PIZZELLO Caldo Fire Pit Table Instruction Manual

PIZZELLO Caldo Fire Pit Table

Product Information

Specifications:

• Burner: 1PC
• Glass Fire Stone: 1PC
• Plastic Foot: 4PCS
• *Stainless steel screw M512:** 2PCS
• *M530:** 6PCS
• *M48:** 4PCS
• *M512:** 28PCS

Product Usage Instructions

Step 1: Assembly
Follow the provided assembly instructions to put together the components of the Pizzello Caldo. Make sure to use the correct screws and parts as indicated in the manual.

Step 2: Ignition
Before igniting the unit for the first time, follow these steps:

1. Ensure all assembly steps are completed correctly.
2. Insert a 1.5V battery (not included) as per the instructions.
3. Set the ignition switch to the desired heat level (LOW, MEDIUM, HIGH).

Step 3: Cooking
Place the Pizzello Caldo on a stable surface and ignite the burner following the provided instructions. Once lit, you can start cooking your pizza on the glass firestone. Monitor the cooking process as needed.

Frequently Asked Questions (FAQ):

• Q: What type of battery is needed for ignition?
  A: A 1.5V battery is required for ignition, which is not included in the product.

• Q: How many plastic feet come with the product?
  A: The product comes with 4 plastic feet to ensure stability when in use.

Attention

1. We are concerned about each customer’s experience, if there is any missing or damage, please contact us at any time, and we will provide effective solutions. We also have the assembled video on the product details page to help you install this fire pit table.
2. Come with multiple boxes, please check if you already received all the boxes we shipped to you. Sometimes these boxes will not arrive on the same date, hope you can wait for 2-3 more days or contact us for more help. If you already have the all boxes, please kindly send us messages to let us know the name of the missing part regarding the first page of instructions. We will send a replacement to you ASAP.
3. If there is any damage, please send clear photos of the damaged part to us as an attachment, and we will check and offer you the best solution soon.
4. This fire pit table needs a 1 AAA 1.5V battery to ignite. (Note: The battery is Not included.）

DANGER:
FIRE OR EXPLOSION HAZARD

If you smell gas:

• Shut off the gas to the appliance.
• Extinguish any open flame.
• If the odour continues, leave the area immediately.
• After leaving the area, call your gas supplier or fire department.

Failure to follow these instructions could result in fire or explosion, which could cause property damage, personal injury, or death.

WARNING:

• Do not store or use gasoline, or other flammable vapors and liquids, in the vicinity of this or any other appliance.
• An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.

WARNING: For Outdoor Use Only.
Installation and service must be performed by a qualified installer, service agency, or gas supplier.

DANGER
CARBON MONOXIDE HAZARD

• This appliance can produce carbon monoxide which has no odour.

• Using it in an enclosed space can kill you.

• Never use this appliance in an enclosed space such as a camper, tent, car or home.

• INSTALLER: Leave this guide with the appliance.

• CONSUMER: Retain this manual for future reference.

• WARNING:
  If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.

• WARNING:
  Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment.

LP SAFETY

• Do not store a spare LP gas cylinder under or near this appliance.
• Never fill the cylinder beyond 80 per cent full.
• If the information in “(a)” and “(b)” is not followed exactly, a fire causing death or serious injury may occur.

MINIMUM CLEARANCES:

• Bottom: Non-Combustible Surface
• Top: 60 inches
• Sides: 36 inches
• For Installation on (or over) non-combustible floors only
• Max. Input: 50,000 BTU/h
• Max. Gas Supply Pressure: 250 PSI
• Min. Gas Supply Pressure: 25 PSI

Do not use this appliance under overhead combustible surfaces.

