Pioneer SPH-DA77DAB RDS AV Receiver Instruction Manual

Pioneer SPH-DA77DAB RDS AV Receiver

Product Information

Specifications

• Model: SPH-DA77DAB
• Languages: Nederlands, Deutsch, Italiano, English
• GPS aerial length: 3.55 meters
• Microphone length: 3 meters
• Power supply fuse: 10 A
• Control signal output: max. 300 mA 12 V DC

Product Usage Instructions

Checking Supplied Items
Ensure all supplied items including connection cables, installation parts, GPS aerial, microphone, and other items are present.

Connection
Follow the provided connection instructions carefully to ensure proper installation.

Precautions
Before connecting the system, read and adhere to the important safeguards and precautions mentioned in the manual.

Checking supplied items

This product/connection cables/installation parts

• This product (×1)
• Power cord (×1)
• Pre out cord (×1)
• SWC/Back Camera cord (×1)
• AUX IN cord (×1)
• USB cable (×1)
• Holder (×1)
• Screw (×4)
• Trim ring (×1)
• Flush surface screw (×4)
• Side bracket (×2)
• Screw for fixing the side bracket (×2)

Connection

Precautions

Your new product and this manual

• Do not operate this product, any applications, or the rear view camera option (if purchased) if doing so will divert your attention in any way from the safe operation of your vehicle. Always observe safe driving rules and follow all existing traffic regulations. If you experience difficulty in operating this product, pull over, park your vehicle in a safe location and apply the handbrake before making the necessary adjustments.
• Do not install this product where it may

1. obstruct the driver’s vision,
2. impair the performance of any of the vehicle’s operating systems of safety features, including airbags, hazard lamp buttons, or
3. ) impair the driver’s ability to safely operate the vehicle.

GPS aerial/installation parts

• GPS aerial (×1)
• Double-sided tape (×1)
• Clamps (×3)

Microphone/installation parts

• Microphone (×1)
• Double-sided tape (×1)

Other items

• Manual(s) (×1)
• Warranty Card (×1)

In some cases, it may not be possible to install this product because of the vehicle type or the shape of the vehicle interior.

Important safeguards

WARNING
Pioneer does not recommend that you install this product yourself. This product is designed for professional installation only. We recommend that only authorised Pioneer service personnel, who have special training and experience in mobile electronics, set up and install this product. NEVER SERVICE THIS PRODUCT YOURSELF. Installing or servicing this product and its connecting cables may expose you to the risk of electric shock or other hazards, and can cause damage to this product that is not covered by warranty.

Precautions before connecting the system

WARNING
Do not take any steps to tamper with or disable the handbrake interlock system which is in place for your protection. Tampering with or disabling the handbrake interlock system could result in serious injury or death.

CAUTION

• Secure all wiring with cable clamps or electrical tape. Do not allow any bare wiring to remain exposed.
• Do not directly connect the yellow lead of this product to the vehicle battery. If the lead is directly connected to the battery, engine vibration may eventually cause the insulation to fail at the point where the wire passes from the passenger compartment into the engine compartment. If the yellow lead’s insulation tears as a result of contact with metal parts, short-circuiting can occur, resulting in considerable danger.
• It is extremely dangerous to allow cables to become wound around the steering column or gearstick. Be sure to install this product, its cables, and wiring away in such so that they will not obstruct or hinder driving.
• Make sure that the cables and wires will not interfere with or become caught in any of the vehicle’s moving parts, especially the steering wheel, gearstick, handbrake, sliding seat tracks, doors, or any of the vehicle’s controls.
• Do not route wires where they will be exposed to high temperatures. If the insulation heats up, wires may become damaged, resulting in a short circuit or malfunction and permanent damage to the product.
• Do not shorten any leads. If you do, the protection circuit (fuse holder, fuse resistor or filter, etc.) may fail to work properly.
• Never feed power to other electronic products by cutting the insulation of the power supply lead of this product and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating.

Before installing this product

• Use this product with a 12-volt battery and negative earthing only. Failure to do so may result in a fire or malfunction.
• To avoid shorts in the electrical system, be sure to disconnect the (–) battery cable before installation.

To prevent damage

WARNING

• When speaker output is used by 4 channels , use speakers over 50 W (Maximum input power) and between 4 Ω to 8 Ω (impedance value). Do not use 1 Ω to 3 Ω speakers for this unit.
• The black lead is earth. Please earth this lead separately from the earth of high current products such as power amps. Do not earth more than one product together with the earth from another product. For example, you must separately earth any amp unit away from the earth of this product. Connecting earths together can cause a fire and/or damage the products if their earths became detached.
• When replacing the fuse, be sure to only use a fuse of the rating prescribed on this product.
• This product cannot be installed in a vehicle without ACC (accessory) position on the ignition switch.
• To avoid short-circuiting, cover the disconnected lead with insulating tape. It is especially important to insulate all unused speaker leads, which if left uncovered may cause a short circuit.
• For connecting a power amp or other devices to this product, refer to the manual for the product to be connected. The graphical symbol placed on the product means direct current.

