DYNOJET PC6-20042 Power Commander 6 Installation Guide

DYNOJET PC6-20042 Power Commander 6

PARTS LIST

• 1 POWER COMMANDER 6
• 1 INSTALLATION GUIDE
• 1 USB CABLE
• 2 DYNOJET DECALS
• 2 POWER COMMANDER DECALS
• 2 VELCRO STRIPS
• 1 ALCOHOL SWAB
  PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION.
  THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.

INPUT ACCESSORY GUIDE

PRODUCT OVERVIEW

OPTIONAL ACCESSORY INPUTS

• Map (Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You can switch on the fl y between these two base maps when you hook up a switch to the MAP inputs. You can use any open/close type switch. The polarity of the wires is not important.
• Shifter (Input 1 or 2) Used for clutch-less full throttle upshifts. Insert the wires from the Dynojet quick shifter into either Input 1 or Input 2. The polarity of the wires is not important. Set to Input 2 by default.
• Speed If your application has a speed sensor then you can tap into the signal side of the sensor and run a wire into this input. This will allow you to calculate gear position in the Control Center Software. Once gear position is setup you can alter your map based on gear position and setup gear dependent kill times when using a quick shifter.
• Analog This input is for a 0-5v signal such as engine temp, boost, etc. Once this input is established you can alter your fuel curve based on this input in the Power Core software.
• Launch You can connect a wire to either Input 1 or Input 2 and then the other end to a switch. This switch when engaged (continuity) will only allow the RPM to be raised to a certain limit (set in the software). When released, you will have full RPM.

WIRE CONNECTIONS
To input wires into the PC6 fi rst remove the rubber plug on the backside of the unit and loosen the screw for the corresponding input. Using a 22-24 gauge wire, strip about 10mm from its end. Push the wire into the hole of the PC6 until it stops and then tighten the screw. Make sure to reinstall the rubber plug.
NOTE: If you tin the wires with solder it will make inserting them easier.

INSTALLING THE POWER COMMANDER 6

1. Remove the main seat and the passenger seat.
2. Hold the front of the fuel tank up using the prop rod located in the trunk area.
3. Locate the connector from the main wiring harness to the injector rail and unplug this connector.
   Note: This connector is BLACK in color and may be covered by a rubber boot.

4. Plug the pair of connectors from the PC6 in-line of the stock connectors.

5. Route the PC6 wiring along the inside of the frame towards the battery.
6. Secure the ground wire of the PC6 to the negative (-) side of the battery.

7. Using the supplied Velcro, secure the PC6 module in the rear section of the trunk.
   Make sure to clean both surfaces with the supplied alcohol swab before attaching.

8. Bolt fuel tank back into place and reinstall the seats.

Download the latest map fi les from our web site at dynojet.com/tunes.

Optional inputs:

• Speed input – PINK wire on BLACK 3-pin connector from speed sensor on the countershaft sprocket cover (BLACK/RED, BLACK/WHITE, PINK).
• Temperature input – BLACK/BLUE wire of temp sensor at the rear of the engine.
• 12v for Autotune – Brown wire of tail light connector.

ABOUT COMPANY

• 2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081
• 800-992-4993
• DYNOJET.COM
• © 1999-2022 DYNOJET RESEARCH ALL RIGHTS RESERVED

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>