• This appliance shall be used only outdoors in a well-ventilated space and shall not be used in a building, garage or any other enclosed area.
• If this appliance is not in use, the gas must be turned off at the supply cylinder.
• Indoor storage of this appliance is permissible only if the cylinder is disconnected and removed from the appliance.
• Cylinders must be stored outdoors in a well-ventilated area out of the reach of children.
• Disconnected cylinders must have threaded valve plugs tightly installed and must not be stored in a building, garage or any other enclosed area.
• The gas pressure regulator provided with this appliance must be used and must be the same model as that supplied with the unit.
• The cylinder supply system must be arranged for vapour withdrawal.
• Cylinders used with this unit must have a collar to protect the cylinder valve.
• An approved LP cylinder stabilizer, such as the stabilizer ring included, must be used when the appliance is in use.

LP CYLINDER:
All LP cylinders to be used with this appliance must be:

• Constructed and marked under the specifications for LP-gas cylinders Standard, CAN/CSA B339, Cylinders, Spheres and Tubes for the Transportation of Dangerous Goods.
• Provided with a listed overfilling prevention device.
• Provided with a cylinder connection device compatible with the connection for outdoor cooking appliances.
• Only a 20 lb (9 kg) LP gas cylinder is to be used for this appliance, approximately 18″ (46 cm) high & 12″ (30 cm) diameter.

WARNING:

• Please ensure that all adults and children who use or are near a unit in use are aware of the hazard of high surface temperatures present on the unit during use and should use caution and stay away to avoid burns or clothing ignition.
• Carefully supervise young children in the area of this appliance.
• Clothing or other flammable materials should not be hung from the appliance or placed on or near the appliance. Any guard or other protective device removed for servicing the appliance must be replaced before operating the appliance.
• Installation and repair should be done by a qualified service person.
• The appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required as necessary. Control compartments, burners and circulating air passageways of the appliance must be kept clean.

ENCLOSURES FOR SELF-CONTAINED LP GAS SYSTEMS

An enclosure for an LP gas cylinder shall be ventilated by openings at both the upper and lower levels of the enclosure. This shall be accompanied by one of the following:

• One side of the enclosure shall be completely open; or
• For an enclosure having four sides, a top, and a bottom:

At least two ventilation openings shall be provided in the sidewalls of the enclosure, located within 5 in (217 mm) of the top of the enclosure, equally sized, spaced at a minimum of 90 degrees (1.57 rad), and unobstructed. The opening(s) shall have a total free area of not less than 1 in2 per lb (14.2 cm2 per kg) of stored fuel capacity.

Ventilation opening(s) shall be provided at the floor level of the enclosure and shall have a total free area of not less than 1/2 in2 per lb (7.1 cm2 per kg) of stored fuel capacity. If ventilation openings at the floor level area are in the side wall, there shall be at least two openings. The bottom of the openings shall be 1 in (25.4 mm) or less from the floor level and the upper edge no more than 5 in (127 mm) above the floor level. The openings shall be equally sized, spaced at a minimum of 90 degrees (1.57 rad), and unobstructed. Every opening shall have minimum dimensions to permit the entrance of a 1/8 in (3.2 mm) diameter rod. Ventilation openings in sidewalls shall not communicate directly with other enclosures of the appliance.

CONNECTION AND DISCONNECTION

1. Be sure the cylinder valve and appliance valves are “off”.
2. Place full LP gas cylinder on tank stabilizer ring. Secure the base of the LP gas cylinder by hand tightening the wing-nut collar.
3. Centre the nipple in the cylinder valve and hold it in place.
4. Using the other hand, turn the hand wheel clockwise until there is a positive stop. Do not use tools.
5. Hand tighten only. When making the connection, hold the regulator in a straight line with the cylinder valve, so as not to cross-thread the connection.
6. Leak test the connection.

DISCONNECTION:

1. Be sure the cylinder valve and appliance valves are “off’ before disconnection.
2. Using one hand, turn the hand wheel anticlockwise.

