Gude GGH 35 TRI Hot Air Gas Turbine Instruction Manual
- June 3, 2024
- Gude
Table of Contents
Gude GGH 35 TRI Hot Air Gas Turbine
Introduction
Please read thoroughly this operation manual and attached safety instructions to enjoy your new gas hot air turbine. We further recommend to retain the operation manual for future references. We reserve right to make technical changes for the purpose of improvement in the course of continuous product development.
This is the original operation manual.
Device description (figure A+B)
- Gas hot air turbine with stainless steel housing
- Gas controller
- Gas hose connector
- ON/OFF switch – heating/fan
- Indicator
- Reset button
- Gas hose with connectors
- Pressure reducing valve
- Hose breaking protection
- Thermostat
- Digital room temperature indicator (actual value)
- Digital required temperature indicator (required value)
- Front cover
- Handle
Technical data
GGH 35 TRI
- Voltage/frequency: 230 V~50 Hz
- Heating output: 22-35 kW/18.900-30.000 kcal.per hour (controllable)
- Consumption: 2.0-2.5 kg per hour
- Operating pressure: 1500 mbar
- Fan output: 707 m³ per hour
- Gas type: Propane-butane
- Feeder cable length: 1.6 m
- Weight: 7.8 kg
Use as designated
The gas hot air turbine has exclusively been designed for heating and drying out purposes in the building industry (fabrics), agriculture, storage spaces (ventilated rooms only), etc.
The appliance may only be used as designated. The manufacturer cannot be held
liable for any damage if provisions of the generally applicable regulations
or provisions of these Operating Instructions are not followed.
General safety instructions
Read and observe all instructions contained herein before commissioning and
operation of the device.
Keep the safety instructions for future reference!
Safe work
Keep your workplace tidy!
Disorder on workplace may result in injuries.
Consider surrounding conditions!
Do not expose to rain.
Do not use in moist or wet environment.
Provide good lighting.
Do not use close to flammable liquids or gases (except for substances required for operation – here propane/butane).
Keep other persons in a safe distance!
Other persons, particularly children, may not touch the device and power
cable. Keep them in a sufficient distance from your workplace.
Store your device properly!
The device, if not used, should be stored in a dry and closed space, out of
reach of children.
Do not overload your device!
You will work better and more safely if the device is used at performance
power for which it is designed to.
Use correct device!
Do not use the device for purposes other than intended.
Secure your device correctly!
Connect your device according to instructions in
“Assembly” section.
Take care of your tools!
Observe maintenance directions and instructions.
Check tool cable regularly and ask an authorized specialist to replace the
same if damaged.
Check extension cable regularly and replace, if damaged. Keep handles dry,
without traces of oils and greases.
Be careful!
Be aware of what you are doing. Approach your work with sound mind. Do not use
the device if you are tired.
Check the device for damage!
Before use, check thoroughly all safeguards and slightly damaged parts if they
are still functioning properly.
Check whether rotary parts operate freely and not jammed or damaged.
All parts must be installed properly and must comply with conditions so that
perfect operation of the device is ensured.
Damaged safeguards and parts must be either repaired or replaced by an
authorized workshop, unless specified otherwise in this operation manual.
Replace damaged switches in a service workshop. Do not use the devices with
malfunctioning ON/OFF switch.
WARNING!
Use of non-compliant accessories may result in an injury.
Have your device repaired by an electrician only!
This device complies to applicable safety provisions. Repairs may be performed
by an electrician with the use of genuine spare parts, otherwise the user may
be exposed to injury hazard.
Safety instructions specific for this device
- This device may be used outside only and in well ventilated areas, however, it must be protected against moisture or rain.
- Gas cylinder must be always protected against freeze and minus temperature at any times.
- The device may be used for heating only.
- Attention! Open flame tightness test is strictly prohibited.
- Do not operate under ground level.
- Do not move and lift the device if in use.
- Radiation area must be at least 3 meters from persons and all flammable substances.
- Keep 50 cm distance between walls and rear or sides of the device.
- If gas leaks (smell), close the gas cylinder valve immediately and keep the device out of reach of all flammable sources.
- Check tightness of all connections.
- Before putting the appliance into operation, all screwed connections must be checked if tight, using lye soap or leak detection spray!(pic. F+G)
- If gas leakage remains, call an expert before re-commissioning.
- Assembly and maintenance of the device must comply with laws and directives of a country where the device is used.
- Do never turn the gas cylinder upside down even though you think it is empty! This procedure may jam the hose with residues from the gas cylinder and cause fire hazard and immediate damage of the device.
- Do not disassemble the protective grid and/or other parts of the heater.
- Keep children out of reach of the burner.
- Do not operate the device without supervision!
- Do not cover the device!
