Shark Lift-Away Pro S3973 Series Steam Pocket Mop User Manual

Shark Lift-Away Pro S3973 Series Steam Pocket Mop User Manual

QUICK START GUIDE

WHAT’S INSIDE

A. Steam Mop Handle
B Steam Mop Body
C. Removable Handheld Steamer
D. Intelli-Mop™ Head
E. Dirt Grip™ Pad (x2)
F. Filling Flask
G. Accessory Hose
H. Garment Steamer
I. Small Above-Floor Pocket Tool and Pad

ASSEMBLY

1. Screw the mop handle into the Steam Mop body (screwdriver not included)
2. Slide the Intelli-Mop Head post into the Steam Mop body. Push until you hear it click securely into place.

FILLING THE WATER TANK

1. Open the water tank cap.
2. Use the filling flask and pour water into the tank Do not overfill. Replace the cap on the water tank.

TOUCH-FREE TECHNOLOGY

1. Lift the mop straight up by the handle until the Intelli-Mop Head is hanging straight down. Center the mop head above the pad. Press down the release buttons on the sides of the head post, and both sides of the mop head will drop open.

2. Slip the mop head’s 4 corner tabs into the 4 corner pockets of the Dirt Grip™ Pad.

3. Gently press the Intelli-Mop Head to the floor on one side of the pad, and that side will click into place.

4. Flip the other side of the Intelli-Mop Head over onto the floor to click into place.

REMOVING THE PAD

Lift the mop straight up by the handle until the Intelli-Mop Head is hang- ing straight down. Press down the release buttons on the sides of the head post, and both sides of the mop head will drop open.

CAUTION: It is recommended that you allow the pads to cool off before removing them from the accessories to avoid possible scalding injury.

STEAM BLASTER™ TECHNOLOGY

When you need an extra burst of steam to clean tough, dried messes and stuck-on stains, use the Steam Blaster.
1. Flip back the Intelli-Mop™ Head so that it is behind the mop body.
2. Tilt the mop handle back. This will cause the Steam Blaster to emit a concentrated blast of steam onto the floor.
3. To stop the Steam Blaster spray, simply tilt the mop handle forward.
4. Flip the Intelli-Mop Head back into its original position and continue cleaning.

CLEANING

1. Plug the power cord into an outlet. The STEAM CONTROL button will flash blue.
2. Press the STEAM COTROL button to select your steam setting: once for LO, twice for HI, and three times to place the unit in STANDBY MODE.

INTELLIGENT STEAM CONTROL®

ABOVE-FLOOR CLEANING

Remove the Handheld Steamer by pressing the release button and pulling it away from the cradle.

Snap the desired accessory into the main nozzle of the Handheld Steamer. Then squeeze the steam trigger to activate steam.

Once done with handheld steaming, press the STEAM CONTROL button until the light flashes blue to put the unit in STANDBY MODE. Let cool for 2 to 3 minutes before removing mop head, pads, or handheld accessories and storing.
(Note: Tools mode is only available when using the Handheld Steamer. When the Handheld Steamer is removed from the cradle, it will automatically go into Tools mode.)

ABOVE-FLOOR CLEANING ACCESSORIES

For questions or to register your product, contact us at: 800-798-7398 or visit us online at sharkclean.com

Note: Please be sure to read the enclosed Owner’s Guide prior to using your unit.

FAQs

This article contains the FAQs for the S3973 Series Shark® Lift-Away® Pro Steam Pocket® Mop. This supports the following product SKUs S3973, S3973D, and S3973WM.

Can I use or add a cleaning solution to the water tank or apply to the pads?

Shark Steam Mops are designed to deliver effective, chemical-free cleaning and sanitization with just ordinary tap water. Using any type of cleaning solution, perfumed oils or other chemical cleaner with your steam mop is not recommended. These products can have damaging effects to your steam mop and defeat the benefit of chemical-free cleaning. Do not use anything other than water in the unit. Shark recommends using distilled water in your steam mop.

Can I use the steam mop on all floor surfaces?

The steam mop is designed for use on most hard floor surfaces. We recommend that you first test an isolated area of the floor surface to be cleaned as well as review the use and care instructions from your floor manufacturer.