LEAK TEST

1. DO NOT USE OR PERMIT SOURCES OF IGNITION IN THE AREA WHILE DOING THE LEAK TEST. THIS INCLUDES SMOKING.
2. Leak testing should be done once per year or whenever the LP gas cylinder or any other gas system part is taken apart, serviced or replaced, whichever is more frequent.
3. Ensure all gas system coupling joints are tight and properly attached.
4. Prepare a leak-testing solution of half liquid detergent and half water.
5. Apply the solution to the LP gas delivery system at points as shown in the illustration.
6. The leak(s) must be stopped by tightening the loose joints, if possible, or by replacing the faulty parts(s) with the part(s) recommended by the appliance manufacturer.

WARNING:
If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Installation and service must be performed by a qualified installer, service agency or gas supplier.

THE APPLIANCE IS NOT TO BE USED UNTIL ANY LEAK IS CORRECTED.

• A gas appliance repairman or LP gas dealer should be called if attempts to stop the leak(s) are unsuccessful and, in such case, the LP gas supply must be shut off at the cylinder valve or the cylinder must be removed from the appliance until the leak(s) is corrected.
• Inspect the hose before each use of the unit. To gain access for inspection remove the side panels. To remove each side panel, simply use pull rings and lift the panel away. Refer to assembly instructions for visual diagrams. The hose assembly must be replaced before the appliance is put into operation if there is evidence of excessive abrasion or wear, or if the hose is damaged. Contact our customer service should you require a replacement hose. R replacement hose assembly shall be the one that is specified by the manufacturer.
• Inspect the burner before each use. The burner must be replaced before the appliance is put into operation if there is evidence of damage. Contact our customer service should you require a replacement burner.
• Should any part of this appliance (including the burner) become soiled or dirty, wipe lightly with a damp cloth. Do not use flammable or corrosive cleaning products on or near this unit.
• Ensure that the gas hose is placed in an area where it is unlikely to be tripped over (such as pathways or trails) or subject to other accidental damage.
• Keep the appliance area clear and free from combustible materials, gasoline and other flammable vapours and liquids.
• Solid fuels shall not be burned in this appliance.
• The installation must conform with local codes, or in the absence of local codes with the National Fuel Gas Code, ANSI Z223.l·NFPA 54; National Fuel Gas Code; Natural Gas and Propane Installation Code, CSA B149.1; or Propane Storage and Handling Code, CSA B149.2, as applicable.

Parts List

Box_A Parts List

Box_B Parts List

NOTE:
Please do not tighten all the screws until step 4.

Assembly Instructions

Step 1
Connect the part 1 to the tabletop (part 6) with 2 PCS screws F and 2 PCS washers G.

Step 2
Connect part 2 to the tabletop (part 6) with 2 PCS screws F and 2 PCS washers G.

Step 3
Connect part 5 to part 1 and part 2 with 8 PCS screw F.

Step 4
Connect the two parts 8 to part 1 and part 2 with 8 PCS screw F.

Step 5
Assemble the wheel H to part 4.

Step 6
Connect part 3 to part 4 with 2PCS screw D.

Step 7
Stretch the glide track, assemble the LEFT track and the part 2 with 2 PCS screw E. Assemble the RIGHT track and the part 1 with 2 PCS screw E.

Step 8
Connect the glid track to part 4 with 4 PCS screw D.

Step 9
Assemble the 4 pcs plastic adjustable feet B.

Step 10
Assemble the screw A to part 4.

Step 11
Connect Part 10 to Part 3 and Track 9 with 4 PCS screw F.

Step 12
Turn the table over, and the tabletop is facing up. Assemble the control panel with 4 PCS screws F.

Please make sure the heat shield under the burner is placed toward the door. If the installation direction is wrong, the thermocouple may break and the switch box may be upside down. Please install it strictly according to the directions indicated.

Step 13
Put the fire glass stone Y into the burner, and close the lid 7.

Note:
Glass Rocks shall be arranged neatly and evenly in the burner tray. Ensure the igniter cover is not covered by glass rocks (see photo). This helps air circulate. Take care to keep rocks out of the igniter cover. Keep the igniter clean of dust. For best flame results adjust the rocks to expose the burner tube holes. Our preferred configuration is pictured here.

