APS IB-P101C 6 Inch Aluminum Running Boards Nerf Bars Installation Guide

June 1, 2024
APS

APS IB-P101C 6 Inch Aluminum Running Boards Nerf Bars Installation

Specifications

  • Product Name: Driver Side Step Bar
  • Mounting Type : Rocker Panel Mount
  • Installation : No drilling required
  • Part Number: IB-P101C&J

Product Usage Instructions

  1. Driver Side Front Mounting
    Start installation from the Driver Side Front of the vehicle. Remove the factory hex bolts or plastic plugs from the threaded holes at the bottom of the body panel.

  2. Driver Front Mounting Bracket Installation
    Select the Driver Front Mounting Bracket and line up the mounting holes with the threaded holes on the body panel. Bolt the bracket to the vehicle using the included hardware. Do not fully tighten at this time.

  3. Driver Side Center & Rear Mounting
    Move to the Driver Side Center & Rear Mounting Locations and repeat the steps to bolt the Driver Center/Rear Mounting Brackets to the factory threaded holes. Do not fully tighten hardware at this time.

  4. Step Bar Installation
    Once all Driver side mounting brackets are installed, proceed to Step Bar installation. Install sliders onto the Step Bar and attach it to the installed mounting brackets. Secure the Step Bar using the provided hardware. Do not fully tighten at this time.

Note: The Sliders are packed with the Mounting Brackets.

Level and adjust the Step Bar and fully tighten all hardware. Repeat these steps for the other side Step Bar installation. The installation is now completed!

READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.

  • ROCKER PANEL MOUNT
  • O DRILLING REQUIRED

PART#: IB-P101C &J

PART LIST

APS IB-P101C 6 Inch-Aluminum-Running-Boards-Nerf-Bars-Installation-fig-
\(2\)APS IB-P101C 6
Inch-Aluminum-Running-Boards-Nerf-Bars-Installation-fig-
\(3\)

Installation

STEP 1
Start installation from the Driver Side Front of the vehicle. Remove the (2) factory hex bolts or plastic plugs from the threaded holes at the bottom of the body panel, (Figs 1 & 2).

APS IB-P101C 6 Inch-Aluminum-Running-Boards-Nerf-Bars-Installation-fig-
\(4\)

STEP 2
Select (1) Driver Front Mounting Bracket. Line up the mounting holes of the Bracket with the threaded holes on the body panel. Bolt the Driver Front Mounting Bracket to the vehicle using the included (2) M8Χ1.25-40mm Hex Bolts, (2) M8 Lock Washers and (2) M8 Large Flat Washers, (Fig 3). Do not fully tighten hardware at this time.

STEP 3
Move to the Driver Side Center & Rear Mounting Locations, (Fig 4). Repeat Steps 1-2 to bolt the Driver Center/Rear Mounting Brackets to the factory threaded holes. Do not fully tighten hardware at this time.

STEP 4
Once all (3) Driver side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 5 & 6)

  1. Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;
  2. Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider.
  3. Slide the Slider (with carriage bolts) to the Step Bar.
  4. Repeat to install the other (2) sliders to the step bar.
  5. Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brack-ets. Secure the Step Bar to the installed Brackets by using (6) M8 Large Flat Washers and (6) M8 Nylon Lock Nuts and (3) Sliders, (Fig 6). Do not fully tighten hardware at this time.

Note : The Sliders are packed with the Mounting Brackets.

  • Level and adjust the Step Bar and fully tighten all hardware.
  • Repeat Steps 1-4 for the other side Step Bar installation. The installation is completed!!!

Attention

  • Do periodic inspections to the installation to make sure that all hardware is secure and tight.
  • In order to protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.

APS IB-P101C 6 Inch-Aluminum-Running-Boards-Nerf-Bars-Installation-fig-
\(7\)

Customer Support: info@iboardauto.com

FAQ

Q: Do I need any special tools for installation?
A: No special tools are required. All necessary hardware is included in Hardware Packages A and B.

Q: Can I install this product alone?
A: While assistance is recommended, one person can install this product following the provided instructions carefully.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

APS User Manuals

Related Manuals