GRS 003-530 Standard Block Ball Vise Instruction Manual

GRS 003-530 Standard Block Ball Vise

Product Information

The product is a work holding tool designed to solve work holding problems and assist users in their work. It comes with a variety of pins that fit the upper jaw plates of every block, allowing users to start working sooner. The package includes the following pins:

• 8 small pins
• 4 flat square pins
• 2 rectangular inset-curve pins
• 4 thick round inset pins
• 8 rubber-coated pins
• 2 leather-faced ring clamp pins

All of these pins are stored in a molded base for easy organization and access.

Product Usage Instructions

1. Inspect the product for any damage or defects before use. Do not use if there are any visible issues.
2. Select the appropriate pin from the range provided based on your work holding requirements.
3. Insert the chosen pin into the upper jaw plate of the block, ensuring it is securely in place.
4. Repeat the above steps if multiple pins are needed for your work holding setup.
5. If using rubber-coated or leather-faced pins, ensure that the coated or faced side is in contact with the workpiece for better grip and protection.
6. Once the pins are securely in place, you can start working on your project.
7. After use, remove the pins from the upper jaw plates and store them back in the molded base for future use.
8. Clean the pins and the tool as necessary to maintain their effectiveness and longevity.

If you have any further questions or concerns regarding the product or its usage, please refer to the manufacturer’s contact information provided below:

Standard Block Ball Vise Complete Assembly #003-530

Ring Clamps
These leather-faced ring clamps let GRS ball vises hold rings securely from the outside so you can set stones, bright cut, engrave and finish them using your block. These clamps also come with the 30-Piece Attachment Set. Includes two clamps.

Standard Block Ball Vise For Engraving and Jewelry Making
INSTRUCTIONS   #003-530

Standard Block will provide many years of trouble-free service. It is extremely rugged in construction, yet is relatively simple and easy to maintain. Lubrication required is minimal.
The jaw adapter plates are drilled to accept engraving block attachments. offers a 30-piece attachment set (#003-520) that includes storage for the adapter plates and pins that come with the block.

Maintenance

Based on usage, open jaws fully and clean any dirt and metal pieces from the threads. After cleaning, apply a small amount of light oil to the threads.

Vise Jaw Thread Replacement #003-627 & #003-628
Overtightening the jaws will cause wear and damage to the threads.
If jaws become loose, replace with kit #003-627. Remove the jaws by opening them as wide as possible until they come off the end of the jaw screw (FIG. 1). The jaw thread pin is located on the under side of each jaw.

NOTE: Before removing pins, locate the one with the “L”. This is the left hand thread pin and will need to replaced with the same. Apply a small amount of grease (included in kit) to the O-rings and jaw screw before installing them. Lift the jaw screw out of the yoke that it rotates in and replace it. Note which side the left hand thread is on. Grease the threads and yoke well.

Now, the hard part: you must start the jaws threads at the same time when replacing them (FIG. 2). Hold each jaw in position and turn the jaw screw to close them. Either a large rubber band or a second person is useful to help turn the jaw screw while you hold the jaws against the thread. If the jaws don’t meet at the same time in the center, remove them and try starting the threads at the same time again.

Rotational Lock Replacement
The LOCK or DRAG PIN is subject to much wear and may need to be replaced after extended use. Simply remove the ball swivel tension screw with the hex wrench. The spring and Lock Pin should follow (FIG. 3); if not, turn the ball until they fall out. Replace the Lock Pin (#003-046), Spring, and Tension Screw.

Turntable Base For Microscope Work · #003-616-V2
To use the Turntable Base, lock the vise by tightening the swivel tension screw until the ball will not turn. The turntable now becomes your rotation, allowing you to adjust the work’s center of rotation into the field of view of the microscope. Align the center of the turntable with the center of the microscope view (FIG. 4). Change working views by repositioning the vise.

Thread Pin Replacement Kit · #003-627
(Not Shown). Includes Jaw Screw, Left and Right Thread Pins, O-Rings, and Tube of Grease.

INSTRUCTION

With a variety of pins that fit the upper jaw plates of every block, users can now instantly solve work holding problems and start working sooner. Including 8 small pins,4 flat square pins,2 rectangular inset-curve pins, 4 thick round inset pins,8 rubber-coated pins, and 2 leather-faced ring clamp pins in molded base.

PART # DESCRIPTION/QTY.

1. Ring clamp assembly : 2
2. Attachment plate #3 assembly: 2
3. Attachment plate #2 assembly: 4
4. A t tachment plate #1 assembly: 4
5. Attachment pin #3 assembly (short): 4
6. Attachment pin #2 assembly (long) : 4
7. Formed complete attachment pin #1: 8

contact

• Manufacturer: Jiaxing Taishi Machinery & Equipment Co., Ltd
• Address: Room 402, Fazhang building, No.159 Qinjian Road, Jiaxing City, Zhejiang Province, China
• Tel: +86 057382826352

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>