Notice for the blue/white lead

• When the ignition switch is turned on (ACC ON), a control signal is output through the blue/white lead. Connect to an external power amp’s system remote control terminal, the auto-aerial relay control terminal, or the aerial booster power control terminal (max. 300 mA 12 V DC). The control signal is output through the blue/white lead, even if the audio source is switched off.

This product

1. GPS aerial 3.55 m
2. Microphone 3 m
3. Connector 1 (REAR VIEW CAMERA IN/MUTE/STEERING WHEEL CONTROL)
4. This product
5. Digital Radio aerial input
6. Aerial jack
7. CANBUS
8. Connector 2 (AUX IN)
9. Pre out supply
10. Fuse (10 A)
11. Power supply
12. To connector 1
13. SWC/Back Camera cord
14. Wired remote input (STEERING WHEEL CONTROL)
15. Hard-wired remote control adapter can be connected (sold separately).
16. Brown (REAR VIEW CAMERA IN) Yellow/black (MUTE)
17. Not used

Power cord

1.  To power supply

2. Depending on the kind of vehicle, the function of 2 and 4 may be different. In this case, be sure to connect 1 to 4 and 3 to 2.

3. Yellow (2*)
   Back-up (or accessory)

4. Yellow (1*)
   Connect to the constant 12 V supply terminal.

5. Red (4*)
   Accessory (or back-up)

6. Red (3*)

7. Connect to terminal controlled by ignition switch (12 V DC).
   Connect leads of the same colour to each other.

8. Orange/white
   To lighting switch terminal.

9. Black (earth)
   To vehicle (metal) body.

10. Blue/white (5)
    The pin position of the ISO connector will differ depending on the type of vehicle. Connect 5 and 6 when Pin 5 is an aerial control type. In another type of vehicle, never connect 5 and 6. Blue/white (6)

11. Connect to auto-aerial relay control terminal (max. 300 mA 12 V DC). Blue/white

12. Connect to system control terminal of the power amp (max. 300 mA 12 V DC). Violet/white
    Of the two lead wires connected to the back lamp, connect the one in which the voltage changes when the gear shift is in the REVERSE (R) position. This connection enables the unit to sense whether the car is moving forwards or backwards.

13. Pink
    Car speed signal input

14. Light green

15. Used to detect the ON/OFF status of the handbrake. This lead must be connected to the power supply side of the handbrake switch.

16. If this connection is made incorrectly or omitted, certain functions of this product will be unusable. Connection method
    Clamp the lead (1) then clamp firmly with needle-nosed pliers (2).

17. Speaker leads

    • White: Front left +
    • White/black: Front left –
    • Grey: Front right +
    • Grey/black: Front right –
    • Green: Rear left +
    • Green/black: Rear left –
    • Violet: Rear right +
    • Violet/black: Rear right –

18. ISO connector
    In some vehicles, the ISO connector may be divided into two. In this case, be sure to connect to both connectors.

NOTES

• The position of the speed detection circuit and the position of the handbrake switch vary depending on the vehicle model. For details, consult your authorised Pioneer dealer or an installation professional.
• The position of the handbrake switch depends on the vehicle model. For details, consult the vehicle Owner’s Manual or dealer.

Power amp (sold separately)

Important
The speaker leads are not used when this connection is in use.

1.  Subwoofer output (SUBWOOFER OUT L/SUBWOOFER OUT R) RCA cable (sold separately)
2. Power amp
3. Front output (FRONT OUT L/FRONT OUT R)
4. Rear output (REAR OUT L/REAR OUT R) Yellow/black (MUTE)
5. If you use an equipment with Mute function, wire this lead to the Audio Mute lead on that equipment. If not, keep the Audio Mute lead free of any connections.
6. Pre out cord
7. To pre out supply
8. To connector 1
9. System remote control
10. Connect to Blue/white cable.
11. Rear speaker
12. Front speaker
13. Subwoofer

iPhone and smartphone

NOTES

• For details on how to connect an external device using a separately sold cable, refer to the manual for the cable.
• For details concerning the connection and operations of iPhone or smartphone, refer to the Operation Manual.
• iPhone and Lightning are trademarks of Apple Inc., registered in the U.S. and other countries and regions.

iPhone with Lightning connector

Connecting via the USB port

1.  iPhone with Lightning connector
2. USB interface cable for iPhone (sold separately)
3. USB cable 1.5 m
4. USB port

