, set it up in the space you spend the most time in, such as the kitchen, living room, or bedroom. Make sure the air purifier is at least 3 feet (0.9 m) away from all walls, large objects, or electronics.
2. Before plugging in the air purifier for the first time, you must remove the filter and take it out of its packaging. First, open the filter door on the backside of the air purifier.
3. Remove the filter from the air purifier and take it out of its sealed plastic packaging. Then, reinstall it into the air purifier. DO NOT run the air purifier unless the filter is removed from its packaging and installed correctly.
4. With the filter installed, replace the filter door.
5. Plug the air purifier into an electrical outlet and press the power button on either the top of the air purifier or on the remote to power on.
6. Once the air purifier is turned on, it will begin to read the air quality in your room. This calibration process will run for a few seconds and is indicated by the rotating lights the front display. Once the calibration is complete, you can begin to customize the settings on your air purifier.

Where is the best place to put my air purifier?

To benefit the most from your 3-in-1 Air Purifier, Shark® recommends placing the air purifier in the room where you spend the most time. Be sure that the air purifier is placed on a flat surface, near an outlet, and away from other furniture or items in order to keep the intake vents clear. For maximum air flow, keep the air purifier at least 3 feet (0.9 m) away from the wall.

Does this air purifier have a HEPA filter?

Yes, this air purifier features a Shark® Nanoseal™ filter with True HEPA that captures 99.98% of particles down to the 0.1–0.2 micron range.

What is PM?

M stands for “particulate matter.” This term refers to microscopic solids or liquid droplets that are suspended in air and can cause serious health problems if inhaled. Using Clean Sense IQ™, the Shark®™ Air Purifier tracks 3 distinct sizes of particulate matter: PM1.0, PM2.5, and PM10. Each of these particulate sizes corresponds to common household pollutants. PM1.0 includes ultra-fine allergens and viruses. PM2.5 includes smoke and bacteria. PM10 includes dust, pollen, and mold.

What accessories are included with my air purifier?

Your Shark® 3-in-1 Air Purifier comes with 1 pre-installed filter. Please be sure to remove the filter from its packaging before initial use.

Can I leave my air purifier on at all times (24/7)? How does that affect lifespan of the product?

While your air purifier can be left running 24/7, longer runtimes may shorten the filter lifespan. Shark® recommends keeping your air purifier in Purified Air AUTO mode to optimize the filter life. To enable, turn the dial toward the Purified Air icon and the air will now be diffused out of the back of the air purifier.
After 100% clean air status is achieved for 10 minutes in AUTO mode, your air purifier will enter ECO mode and further optimize your filter life.

Where can I find the remote?

The remote can be found nested on top of the air purifier. This control panel style remote can be removed from the air purifier body to be used as a portable remote. When using the control panel as a remote, be sure to point it toward the front display screen for best results.

What if I lose my remote?

To order a new remote, please visit Sharkaccessories.com

What type of battery does the remote require?

The battery for the 3-in-1 Air Purifier remote is a CR2025 lithium coin cell battery.

General Questions about using the Air Purifier

How does this product clean my air?

The Shark® 3-in-1 Air Purifier is equipped with a 3-stage HEPA filter that is designed to capture 99.98% of particles down to the 0.1–0.2 micron range, plus odors and VOCs. The cylindrical structure pulls air through the back and sides of the air purifier and passes it through the HEPA filter. Particles such as smoke, mold, and allergens are then trapped in the HEPA filter, allowing only clean air to be passed through the top vents.

How can I tell if my air is clean?

The illuminated air quality ring on the front display will change color as your air quality changes. The color of the ring indicates the air quality: Blue = Good air quality, Amber = Fair air quality, Red = Poor air quality. By pressing the AIR INFO button on your air purifier, you can switch between air quality info options. These include percentage of clean air, estimated time until the air will be clean, and the estimated number of PM1.0, PM2.5, and PM10 particles in the air surrounding the air purifier.
When enabled in Purified Air mode, the AUTO mode setting automatically adjusts the fan speed of your air purifier based on the air quality. (If the air quality decreases, the fan speed will increase.) To activate AUTO mode, make sure the side dial on the air purifier is turn toward the purified air icon. Press the AUTO button on the remote. When this option is selected, the AUTO icon will appear on your front display. To turn off AUTO mode, press the AUTO button again or manually change the fan speed.

Does this air purifier reduce odors?

Yes, the Shark® 3-in-1 Air Purifier filter is equipped with activated carbon. This is designed to absorb household odors and VOCs (volatile organic compounds) such as formaldehyde, acetone, and butanol. Depending on the model purchased, the type of filter may vary.

General Questions about Air Quality

Why is my air quality always at 100%?

If your air purifier display reads 100%, your air quality is good. However, air quality will fluctuate as you introduce pollutants into your home. Activities like smoking, cooking, dusting, or spraying cleaning products (among other things) can add more pollutants to your air. Clean Sense IQ™ tracks this fluctuation in real time and alerts you when your air quality decreases. Air quality is measured by the amount of particulate matter in your air. To accurately calculate the percentage of air that is clean, Clean Sense IQ™ tracks 3 distinct particle sizes: PM1.0, PM2.5, and PM10. However, particles in your air can be both larger and smaller than this range. Rest assured, our Nanoseal™ True HEPA technology is cleaning the air by capturing odors and 99.98% of particles down to the 0.1–0.2 micron range.