WARNING:
Never handle glass rocks that have not been allowed to cool from exposure to flame. Never attempt to rearrange rocks while the unit is ignited.

• NOTE: Rocks are not to exceed 5 kg or 15.5 lb.
• NOTE: Never use a lid or cover to extinguish the flame on your Fire Table.

WARNING:
Avoid glass dust. Always wear gloves to handle rocks; be cautious of glass dust when handling; use a rag to wipe glass dust. Glass dust may result during shipping.

NOTE TO USER:
Before igniting the unit for the first time, follow steps one through 5 in the below Ignition section 1AAA 1.5V battery is needed（NOT included)

IGNITION

• STEP 1
  Ensure that the unit valve dial is in the “OFF” position by pushing and turning clockwise until the dial stops.

• STEP 2
  Connect the LP gas cylinder. See the section labelled “Connection”.

• STEP 3
  Ensure the gas hose is not contacting the top of the Fire Table enclosure and the tank is stabilized in the collar with the wing nut.
  Caution: Always ensure the gas valve orifice and burner tube venturi are clear of all debris including spider webs.

• STEP4

  • SLOWLY turn the cylinder valve to the open position to avoid tripping the excess flow safety device in the gas regulator.
  • For more information about the excess flow safety device see Section 3 (page 16).

• STEP 5
  Leak Test all connections. See the section labelled “Leak Test”.

• STEP 6

  • Your Fire Table is equipped with an auto spark ignition (piezo ignition). Push the knob in and slowly turn counter-clockwise to the high position. The igniter will spark and ignite the gas.
  • Should the appliance fail to ignite on the first try, promptly repeat the ignition attempt within 5 seconds. If a third attempt fails to ignite the Fire Table then rotate the knob to the “off” position and wait 5 minutes before attempting to ignite again.
    WARNING:
    Ensure that no parts of your body, clothing, or any other combustible material are above the burner before, during and after ignition. Ensure the cover is stored safely away from the Fire Table when the Fire Table is in use.

• STEP 7
  Once the unit is burning normally, set the dial to the desired flame height.

• STEP 8 PERIODIC INSPECTION OF BURNER FLAMES

  • Upon igniting the appliance, visually verify that the burner is indeed burning as demonstrated in the image. The presence of flames will confirm that the burner is burning. Periodically check that the burner flame is present during operation by visually
  • If there are no flames present, as demonstrated in the image, the appliance is likely not burning. If this is the case, IMMEDIATELY turn the valve to the “off” position if it is not already and repeat the ignition procedure as outlined in Section 2.

Normally the burner flame is yellow.
If the burner flame is blue and very small, please check the gas cylinder, as it may be low gas pressure or empty. If there is enough gas in the cylinder, please contact customer service to change the burner of the gas fire pit.

If flames lift away from the burner or backfire happens, or produces thick black smoke, the fire pit should be turned off immediately. The fire pit should not be operated again until the unit is serviced and/or repaired by a qualified service technician.

WARNING:
Improper lighting procedures may cause fire explosion, and result in property damage, personal injury, or loss of life.

FIRE TABLE WON’T LIGHT? IGNITION PROBLEM?
IGNITION TROUBLESHOOTING

• STEP 1
  Wait 5 minutes for any gas to dissipate. Locate the igniter cable under the table. Ensure the igniter cable is firmly attached to the gas valve. Follow the ignition sequence again. If still no results after three tries move to step 2 below.

• STEP 2
  Turn the gas cylinder valve to the “Closed” position. Wait 5 minutes for any gas to dissipate. Ensure the igniter cover is not covered by glass rocks. This helps air circulate. Inspect the ignition electrode (under the igniter cover) to ensure it is free from dust and not blocked by glass rocks or other debris. Use a dry clean cloth or tissue to very lightly wipe clean the igniter tip.

WARNING HAZARD:
USE A TOOL OR WEAR GLOVES TO MOVE GLASS ROCKS. AVOID BLOWING GLASS DUST IN THE AIR.

