LIVEX 49996 Brushed Nickel Island Light Fixture Instruction Manual

LIVEX 49996 Brushed Nickel Island Light Fixture

Specifications

• Model Numbers: 49996, 49997, 49347, 49349
• Power Source: Junction Box
• Fixture Compatibility: Light bulbs (not included)
• Fixture Wires:
  • Black or Smooth
  • White or Ribbed
  • Bare Copper (Ground)
• House Wires:
  • Black (Hot)
  • White (Neutral)
  • Green or Bare Copper (Ground)

Product Usage Instructions

1. Shut off the power at the circuit breaker box and remove the old fixture and hardware from the Junction Box.
2. Unpack the new fixture and lay out all parts carefully in a clear area.
3. Determine the desired hanging height and slide the electrical wires through the tubes and canopy.
4. Raise the tubes and canopy onto the lamp body and secure them tightly.
5. Attach the mounting plate to the junction box, ensuring correct orientation.
6. Connect the electrical wires following the provided diagram, securing all wire nuts and using electrical tape as needed.
7. Secure the canopy to the junction box and lock it with the column nuts.
8. Ensure proper arm positioning and install light bulbs according to specifications without exceeding wattage limits.
9. Turn on the power to the junction box and test the fixture.

FAQ

• Q: What should I do if I have extra parts after assembling the fixture?
• A: Please double-check the assembly steps to ensure all parts are correctly installed. If you still have extra parts, contact customer service for assistance.
• Q: Can I use LED bulbs with this fixture?
• A: Yes, you can use LED bulbs as long as they are compatible with the fixture specifications and do not exceed the specified wattage.
• Q: How do I clean and maintain this fixture?
• A: To clean the fixture, switch off the power and allow it to cool. Use a soft, dry cloth to gently wipe the surface. Avoid using harsh chemicals or abrasive materials.

ASSEMBLING & INSTALLATION INSTRUCTIONS

• The drawing shown may not exactly match the product enclosed.
• However, the installation instructions do apply to this product.

WARNING! SHUT THE POWER OFF AT THE FUSE OR CIRCUIT BREAKER.
ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.

ASSEMBLING THE FIXTURE (Fig.1)

1. Shut off the power at the circuit breaker box. Remove old fixture and all hardware from Junction Box.

2. Carefully unpack your new fixture and lay out all the parts in a clear area.
   Take care not to lose any small parts necessary for installation.

3. Determine the desired hanging height. Slide the electrical wires through the tubes(F)/(E)/(D)/(C)/(B), double loop and canopy(A).

4. Raise the tubes and double loop to the pipe thread in the lamp body(G), then by turning it clockwise until tight. Raise the canopy(A) onto the end pipe thread of double loop, and secure it with the spring shim and hex nut until tight.

5. Thread the four mounting screws into the pre-drilled holes in the mounting plate spaced the same distance apart as the holes in the canopy(A). Attach the mounting plate to the junction box with the two junction box screws as shown. The side of the mounting plate marked “GND” must face out.

6. While holding the fixture lamp towards the ceiling, connect the electrical wires as Shown in Fig.2, making sure that all wire nuts are secured. You may have to wrap the connections with electrical tape. If your outlet has a ground wire (green or bare copper), connect the fixture ground wire to it. Otherwise, connect the fixture’s ground wire directly to the Mounting plate with the green screw provided. After the wires are connected, tuck them carefully inside the junction box.

7. Raise the canopy (A) onto the junction box, aligning screws on the mounting plate with mounting holes in the canopy and locking it securely with the column nuts.

8. WARNING: RETURN THE ARMS TO THE VERTICAL POSITION, THE END OF THE LAMP HOLDER MUST UPWARD. BUT DOES NOT A CONTINUOUS ROTATION OF AN ENTIRE ARM!

9. Install the light bulbs(Not included) under the fixture specifications. NOTE: DO NOT EXCEED THE SPECIFIED WATTAGE!

Your installation is now complete. Return power to the junction box and test the fixture.

Thank you for purchasing a LIVEX product.

CONTACT

• Need assistance with parts or assembly?
• Please call customer service at 800-761-8056 Or visit us online at: WWW.LIVEXLIGHTING.COM.

©COPYRIGHT ALL RIGHTS RESERVED.LIVEX LIGHTING,INC.

References

• Livex Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>