Surfaces/Material where the steam mop should not be used:
1. Wax polished furniture or floors.
2. Unsealed or unglazed ceramic floors, unsealed wooden and wax floors and some no wax floors.
3. In cases of surfaces treated with wax and some no-wax floors, the sheen may be removed by heat or steam action of the unit. Test an isolated are of flooring first to see if sheen is affected.

Steam mops are ideal for: Laminate, Bamboo, Hardwood, Marble, Tile, Stone

How do I wash the pads?

Wash the pads with liquid detergent (not powder), as powder can leave a residue behind on the pad. Avoid use of bleach and fabric softeners when washing pads. Line dry, or dry on a low dryer setting. For best pad performance, we recommend replacing pads every 2-3 months if pads are used and washed 3 or more times/week. You can order replacement pads at www.sharkclean.com

How do I turn on my steam mop?

Once you have put water in the tank, plug the power cord into a 120V electrical outlet. The ON/STANDBY button will flash blue. Press the ON/STANDBY Button until the desired steam setting is selected. Press the ON/STANDBY once to select the Dust steam setting, press twice to select the Mop steam setting, and press the button three times to select the Scrub steam setting.

How long will it take my steam mop to heat up?

The steam mop is ready to clean in about 30 seconds.

What is variable steam, and how should it be used to achieve the best results?

The Shark Pro Steam Pocket Mop has three unique steam settings, so you can use the perfect amount of steam for the cleaning task at hand.
Setting: Dust
– Ideal for these surfaces: Laminate, Bamboo, Hardwood and Marble
– Recommended usage: Light cleaning & dusting, Loosen & lift dirt, Sanitize floors
Setting: Mop
– Ideal for these surfaces: Hardwood, Marble, Tile and Stone
– Recommended usage: Everyday cleaning, Remove spots and routine messes, Moderate cleaning of heavily trafficked areas and Sanitize floors.
Setting: Scrub
– Ideal for these surfaces: Hardwood (not recommended for continuous cleaning), Tile, Stone, Linoleum and Carpet (with the glider attachment)
– Recommended usage: Tough cleaning and removal of stuck-on messes and stains, Deep cleaning of heavily trafficked areas, Cut through heavy dirt and grime, Sanitize floors and Freshen area rugs and carpets.

Why should the pads be washed prior to use?

It is important to wash the pads, in order to remove any loose lint or fibers from the pad that might have occurred in packaging or in transport. Pads should be washed with liquid detergent (not powder), as powder can leave a residue behind. Avoid bleach and fabric softeners as well. Dry pads on a low dryer setting or line dry.

How long will the pads last?

Frequency of use, the type of cleaning (heavy/light) and how often the pads are washed and dried all determine the life of the pads and when new pads are required. Under normal household conditions, using the mop for routine cleaning a few times per week, we recommend new pads every 2-3 months.

What is the best use for the Steam Concentrator Nozzle?

The Steam Concentrator Nozzle will help loosen debris from crevices and tight areas that are tough to clean. For best results, use the Scrub steam setting and spray steam directly onto the dirty area. Once the Nozzle is cool, remove and attach the Mop Head to wipe away the loosened debris. Alternatively, you may use cloth or paper towels to wipe the area.

How and when should I use the Carpet Glider?

The Carpet Glider should be used with the all-purpose head to groom and freshen your carpet and area rugs by lightly applying steam to the carpet or rug fibers.
To use, attach the Mop Head and place on the Carpet Glider attachment. Press the ON/STANDBY button three times to select the Scrub Steam Setting. When your mop is ready, steam carpets with a back-and-forth motion.

Cleaning Tips

– Always sweep or vacuum floors prior to use to remove all loose dirt and debris from the floor surface.
– Wash pads prior to first use to remove any loose lint that may have occurred in packaging or transport.
– Select the appropriate steam setting for your cleaning needs: Use the Dust Setting for quick dusting, Use the Mop Setting for normal everyday steam cleaning, and use the Scrub setting for heavy cleaning (this will leave floors damp), and for use with Carpet Glider.
– Steam your floors with a forward and backward motion.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>