After waiting for 5 minutes, visually inspect the spark by rotating the knob to high without turning the gas back on at the cylinder. Ensure the spark gap is 3 – 5mm (1/8″ – 3/16″) from the burner port and has a clear path. Once you ensure the igniter is operating properly repeat the ignition sequence in section 2.

GOT A LOW FLAME

• STEP 1
  • Check propane level. If less than half full replace the cylinder.
  • Repeat the ignition sequence in section 2.
• STEP 2
  If the propane cylinder is full and your Fire Table experiences low flame, or flame height does not appear to be normally adjusted by the gas knob, the excess flow safety device has likely been tripped in the hose regulator.

CORRECTIVE ACTION

• Close the propane cylinder valve.
• Open and then close the Fire Table gas knob valve to release pressure.
• Disconnect and reconnect the propane cylinder valve connection.
• Slowly open the propane cylinder valve.
• Perform the Leak Test and follow the Ignition sequence.

EXTINGUISHING THE APPLIANCE

• STEP 1
  Access the Fire Table interior. Turn the gas cylinder valve to the “Closed” position.

• STEP 2
  Turn the gas knob on the Fire Table to the “OFF” position by pushing and turning the knob clockwise.

• STEP 3
  Allow the unit to cool for at least five (5) minutes before relighting.

FIRE TABLE MAINTENANCE

Your Fire Table requires periodic maintenance to keep it in good running order. Follow the steps below to ensure your appliance will provide you with the best possible performance:

1. Keep your Fire Table out of the rain and store it in a dry place. Fire table accessories such as covers can be purchased at our store or you can contact our customer service team.
2. This device has been engineered to provide the maximum amount of heat and comfort. If you experience any signs of your propane cylinder “freezing off” or start to experience lower flames than usual, please simply turn the burner control setting to low for 5-10 minutes, or replace the cylinder with a full one.
3. Ensure that you clean the top of your Fire Table after every use to keep it looking GREAT. Simply use warm soap water to wipe down your Fire Table to keep it clean. Do not use abrasive cleaners. Especially, DO NOT USE PETROLEUM-BASED SOLVENTS TO CLEAN YOUR FIRE TABLE AS THIS WILL DESTROY YOUR WICKER RESIN TABLE MATERIAL.
4. Remove any debris and leaves that may have accumulated in your Fire Table burner tray before igniting.

WARNING NOTES

• Expected burn time; the anticipated burn time for your Fire Table using a full 20 lb (9kg) propane cylinder is between 12 and 18 hours depending on where the flame height is set.
• This is NOT a toy.
• The fire table will become extremely hot during operation! – DO NOT TOUCH THE
• BURNER TRAY OR GLASS ROCKS while the fire table is in operation!
• Do not place ANY cover on the fire table while the fire table is in operation.
• Do not rest anything on or over the burner tray while the fire table is in operation.
• The fire table is a decorative gas appliance only. NEVER cook food on the fire table. Do not use any type of accessory as a means to cook or keep food warm on the fire table.
• Wait at least 30 minutes after turning off the fire table to allow it to cool down before touching the burner glassless rocks, or putting ANY cover over the fire table.
• Please ensure that all adults and children who use or are near a unit in use are aware of the hazard of high-surface temperatures present on the unit during use and should use caution and stay away to avoid burns or clothing ignition.
• Children should be supervised at all times when using this unit without exception.
• Do not place any objects other than supplied rocks inside the burner component of the Fire Table.
• Do not add wood or any other materials to the fire.
• Your Fire Table is designed to safely combust propane only.
• Do not connect to a remote gas supply. Consult a certified gas technician.
• Do not use this appliance if any part has been underwater. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control that has been under water.
• Do not leave this appliance uncovered in the rain.
• Always inspect and clear all valve and gas orifices of any foreign debris including spider webs before lighting.
• Never store a spare LP cylinder inside the LP cylinder compartment.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>