Smartphone (Android™ device)

Connecting via the USB port

1.  Smartphone
2. USB – micro USB cable (USB Type-A to micro USB Type-B) (sold separately) USB Type-C® cable (USB Type-A to USB Type-C) (sold separately)
3. USB cable 1.5 m
4. USB port

NOTES

• Due to the USB standard, the total length when a USB Type-A to micro USB Type-B cable (2 ) and a USB cable ( 3) are connected cannot exceed 2 m, and when a USB Type-A to USB Type-C cable (2 ) and a USB cable (3) are connected cannot exceed 4 m. If you use a cable other than the above conditions, the main unit function may not operate properly.
• Android is a trademark of Google LLC.
• USB Type-C® and USB-C® are registered trademarks of USB Implementers Forum.

Camera

About rear view camera
When you use the rear view camera, the rear view image is automatically switched from the video by moving the gearstick to REVERSE (R). Camera View mode also allows you to check what is behind you while driving.

WARNING

• USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE REAR VIEW CAMERA. OTHER USE MAY RESULT IN INJURY OR DAMAGE.
• THE SECOND CAMERA INPUT IS AVAILABLE TO SUPPLEMENT THE DRIVER’S VIEW BUT IS NOT A SUBSTITUTE FOR THE DRIVER’S CAREFUL ATTENTION, AND PIONEER ACCEPTS NO RESPONSIBILITY FOR LOSS OR DAMAGE IN CONNECTION WITH ITS USE. IT IS THE DRIVER’S RESPONSIBILITY TO BE AWARE OF SURROUNDINGS AND CONDITIONS AT ALL TIMES WHILE OPERATING A VEHICLE, INCLUDING CHECKING REARVIEW AND/OR SIDE MIRRORS AS NEEDED WHEN REVERSING.

CAUTION

• The screen image may appear reversed.
• With the rear view camera you can keep an eye on trailers, or back into a tight parking spot. Do not use for entertainment purposes.
• Objects in rear view may appear closer or more distant than in reality.
• The image area of full-screen images displayed while backing or checking the rear of the vehicle may differ slightly.

1.  This product

2. Pre out supply

3. Connector 1

4. Power supply

5. To connector 1

6. To power supply

7. To pre out supply

8. SWC/Back Camera cord

9. Power cord

10. Pre out cord

11. Brown (REAR VIEW CAMERA IN) Violet/white (REVERSE-GEAR SIGNAL INPUT)

12. Refer to Power cord on page 3.

13. Yellow (SECOND CAMERA INPUT)
    NOTE
    Do not use the second camera for any purpose other than driving assistance.

14. RCA power supply cable (sold separately)

15. To video output

16. Rear view camera (sold separately)

17. RCA cable (sold separately)

18. View camera (sold separately)

NOTES

Connect only the rear view camera to REAR VIEW CAMERA IN. Do not connect any other equipment.
Some appropriate settings are required to use rear view cameras. For details, refer to the Operation Manual.

External video component and the display

1.  This product
2. Pre out supply
3. Connector 2
4. To connector 2
5. To pre out supply
6. Pre out cord
7. Mini-jack AV cable (sold separately)
8. UX input (AUX IN)
9. AUX IN cord
10. Yellow (REAR MONITOR OUT)
11. Yellow
12. Red, white
13. RCA cables (sold separately)
14. To video input
15. Rear display with RCA input jacks
16. To video output
17. To audio outputs
18. External video component (sold separately)

WARNING
NEVER install the rear display in a location that enables the driver to watch the video source while driving.
This product’s rear video output is for connection of a display to enable passengers in the rear seats to watch the video source.

CAUTION
Be sure to use a mini-jack AV cable (sold separately) for wiring. If you use other cables, the wiring position might differ resulting in disturbed images and sounds.

• L : Left audio (White)
• R : Right audio (Red)
• V : Video (Yellow)
• G : Earth

Installation

Precautions before installation
CAUTION

• Never install this product in places where, or in a manner that:

  • Could injure the driver or passengers if the vehicle stops suddenly.
  • May interfere with the driver’s operation of the vehicle, such as on the floor in front of the driver’s seat, or close to the steering wheel or gearstick.

• To ensure proper installation, be sure to use the supplied parts in the manner specified. If any parts are not supplied with this product, use compatible parts in the manner specified after you have the part compatibility checked by your dealer. If parts other than supplied or compatible ones are used, they may damage internal parts of this product or they may work loose and the product may become detached.

• Do not install this product where it may
  (i) obstruct the driver’s vision, (ii) impair the performance of any of the vehicle’s operating systems or safety features, including airbags, hazard lamp buttons or (iii) impair the driver’s ability to safely operate the vehicle.

