Olarm PRO Multi Network Communicator Installation Guide

June 5, 2024
Olarm

Olarm PRO Multi Network Communicator logo

Olarm PRO Multi Network Communicator

Olarm PRO Multi Network Communicator product Locate your Nemtek electric fence energizer
Olarm PRO Multi Network Communicator 01

  • Druid 13LCD & 15LCD
    Olarm PRO Multi Network Communicator 02

  • Druid 18LCD
    Olarm PRO Multi Network Communicator 03

  • Druid 25LCD & 28LCD
    Coming soon
    Olarm PRO Multi Network Communicator 04

  • Merlin M4i
    Olarm PRO Multi Network Communicator 05

  • Merlin Stealth M18S & M28X

Unbox your Olarm PRO
The Olarm PRO box includes the following:

  • 1x Olarm PRO device
  • 1x Connector cable
  • 1x Drill hole template and LED colour legend
  •  2x Screws and wall plugs
    Olarm PRO Multi Network Communicator 06

Download the Olarm mobile app & register your device
Scan the QR code (left), or navigate to your App store on your device and search for ‘Olarm’. This Olarm PRO will require an active subscription to function. Please contact your installer or speak to sales@olarm.co for more information.
Olarm PRO Multi Network Communicator 07

  • Druid

  • Merlin 4
    Olarm PRO Multi Network Communicator 09

  • Merlin Stealth

Druid: You will be prompted to enter your Master PIN and Reset PIN. These are by default 1234 and 5555 respectively. Please contact the Nemtek installer should these not work.
Merlin: You will be prompted to enter your Master PIN and User PIN. These are by default 1234 and 5555 respectively. Please contact the Nemtek installer should these not work.
Power down the electric fence energizer
Disconnect both the mains and battery power from the electric fence energizer before continuing.
Connect your Olarm PRO device to your electric fence energizer
Connect the 4-pin connector to the Universal port on the Olarm PRO. Cut the 5-pin plug off the cable and strip the wires so you can insert them. Wire the Olarm PRO into the key bus according to the diagram below.
Olarm PRO Multi Network Communicator 10 Note:
The Druid only supports two keypads & Olarm PRO counts as Keypad #2. You may therefore need to forfeit a keypad if you already have two connected.
Turn the Nemtek electric fence energizer back on
Check your Olarm PRO’s status.

Olarm PRO Multi Network Communicator 11| White| Booting up
---|---|---
Olarm PRO Multi Network Communicator 12| Flashing green| Connecting to energizer
Olarm PRO Multi Network Communicator 13| Flashing blue| Connecting to cloud
Olarm PRO Multi Network Communicator 14| Blue| Connected, all okay
Olarm PRO Multi Network Communicator 15| Red| Cannot connect to energizer
Olarm PRO Multi Network Communicator 16| Orange| Cannot connect to cloud
| Yellow| WiFi pairing active
Olarm PRO Multi Network Communicator 17| Purple|

Firmware upgrading – do not power the device off

Mount the Olarm PRO
Mount your device using the screws and drill template provided. We suggest mounting the Olarm PRO device on a wall as far from the Nemtek energizer as convenient.
Note:

  •  Please do NOT mount the Olarm PRO near any other radio equipment. They may interfere with each other and result in your device not functioning correctly.
  • The Olarm PRO device is not weather resistant, and you will need to install it in a suitable non-metal enclosure if outdoors.

Connect to WiFi
Please follow the in-app guide to connect your Olarm PRO to WiFi for enhanced connectivity.

Note:
The Olarm PRO only supports 2.4GHz WiFi.
Note:

  • Please note that the Olarm PRO acts as a keypad when installed on a Nemtek energizer and will automatically cycle through the zones to read each zone’s status on multi-zone energizers’. Any key press on the keypad will stop the zone cycling. The Olarm PRO will commence zone cycling after not detecting a key press for 30 seconds.
  • Olarm PRO with batch number starting with 2022 onward are compatible.

Troubleshooting

  • If your device LED remains flashing green for more than 3 minutes – please check the connection between the Olarm PRO and the electric fence energizer.
  • If your device LED is red – please check the connection between the Olarm PRO and the electric fence energizer.
  • If your device LED is orange – please ensure that the Olarm PRO is located in an area with good mobile signal strength. If it is not, please ensure that your device is connected to WiFi using the wizard inside the Olarm App.
  • If your device LED is not coming on – please check the connection between the Olarm PRO and the electric fence energizer and that the electric fence energizer is connected to power.
  • If your device LED remains purple for more than 15 minutes – please contact Olarm Support: +27 21 009 0911 or support@olarm.co.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals