LLIVEKIT AF-D5508ATB Series 9L Digital Air Fryer User Manual
- June 1, 2024
- LLIVEKIT
Table of Contents
USER MANUAL
Model: AF-D5508ATB
S2-M-A00594
AF-D5508ATB Series 9L Digital Air Fryer
FOR HOUSEHOLD USE ONLY
Please read this manual carefully before use and save it for future reference.
Save These Instructions
This appliance is intended for household use only but not for situations similar to the following:
- staff kitchen areas in shops, offices and other working environments;
- farm houses;
- by clients in hotels, motels and other residential type environments;
- bed and breakfast type environments.
Important Safeguards
When using the appliance, basic safety precautions should always be followed, including but not limited to the following:
-
Do not immerse the main body in water or rinse under the tap due to the electronic and heating elements.
-
Avoid any liquid entering the appliance to prevent electric shock or short-circuit.
-
Keep all food ingredients in the frying pot to avoid any contact with the heating elements.
-
Do not cover the air inlet or outlet while in operation.
-
Do not fill the frying pot with oil, as it may cause a fire hazard.
-
Do not touch the inside of the appliance while in operation.
-
Check if the voltage indicated on the appliance fits the local mains voltage.
-
Never let the power cord hang over the edge of a counter table or touch hot surfaces.
-
Keep the appliance and its power cord out of reach of children.
-
Do not place the appliance on or near combustible materials such as a tablecloth or curtain.
-
Do not place the appliance against a wall or other appliances. Leave at least 10cm of free space around the appliance.
-
Do not place anything on the top of the appliance.
-
Do not use the appliance for any other purpose than described in this manual.
-
During operation, hot steam is released through the air outlet openings.
Keep your hands and face at a safe distance from the steam and from the air outlet openings. -
Be careful of hot steam and air when you remove the frying pot from the appliance.
-
If you see dark smoke coming out of the appliance, immediately unplug the appliance and wait for the smoke emission to stop before you remove the frying pot from the appliance.
-
Ensure the appliance is placed on a horizontal, even and stable surface.
-
The use of accessories not recommended by the appliance manufacturer may cause injuries.
-
Always unplug the appliance when not in use.
-
The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instructions concerning use of the appliance by a person responsible for their safety.
-
If the supply cord is damaged, contact our customer service.
-
Young children should be supervised to ensure that they do not play with the appliance.
-
The appliance is not intended to be operated by means of an external timer or a separate remote-control system.
-
Do not use the appliance outdoors.
-
Let the appliance cool down for approximately 30 minutes before handling or cleaning.
-
Remove any burnt residue.
-
If the appliance is used improperly or if it is not used according to the instructions in the user manual, the seller refuses any liability for any damage that may cause.
Introduction
This air fryer provides an easy and healthy way to prepare your favorite foods. With rapid hot air circulation and top heating elements, it can cook a wide variety of dishes. Best of all, the air fryer heats ingredients in all directions and most ingredients require no oil.
Specifications
- Rated voltage: 220-240V~50Hz
- Rated power: 2700 (1350+1350) Watts
- Capacity of pot: 9.0L
- Temperature range: 80-200°C
- Timer: 1-60min
Appliance Overview (Fig. 1)
- Top Cover
- Upper Shell
- Control Panel
- Frying Grill
- Frying Pot
- Pot Front
- Viewing Window
- Pot Handle
- Divider
- Air Outlet (right)
- Lower Shell
- Base
- Power Cord
- Air Outlet (left)
Warnings
-
Do not use the appliance for any other purpose than described in this manual.
-
Do not let the appliance operate unattended.
-
During hot air frying, hot steam is released through the air outlet openings.
Keep your hands and face at a safe distance from the steam and from the air outlet openings. Also, be careful of hot steam and air when you remove the pot from the appliance. -
Any accessible surfaces may become hot during use (Fig. 2).
-
Immediately unplug the appliance if you see dark smoke coming out of the appliance. Wait for the smoke emission to stop before you remove the pot from the appliance.
Before First Use
- Remove all packaging materials.
- Remove any stickers or labels from the appliance.
- Thoroughly clean the frying grills and pot with hot water, some washing-up liquid and a non-abrasive sponge.
- Wipe inside and outside of the appliance with a damp cloth.
This is an oil-free air fryer that works on hot air. Do not fill the pot with oil or frying fat directly.
Notice: When the appliance is heated for the first time, it may emit slight smoke or odour. This is normal with many heating appliances and does not affect the safety of your appliance.
Preparing for Use
- Place the appliance on a stable, horizontal and even surface.
Do not place the appliance on non-heat-resistant surface.
Using The Appliance
The oil-free air fryer can prepare a large range of ingredients.
Hot Air Frying
-
Connect the mains plug into an earthed wall socket (Fig. 3).
-
Pull the pot out of the appliance (Fig. 4).
-
Place the frying grills in the pot (Fig. 5).
Do not fill the pot with oil or any other liquid.
Do not put anything on top of the appliance, as the airflow will be disrupted to affect the hot air frying result. -
Put the ingredients in the pot (Fig. 6).
-
Push the pot back into the appliance (Fig. 7).
Carefully align with the guides inside the appliance.
Never use the pot without the frying grill in it.
Caution: Do not touch the pot during and just after use, as It gets very hot. Only hold the pot by the handles. -
Determine the required preparation time for the ingredients (see Settings).
-
Some ingredients require shaking halfway through cooking (see Settings).
To shake the ingredients, pull the pot out of the appliance with the handles and shake it, then push the pot back into the appliance. -
When you hear a beep sound, the set preparation time has ended. Pull the pot out of the appliance.
Note: Press and hold the power button for 2 seconds, then you can switch off the appliance manually.
Tip: You can adjust the cooking temperature or time according to your taste during use. Your settings will be stored for about 60 minutes after you pull the pot out of the appliance. -
Check if the ingredients are ready. If the ingredients are not ready yet, simply push the pot back into the appliance and set the timer for a few extra minutes.
-
To remove ingredients (e.g. fries), pull the pot out of the appliance and place it on a heat-resistant surface.
Do not turn the frying pot upside down, as any excess oil that has been collected on the bottom of the pot will leak onto the ingredients.
Extreme care that the pot and the ingredients are hot during and just after cooking. Depending on the type of ingredients In the appliance, steam may escape from the pot. -
Use tongs or other tools to transfer food to a plate.
-
When a batch of ingredients is ready, the appliance is instantly ready for preparing another batch.
Operation Instructions
The display is divided into two halves. The left and right halves of the display respectively show the settings for the zone on their sides. The icons and near are used to adjust the temperature and time for the left zone while the ones and near are used for the right zone.
-
Boot Mode
Put the frying pot inside the appliance correctly and power on, you can hear a beep sound at this time and see all indicators illuminating on and off in 1 second, except the always-on and the appliance enters into the Boot Mode. Once the appliance is powered on, is always on. -
Standby Mode
Press , and illuminate. By now, the appliance enters Standby Mode. If there is no further operation within 5 minutes, it will return to Boot Mode. -
Single Zone Working Mode
3.1. Press or , the function buttons, preset icons and the corresponding display illuminate, the default preset icon of steak flashes, and the other preset icons are always on. The temperature and the time on the display flash.
3.2. Select the desired preset and you can decide to adjust the temperature and time according to the food you are going to cook. When adjusting the temperature, press and to adjust by 5°C per time, if press and hold either of them, the value will be increased or decreased continuously within the range of 80-200°C. When adjusting the time, press and to adjust by 1min per time, if press and hold either of them, the value will be increased or decreased continuously within the range of 1-60min.
Note: You should press or first and start to adjust the temperature or time setting till the display reads the temperature or time. Or, wait to adjust till you see the temperature or time is displayed naturally.
3.3. After selecting the preset and adjusting the cooking temperature and time, press to start cooking in Zone or . By now, the display reads the needed time for the preset and it no longer flashes, the selected preset icon is always on and the others go out. The smart finish button =! doesn’t illuminate but the other function buttons are always on.
3.4. If it’s required to adjust the cooking temperature or time during cooking, press or , press or to adjust when the display reads the temperature or time, during which the heating tubes and the motors keep working.
3.5. If it’s required to change the preset during cooking, press to stop cooking. By now, the heating tubes stop working and the motors work for another 20 seconds then stop working, the selected preset icon, the indicator to the selected zone and the power button indicator flash, you can select the desired preset at this time, as well as adjust the cooking temperature and time.
3.6. When working, press the appliance stops working. If there’s no further operation in 5 minutes, it will return to Standby Mode.
3.7. If it’s required to switch off the appliance during cooking, press and hold for 2 seconds, the heating tubes stop working and the motors work for another 20 seconds then stop working. By now, the display reads “OFF”. After you hear a beep sound, the display goes out and the appliance returns to Standby Mode.
3.8. After the cooking process ends, the display reads “OFF” and you will hear 5 beeps, then the display goes out and the appliance returns to Standby Mode.
3.9. Pull out the frying pot during cooking, the left and right displays read “OPEN” and both zones stop working. After pushing back the frying pot, the appliance resumes the previous cooking process. -
Dual Zone Working Mode
4.1. To Cook in the Dual Zone
4.1.1. Select one zone first and select the desired preset, adjust to the desired cooking temperature and time, then do the same operation for the other zone.
4.1.2. Then press to start cooking in dual zone, both two halves of the display read the cooking time, the selected preset icon for Zone and start to flash every 6 seconds. In 3 seconds, the selected preset icon for Zone and start to flash every 6 seconds. The left and right sides flash alternately with an interval of 3 seconds.
4.1.3. Also you can press to start cooking in Zone after you finish all the settings for Zone , then press to start the settings for Zone , and press to start cooking in Zone .
4.1.4. When both zones are working, press and two halves of display read the cooking temperature for the selected presets, and then they automatically read the cooking time in 3 seconds. Or, press and two halves of display read the cooking time for the selected presets.
4.2. To Adjust Settings in Dual Zone
4.2.1. When both zones are working, if it’s required to adjust the cooking temperature or time for Zone ①, press and start to adjust as desired. At this time, the preset cannot be changed. If there is no further operation in 10 seconds after settings, the display automatically returns to normal display. 4.2.2. If it’s required to adjust the cooking temperature or time for Zone ②, refer to 4.2.1.
4.2.3. During cooking, press or and it flashes, then press to pause cooking in Zone ① or ②. By now, you can change the preset, adjust the cooking temperature and time, then press to resume cooking.
4.2.4. After pausing the cooking process, if there is no further operation in 5 minutes, the paused zone will enter Standby Mode.
4.3. To switch off Zone ① or ②, press or and press and hold for 2 seconds, the selected zone stops working and returns to Standby Mode.
4.4. To Pull Out Frying Pot.
4.4.1. Pull out the frying pot during cooking, the corresponding heating tubes and the motors of Zone ① and ② stop working, the corresponding half of the display reads “OPEN”. As long as the appliance is powered on, Zone ① and ② resume the previous cooking process after the frying pot is put back.
4.4.2. In Standby Mode, the two halves of the display read “OPEN” after pulling out the frying pot. By now, the control panel cannot be operated.
4.5. To Pause Working in Dual Zone
4.5.1. Press during cooking, both zones pause cooking. By now, the selected preset icons on the two halves of the display flash as well , and . Press one more time, both zones resume the previous cooking process.
4.5.2. After both zones are paused, the appliance will stop working and return to Standby Mode if there is no further operation in 5 minutes.
4.5.3. Press during cooking, both zones pause cooking. At this time, if it’s required to change the preset or adjust the cooking temperature or time, press or to change or adjust. After the setting is done, press one more time, both zones the previous cooking process.
4.5.4. Press during cooking, both zones pause cooking. By now, press and hold for 2 seconds to stop cooking, the two halves of the display read “OFF”, you can hear a beep sound and the appliance returns to Standby Mode.
4.6. To Finish Cooking in Dual Zone.
4.6.1. If there is no any operation when the dual zone is cooking, after the cooking time ends, the heating tubes stop working and the motors work for another 20 seconds then stop working, the two halves of the display read “OFF”, you can hear 5 beeps, the display goes out and the appliance returns to Standby Mode.
4.6.2. If it’s required to switch off one zone when the dual zone is cooking, press or first and then press and hold for 2 seconds to switch off the selected zone, the corresponding display now reads “OFF”, you can hear a beep sound and the appliance returns to Standby Mode. At this time, only one zone is working.
4.7. To Finish Together
4.7.1. When both zones are working, the smart finish button illuminates to flash and you can decide to activate this function.
4.7.2. After the settings for the dual zone are done, press and then press , the smart finish icon stops flashing to be always on. Press one more time and the appliance starts cooking. At this time, the zone set with the preset that needs longer time starts cooking first, and the display of the other one that needs shorter time reads “Hold” and it starts cooking till the one that needs longer time has the same remaining time, thus both zones can be ready at the same time. During this process, is always on.
4.7.3. When both zones are working together, if one zone is working and the other is being held, a. if the zone being held is set with longer cooking time than the working one, or if the working zone is set with shorter cooking time than the one being held,
the smart finish process will be stopped, will go out.
b. pull out the frying pot, the 2 halves of the display read “OPEN”, the time is paused, the heating tubes and the motors stop working. Put the frying pot back, the appliance resumes the previous cooking process.
c. pause the zone that is working, the smart finish process stops, goes out and the other zone starts to work.
d. pause the zone that is being held, the smart finish process stops, goes out and the other zone continues to work.
4.7.4. When both zones are working together, if the dual zone is set with the same time settings, pull out the frying pot and push in again, the time is synchronised and the smart finish function is still activated.
4.7.5. When both zones are working together, pause the working process, the smart finish process stops and flashes.
4.7.6. When both zones are working together, press to stop the smart finish process and goes out.
5.1. Preheat Function: In Standby Mode, press and in a sequence, then press to start preheating for Zone ①. By now, and flash every 2 seconds; press and in a sequence, then press to start preheating for Zone ②. By now , and flash every 2 seconds.
5.2. In Standby Mode, press and , then and in a sequence, press in the end. By now , , and together flash every 2 seconds and the preheating on dual zone starts.
Control Panel
-
Boot Mode: only always on.
-
Standby Mode: , and always on.
-
When selecting and adjusting before cooking: the corresponding function button is always on, the selected preset icon flashes while the others are always on, and the temperature/time flashes on the corresponding display.
At this time, you can change the preset and adjust the cooking temperature and time. -
When selecting and adjusting during cooking: the preset icons do not flash, but the temperature and time on the display flash. You can adjust the cooking temperature and time, but the preset cannot be changed.
-
When one zone is paused working: the corresponding function button is always on, the selected preset icon flashes while the others are always on, the temperature/time flashes on the corresponding display as well and . At this time, you can change the preset and adjust the cooking temperature and time.
-
When both zones are paused working: the corresponding function button is always on, the selected preset icon flashes while the others are always on, the temperature/time flashes on the corresponding display as well as and .
-
Working Mode: The selected function button is always on, as well as the selected preset icon, but not the other preset icons. The corresponding display reads the preparation time.
-
When both zones are working together, the selected preset icon for Zone ① and flash every 6 seconds, and the time it takes to go out is less than 0.5 seconds. In 3 seconds, the selected preset icon for Zone ② and start to flash every 6 seconds, and the time it takes to go out is less than 0.5 seconds. The left and right sides flash alternately with an interval of 3 seconds.
-
Memory Function: The appliance has a memory function. When the cooking is finished and the appliance is not powered off, when selecting the same zone as the last time for the next use, it will directly display the menu used last time. The memory function fails when the appliance is powered off for 1 hour. It will display the initial state when it is powered on again after more than 1 hour power-off.
-
Power-off Memory Function: If there is an accidental power failure while the appliance is in use, the appliance will return to the working status before power failure as long as it is re-powered on within 30 minutes.
-
Error Display
11.1 E1 displayed: NTC open circuit
11.2 E2 displayed: NTC short circuit
Settings
The table below will help you to select the basic settings for the
ingredients.
Note: Keep in mind that these settings are only for reference. As
ingredients differ in origin, size, shape as well as brand, we cannot
guarantee the best settings for your ingredients.
The Rapid Air Technology instantly reheats the air inside the appliance, so
pulling the pot briefly out of the appliance during hot air frying barely
affects the cooking.
Tips
- Smaller ingredients usually require a slightly shorter preparation time than larger ingredients.
- A larger amount of ingredients only requires a slightly longer preparation time, and vice versa.
- Shaking smaller ingredients halfway through cooking optimises the result and can help prevent unevenly fried ingredients.
- Add some oil to fresh potatoes for a crispy result. Fry the ingredients in the appliance within a few minutes after you add the oil.
- Snacks that can be prepared in an oven can also be prepared in the appliance.
- The optimal amount for preparing crispy fries is 500 grams.
- Use a pre-made dough to prepare filled snacks quickly and easily. A pre-made dough also requires a shorter preparation time than a home-made dough.
- Place a baking tin or oven dish in the appliance if you want to bake a cake or quiche or to fry fragile ingredients or filled ingredients.
- You can also use the appliance to reheat the ingredients. To reheat ingredients, set the temperature to 150°C for up to 10 minutes.
Menu| Reference Weight (grams)| Default Temperature (°C)| Default Time (min)|
Temperature Range (°C)| Time Range (min)| Shaking required (times)
---|---|---|---|---|---|---
| 400| 200| 15| 80-200| 1-60| 1-2
| 600| 200| 30| 80-200| 1-60| 1-2
| 600| 190| 10| 80-200| 1-60| 1-2
| 500| 180| 25| 80-200| 1-60| 1-2
| 400| 180| 10| 80-200| 1-60| —
| 450| 200| 25| 80-200| 1-60| 1-2
---|---|---|---|---|---|---
| 400| 180| 12| 80-200| 1-60| —
| 300| 170| 20| 80-200| 1-60| 1-2
Note 1 : Add 3 minutes to the preparation time when you start frying
while the appliance is still cold.
Note 2 : You can adjust the cooking temperature or time according to the
actual cooking performance when using dual cooking zones at the same time.
Cleaning
Clean the appliance after every use.
The frying pot and the frying grills have a non-stick coating. Do not use
metal kitchen utensils or abrasive cleaning materials to clean them, as this
may damage the non-stick coating.
-
Remove the mains plug from the wall socket and let the appliance cool down.
Note: Remove the pot to let the appliance cool down more quickly. -
Wipe the outside of the appliance with a damp cloth.
-
Clean the pot and grills with hot water, some washing-up liquid and a non-abrasive sponge. You can use washing-up liquid to remove any remaining dirt.
Tip: If any dirt is stuck to the frying grills or the bottom of the pot, fill the pot with hot water and with some washing-up liquid. Put the frying grills in the pot and let them soak for approximately 10 minutes. -
Clean the inside of the appliance with hot water and non-abrasive sponge.
-
Clean the heating elements with a cleaning brush to remove any food residues.
Storage
- Unplug the appliance and let it cool down.
- Make sure all parts are clean and dry.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| **** The appliance does not work. | Unplugged. | Connect the mains plug into an |
earthed wall socket.
You have not set the timer.| Set the required preparation time and
switch on the appliance.
The ingredients fried by the appliance are not fully cooked.| The amount
of ingredients in the pot is too big.| Put smaller batches of ingredients in
the pot. Smaller batches are fried more evenly.
The set temperature is too low.| Set the required temperature (see
Settings).
The preparation time is too short.| Set the required preparation time
(see Settings).
The ingredients are fried unevenly.| The certain types of
ingredients need to be shaken halfway through cooking.| The ingredients that
lie on the top of or overlaps with others (e.g. fries) need to be shaken
halfway through cooking (see Settings).
The fried snacks are not crispy.
| You used a type of snack meant to be prepared in a traditional deep fryer.|
Use oven snacks or lightly brush some oil onto the snacks for a crispier
result.
The pot cannot be pushed into the appliance properly.| There are too
many ingredients in the pot.| Do not fill beyond the MAX indication.
The pot is not placed correctly.| Put the pot in until you hear a
click.
The white smoke comes out of the appliance.| You are preparing
greasy ingredients.| When you fry greasy ingredients, a large amount of oil
will leak into the pot. The oil produces white smoke and the pot may heat up
more than usual. This does not affect the appliance or the cooking result.
The pot still contains grease residues from the previous use.| The white
smoke is caused by grease heating up in the pot. Make sure you clean the pot
properly after each use.
The fresh fries are fried unevenly.| You did not use the right
type of potato.| Use fresh potatoes and make sure they stay firm during
frying.
---|---|---
You did not rinse the potato strips properly before you fried them.|
Rinse the potato strips properly to remove starch from the outside of the
strips.
The fresh fries are not crispy.| The crispiness of the fries
depends on the amount of oil and water in the fries.| Make sure you dry the
potato strips properly before you add the oil.
Cut the potato strips smaller for a crispier result.
Add lightly more oil for a crispier result.
Disposal Considerations
To protect the environment and human health, the waste electrical and
electronic equipment should not be disposed of together with household waste.
Instead, it must be taken to a designated collection point for recycling of
your waste electrical and electronic equipment. For more information about the
recycling and disposal of this appliance, please contact your local authority
or your household waste disposal service.
V 2.02
Documents / Resources
|
LLIVEKIT AF-D5508ATB Series 9L Digital Air
Fryer
[pdf] User Manual
AF-D5508ATB Series 9L Digital Air Fryer, 9L Digital Air Fryer, Air Fryer
---|---