• Never install this product in front of or next to the place in the dashboard, door, or pillar from which one of your vehicle’s airbags would deploy. Please refer to your vehicle’s owner’s manual for reference to the deployment area of the frontal airbags.

Before installing

• Consult with your nearest dealer if installation requires drilling holes or other modifications of the vehicle.
• Before making a final installation of this product, temporarily connect the wiring to confirm that the connections are correct and the system works properly.

Installation notes

• Do not install this product in places subject to high temperatures or humidity, such as:

  • Places close to a heater, vent or air conditioner.
  • Places exposed to direct sunlight, such as on top of the dashboard.
  • Places that may be exposed to rain, such as close to the door or on the vehicle’s floor.

• Install this product horizontally on a surface within 0 to 60 degrees tolerance.

• When installing, to ensure proper heat dispersal when using this unit, make sure you leave ample space behind the rear panel and wrap any loose cables so they are not blocking the vents.

Before installing this product

1. Remove the trim ring.
   Extend top and bottom of the trim ring outwards to remove the trim ring.

2.  Trim ring

3. Remove the holder.
   Loosen the screws to remove the holder.

4.  Holder

5. Screw

Installation with the holder

1. Install the holder into the dashboard.
2. Secure the mounting sleeve by using a screwdriver to bend the metal tabs (90°) into place.
3. Install this product and fasten the screws.
4. Dashboard
5. Attach the trim ring.
6.  Trim ring

Installation using the screw holes on the side of this product

1.  Remove the side brackets.
2.  Screw for fixing the side bracket
3. Side bracket
4. Fastening this product to the factory radio-mounting bracket.
   Position this product so that its screw holes are aligned with the screw holes of the bracket, and tighten the screws at two locations on each side.

TIP
The amount of this unit’s protrusion from the dashboard/console can be adjusted by shifting the position of the screw hole of this unit to the factory radio-mounting bracket.

1.  Factory radio-mounting bracket If the pawl interferes with installation, you may bend it down out of the way.
2. Dashboard or console
3. Flush surface screw
4. Be sure to use the screws supplied with this product.

Installing the GPS aerial

CAUTION
Do not cut the GPS aerial lead to shorten it or use an extension to make it longer. Altering the aerial cable could result in a short circuit or malfunction and permanent damage to this product.

Installation notes

• The aerial should be installed on a level surface where radio waves will be blocked as little as possible. Radio waves cannot be received by the aerial if reception from the satellite is blocked.

1. Dashboard
2. Rear shelf

• Take care not to pull the aerial lead when removing the GPS aerial. The lead may become detached.
• Do not paint the GPS aerial, as this may affect its performance.

When installing the aerial inside the vehicle (on the dashboard or rear shelf)

WARNING
Do not install the GPS aerial over any sensors or vents on the dashboard of the vehicle, as doing so may interfere with the proper functioning of such sensors or vents and may compromise the ability of the GPS aerial to properly and securely affix to the dashboard.

1.  GPS aerial
2. Double-sided tape
3. Clamps
   Use clamps to secure the lead where necessary inside the vehicle.

NOTES

• Affix the GPS aerial on the surface as level as possible where the GPS aerial faces the window.
• Some models use window glass that does not allow signals from GPS satellites to pass through. On such models, install the GPS aerial on the outside of the vehicle.

Installing the microphone

• Install the microphone in a place where its direction and distance from the driver make it easiest to pick up the driver’s voice.
• Be sure to turn off (ACC OFF) the product before connecting the microphone.
• Depending on the vehicle model, the microphone cable length may be too short when you mount the microphone on the sun visor. In such cases, install the microphone on the steering column. Mounting on the sun visor

1. Fit the microphone lead into the groove.
2. Microphone lead
3. Groove
4. Attach the microphone clip to the sun visor.
5. Microphone clip
6. Clamps
   Use separately sold clamps to secure the lead where necessary inside the vehicle.

Install the microphone on the sun visor when it is in the up position. It cannot recognize the driver’s voice if the sun visor is in the down position.

Installation on the steering column

1. Detach the microphone base from the microphone clip by sliding the microphone base while pressing the tab.
2. Tab
3. Microphone base
4. Mount the microphone on the steering column
5. Double-sided tape
6. Clamps
   Use separately sold clamps to secure the lead where necessary inside the vehicle.

NOTE
Install the microphone on the steering column, keeping it away from the steering wheel

Adjusting the microphone angle

The microphone angle can be adjusted.

PIONEER CORPORATION
28-8, Honkomagome 2-chome, Bunkyo-ku, Tokyo 113-0021, Japan

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>