- Do not use for drying of clothes etc.!
- Do not touch the protective grid and thermal shield, otherwise burning injury may occur!
- A dangerous lack of oxygen may be experienced in small spaces!
Identification
Product safety:
CE: The product complies with relevant EU standards
Prohibitions:
- No flame and no smoking
- Not cover
- No operation in closed spaces!
**Warning:**
- Caution! Dangerous electric voltage!
- Warning of fire hazardous materials
- Caution! Hot surface!
- Warning of gas bottles
- Caution! Dangerous electric voltage!
- Use outside only, however, protect against rain.
General prohibition sign
Read operation manual before use
Environment protection:
| **** | **** |
|---|---|
| Dispose waste not to harm your environment. | Packaging material from |
cardboard can be recycled in a collection point.
|
Defective and/or disposed electric or electronic devices must be delivered to
relevant collection points.|
Packaging:
|
---|---
Protect against moisture| Packaging must direct upwards
|
Interferon-Recycling|
Technical data
EU DECLARATION ON CONFORMITY
The company
Güde GmbH & Co. KG
Birkichstraße 6
D-74549 Wolpertshausen
hereby declares that the design and structure of the devices listed below and
in designs marketed conforms to applicable basic requirements of the EU
directives on safety and hygiene.
This declaration on conformity becomes void in case of a change to the device
not consulted with us.
Identification of the devices: GHH 35 TRI
Order No.: #85032
Applicable EU directives:
2009/142/ EG
Harmonized standards used
EN 1596:1998+A1:2004
DIN 4815-2(01.06.1979) (gas pipe)
EN 13785:2005+A1:2008(regulator)
Date/signature of manufacturer: 2012-07-04
Information about signer: the executive Mr Arnol d
Technical documentation: J. Bürkle FBL; QS
Warranty
The warranty exclusively applies to material or manufacturing defects. The original proof of purchase including the date of purchase must be submitted when applying a claim in the warranty period. The warranty does not cover any unauthorized use such as machine overload, violent use, damage by any other person or an undesirable item. The failure to follow the Operating Instructions and assembly instructions and common wear and tear are also excluded from the warranty.
Behaviour in case of emergency
Provide necessary first aid treatment corresponding to the injury nature and
seek qualified medical help as soon as possible.
Protect the injured person from other injuries and calm him/her down.
In case of accident, first aid kit must always be available in the place of
your work in accordance with DIN 13164. Material taken out of the first aid
kit needs to be supplemented right away.
Please provide the following details
if help is needed:
- Place of accident
- Accident nature
- Number of injured persons
- Injury type
The warranty applies exclusively on material or production defects. For warranty claims, please submit an original proof of purchase with date of purchase indicated. The warranty does not cover unprofessional use, such as overloading, violent use, damage caused by third party or a thing. The warranty also does not cover failure to comply with the operation manual and normal wear and tear.
Residual risks and protective measures
Electrical residual risks:
-
Direct electric contact:
May lead to electric shock.
To be used in electrical network with a safety switch against stray current only. -
Indirect electric contact:
May lead to electric shock.
To be used in electrical network with a safety switch against stray current only.
Thermal residual risks:
- Burns, chilblains:
A contact with the protection grid and appliance body may lead to burns. Avoid such structural parts.
Disposal
Disposal instructions are illustrated in the form of pictograms on the device or packaging. Description of the pictograms is given in “Identification” chapter.
Disposal of transport packaging
Packaging protects the device against damage during transport. Packaging
materials are usually selected according to their effect on environment and
disposal methods and can therefore be recycled.
Returning of the packaging back to circulation saves resources and costs for
packaging disposal.
Parts of the packaging (e.g. foil, striper) may be dangerous for children.
Risk of suffocation!
Keep these parts of the packaging out of reach of children and dispose as soon
as possible.
Operator requirements
The operators must thoroughly read operation manual before use.
Qualification
Except for thorough training by an expert for use of the device, no special
qualification is required.
Minimum age
The device may be operated by persons over 16 years of age. An exception is
use by younger person if the use takes place under supervision of an adult
trainer in the course of education.
Training
Use of the device requires corresponding guidance by an expert or operation manual only. No special training is required.
Application according to intended use
Attention!
DO NOT USE FOR HEATING OF RESIDENTIAL SPACES IN RESIDENTIAL BUILDINGS;
NATIONAL PROVISIONS MUST BE OBEYED IN CASE OF USE IN PUBLIC BUILDINGS.
The gas heater must not be used:
- For heating of closed or residential spaces (residential buildings) or operation in such spaces;
- Close to flammable materials (e.g. paper, construction materials);
- On places where volatile materials are stored/present (e.g. gasoline, solvents, chemicals) or where explosive atmosphere may be generated;
- Following unauthorized structural change to the gas heater;
- In case of incorrect or unacceptable connection to gas source;
- On places insufficiently ventilated;
- As source of heating during social events and family celebrations.