Why is my air quality never at 100%?

If your air quality never reaches 100%, make sure that the filter is properly installed without its original plastic packaging. If the filter is properly installed, then it may need replacement. Note that the filter generally requires replacement every 6–12 months, but if a high amount of particulate matter is regularly present in your air, you may need to replace the filter more often. Activities like smoking, burning candles, running a humidifier, opening windows, and cooking (among other things) can add more pollutants to your air. Make sure to survey your environment and remove anything that could be causing low air quality.

Why is my air quality at 100%, but the air smells bad?

Air quality is measured by the amount of particulate matter in your air. To accurately calculate the percentage of air that is clean, Clean Sense IQ™ tracks 3 distinct particle sizes: PM1.0, PM2.5, and PM10. However, odors are not included in this calculation. Rest assured, our Nanoseal™ True HEPA technology is actively capturing odors and VOCs while you run your air purifier.

Why is my air quality reduced even when I am not cooking or doing anything unusual?

Air quality can change for a variety of reasons. Even everyday activities can agitate particles (such as previously settled dust) into the air, which will decrease air quality. Clean Sense IQ™ does a reading of microscopic particulate matter in the room and displays the air quality accordingly.

General Questions about Features

What is AUTO mode and when should I use it?

When enabled in Purified Air mode only, the AUTO mode setting automatically adjusts the fan speed of your air purifier based on the air quality. (If the air quality decreases, the fan speed will increase.) To activate AUTO mode, make sure the side dial on the air purifier is turn toward the purified air icon. Press the AUTO button on the remote. When this option is selected, the AUTO icon will appear on your front display. To turn off AUTO mode, press the AUTO button again or manually change the fan speed.

How do I mute the beeping?

To mute your air purifier’s beeping, hold the BRIGHTNESS button for 1.5 seconds. You will hear auditory feedback (3 beeps) once the setting is confirmed. The beeps are now muted.

How do I unmute the beeping?

To unmute your air purifier’s beeping, hold the BRIGHTNESS button for 1.5 seconds. You will hear auditory feedback (3 beeps) once the setting is confirmed. The beeps are now unmuted.

How do I enable child lock?

To enable the child lock setting and lock the remote buttons, hold the TIMER and OSCILLATION buttons at the same time for 1.5 seconds. You will hear auditory feedback once the setting is confirmed. The control panel is now locked.

How do I disable child lock?

To disable the child lock setting and unlock the remote buttons, hold the TIMER and OSCILLATION buttons at the same time for 1.5 seconds. You will hear auditory feedback once the setting is confirmed. The control panel is now unlocked.

How does the dim setting work?

The brightness button adjusts the brightness of the front display screen. Press the button to switch between 3 options: full brightness, partially dim, and fully dim.

General Questions about Maintanence

How do I maintain my air purifier?

Both the exterior and the interior of your air purifier will need to be dusted periodically. For best results, clean the air purifier every two months or more often if necessary. When cleaning dust from the exterior, use a microfiber cloth to remove debris from the surface of the air purifier. To sanitize, wipe down the exterior with a warm, soapy cloth. Avoid excess water and abrasive chemical cleaners to prevent damage. When cleaning dust from the interior, lift off the filter cover, remove the filter, and use a vacuum cleaner or a microfiber cloth to remove dust and debris from the interior of the air purifier. DO NOT use abrasive chemical cleaners on the inside of the air purifier. DO NOT insert cleaning instruments into the fan outlet.

How do I optimize my filter life?

To maximize your air purifier’s filter life and performance, Shark® recommends leaving your air purifier in AUTO mode. After 100% clean air status is achieved for 10 minutes in AUTO mode, your air purifier will enter ECO mode and further optimize your filter life. Shark®™ also recommends flipping and rotating the direction of your filter every 3 months. This will help equalize and balance the distribution of captured particles throughout the filter, allowing for extended usage.

How often do I need to replace the filter?

Shark® recommends changing the filter every 6–12 months. When the filter needs to be changed, the FILTER LIFE text will flash on the front display. If you or a member of your household is sensitive to allergens, you may benefit from changing the filter more frequently. To check the remaining filter lifespan, press the Info button on the remote until your display shows the filter life air quality view. This is the percentage of filter life remaining before the filter needs to be changed.

Can I wash the filter?

No, the filter is not washable. Keep the filter away from water and dispose of it when dirty.

Can I use any replacement filter?

Only use Shark® brand filters when operating your air purifier. Other filters may cause damage to your air purifier. There are multiple different size and shape Shark® filters.
For HC450 series air purifiers, the following filters are compatible: HE1FKBAS, HE1FKBASMB, HE1FKPET.
For HC500 series air purifiers, the following filters are compatible: HE2FKBAS, HE2FKBASMB, HE2FKPET.
Replacement filters can be purchased at Sharkaccessories.com.

Where can I buy replacement filters?

Replacement filters can be purchased at www.Sharkaccessories.com.

Product Specifications

What is the wattage?

1500 watts

What is the Amperage?

12.5 Amps

What is the Voltage?

120 volts

What is the cord length?

The cord is 6 feet long.

What is the weight?

12.78 lbs

What is the Dimensions?

10.43(L)x10.43(W)x23.6(H)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>