APS WB-CS197BD Black OE Style Nerf Bars Running Boards Instruction Manual

APS WB-CS197BD Black OE Style Nerf Bars Running Boards

Product Information

Specifications

• Product Name: S6 Running Board
• Compatible Vehicles: 2015-2024 Chevy Colorado/GMC Canyon Crew Cab
• Part Numbers: WB-CS197BD, WB-CS197SD, HW-WB-CS197
• Parts Included:
  • 1 Driver/left side Running Board
  • 1 Passenger/right side Running Board
  • 4 Front and Center Mounting Brackets
  • 1 Driver/left side Rear Mounting Bracket
  • 1 Passenger/right side Rear Mounting Bracket
  • 6 8-1.25mm x 35mm Double Bolt Plates
  • 12 8-1.25mm x 25mm Hex Bolts
  • 12 8mm U Clips
  • 24 8mm x 24mm x 2mm Flat Washers
  • 12 8mm Lock Washers
  • 12 8-1.25mm Nylon Lock Nuts

Product Usage Instructions:

1. Remove contents from the box and verify all parts are present.
2. Read the instructions carefully before starting the installation. Assistance is recommended.
3. Start the installation under the driver’s side of the vehicle following the step-by-step procedure detailed in the manual.
4. Repeat the installation steps for the passenger-side Running Board.
5. Do periodic inspections to ensure all hardware is secure and tight.
6. To protect your investment, wax the product after installation. Regular waxing is recommended to add a protective layer over the finish. Use mild soap for cleaning.

PARTS LIST:

PROCEDURE:
REMOVE CONTENTS FROM THE BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.

1. Start the installation under the driver’s side of the vehicle. Locate the front mounting location along the bottom and inner side of the body panel, (Figures 1 & 2). NOTE: It may help to hold a Bracket up in place to help determine the mounting holes to use along the bottom and inner side of the body.

2. Remove rubber plugs from the front location, (Figure 2). Select (2) 8mm Clip Nuts. Slide each Clip Nut into the large hole and over the smaller hole next to it. Line up threaded nut on the Clip Nut with smaller hole in body panel, (Figure 3).

3. Select (1) Front/Center Mounting Bracket, (Figure 4). Attach the Bracket to the (2) Clip Nuts with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Figures 4 & 5). Snug but do not fully tighten the hardware.

4. Move to the next mounting location along the body, (Figures 1 & 2). Repeat Steps 1—3 to install (1) Front/Center Mounting Bracket in the center location, (Figure 5).

5. Next, locate the rear mounting location toward the back of the cab, (Figures 1 & 6). Repeat Steps 1—3 to install the driver side Rear Mounting Bracket in the rear location, (Figure 7). Use the illustration above to help determine the correct Bracket.

6. Once all (3) Brackets have been fully installed, select the Driver/left side Running Board. NOTE: The front stepping pad is farther away from the front end of the Driver/left side Running Board. Select (3) 8mm Double Bolt Plates. Insert the Bolt Plates into the channel on the bottom of the Running Board closest to the Brackets, (Figure 8).

7. With assistance, carefully position the Running Board onto the (3) Mounting Brackets. Attach the Running Board to the Mounting Brackets using (6) 8mm Flat Washers and (6) 8mm Nylon Lock Nuts, (Figures 9—11). Do not tighten the hardware.

8. Slide the Running Board in or out as desired.
   IMPORTANT: Do not allow the front of the Running Board to come in contact with front splash guards if equipped. Level and adjust the Running Board as necessary and fully tighten all hardware.

9. Repeat Steps 1—8 for passenger side Running Board installation.

10. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Running Board.

Driver/left Side Installation Pictured

Frequently Asked Questions (FAQ):

Q: Can I install the running boards without assistance?
A: While it’s recommended to have assistance during installation, it is possible to install the running boards alone with proper care and attention to detail.

Q: How often should I wax the product?
A: Regular waxing is recommended to maintain the finish and protect your investment. It is advisable to wax the product after installing and periodically thereafter based on usage and environmental conditions.

Q: Can I use any type of polish or wax for cleaning?
A: Avoid using polishes or waxes that contain abrasives as they could damage the finish of the running boards. Mild soap is recommended for cleaning.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>