Instructions for installation and putting the appliance into operation (pic. B-K)
Appliance to be used on a level, stable and non-flammable surface. Never use the appliance near open fire or flying sparks or similar high-flammable substances!
-
The appliance may only be used with propane or butane.
-
Connect the gas hot air turbine as specified in pic. B-F.
-
All connectors to be checked for gas detection using lye soap or leak detection spray. (pic. F+G)
-
Plug the appliance (pic. G)
-
Position “I”. The gas hot air turbine only runs with the fan function and provides air circulation in the room. (pic. I)
-
Position “II”. The gas hot air turbine is now also heating (pic. J). However, the appliance is only started when the required temperature (pic. K/12) is set higher than the actual temperature (pic. K/11) (room temperature).
-
Electronic control: Pic. K/11 shows the room temperature. Use the thermostat (pic. K/8) to control/set the required temperature – see the indicator (pic. K/12).(The gas hot air turbine is automatically switched on and then switched off when the required temperature is reached).
Example of use:
“II” (pic. J) 15°C actual temperature (pic. K/11)
20° temperature required (pic. K/12).
The gas hot air turbine is now able to heat the “space” to 20°C and then is automatically switched off. If the appliance remains in the emergency position, the gas hot air turbine is automatically switched on when it is below the required temperature. -
If the controller (pic. K/8) is set below the actual room temperature shown on the digital indicator (K11), the appliance also gets switched off.
Example of use: 18°C actual temperature (pic. K/11) 15°C temperature required (pic. K/12). The gas hot air turbine now gets switched off. If the appliance remains in the emergency position, the gas hot air turbine is automatically switched on when it is below 15°C.
The indicator (K/4) lights up in case of failure or when the gas bottle is
empty.
Press Reset (pic. K/6) and put ON/OFF to “0” or change the gas bottle and
connect it as specified in pic. B+F. The gas hot air turbine can now be
switched on again as specified.
Switching off (pic. L-M))
To switch the gas hot air turbine off, close the gas bottle valve (pic. L)
first at all times.
Switch the appliance off by ON/OFF (pic. M). To the position “0”.
To unplug the appliance, disconnect the plug (pic. M).
Changing the gas bottle
- When outdoors and in a safe distance from any fire or flammable sources and with no persons around proceed as follows!
- Close the gas bottle valve. (E/1)
- Unscrew the pressure reducing valve (pic. B-D in the reverse order).
- Make sure pressure reducing valve gasket is in place.
- Connect the appliance to a new gas bottle and proceed as specified in pic. B-H).
Transport, storing and cleaning
The appliance may only be carried using the carrying handle.
Appliances not being used must be kept in a dry and locked room.
- To clean the appliance, use a smooth and fine soap water solution. Prevent any direct contact of aggressive cleaning agents with the appliance. No aggressive, volatile or caustic cleaning agents may be used.
- Have the gas hot air turbine checked by a qualified authorized expert once a year.
- The hose must necessarily be replaced if damaged.
- The appliance needs to be protected against moisture and dust.
- If the appliance has not been used for a long time, disconnect it from the gas bottle and keep it covered in a dry and safe place inaccessible to children.
Service
Any technical questions? Complaint? Do you need spare parts or operation
manual?
Go to our website www.guede.com and the section
Service will help you quickly and without bureaucracy. Please, help us to help
you. In order to identify your device in case of complaint, please indicate
serial number, order number and year of manufacture. All information is
available on the product label. To have all information always at hand, put
them down.
Serial number:
Order number:
Year of manufacture:
Phone: +49 (0) 79 04 / 700-360
Fax: +49 (0) 79 04 / 700-51999
E-Mail: support@ts.guede.com
Troubleshooting
| Defect | Cause | Remedy |
|---|---|---|
| Electric motor does not start | No current | Check plug |
Check power supply connection
Piezo-ignition does not ignite| Electrode in incorrect position| Call
specialist
No gas| Gas cylinder empty| Replace gas cylinder.
Close valve on the gas cylinder| Open valve.
Gas hose or leaking connection| Seek for leaking point by suitable spray and
remove
Burner ignites, flame goes off as soon as the gas valve is turned on| Thermal
element not yet hot properly.| Try again
Safety thermostat turned off| Let the device cool down and then retry
Burner flame goes off during operation| Excessive gas output| Have the
reduction valve checked or replaced
Gas cylinder empty| Replace gas cylinder.
Insufficient gas input| Check and clean motor grid
Check fan
Wind or air draught extinguishes flame.| Place the device outside wind or air
draught, let it cool down for several minutes and then retry
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>