APS HW-WB-FT175 Black Blow Molding Style Nerf Bars Running Boards Instruction Manual

: June 1, 2024
: APS

Table of Contents

APS HW-WB-FT175 Black Blow Molding Style Nerf Bars Running Boards
Product Information
Product Usage Instructions
PARTS LIST
PROCEDURE
Passenger/right Side Installation Pictured
Read User Manual Online (PDF format)
Download This Manual (PDF format)

APS HW-WB-FT175 Black Blow Molding Style Nerf Bars Running Boards

APS-HW-WB-FT175-Black-Blow-Molding-Style-Nerf-Bars-Running-Boards-
PRODUCT

Product Information

Specifications :

Product Name : P1 Plastic Molded Running Board
Compatibility: 2015-2024 Ford F150 Super Crew Cab /2022-2024F150 Lightning/ 2017-2024 Ford F250/350/450/550 Super Duty Crew Cab
Part Number: HW-WB-FT175

Product Usage Instructions

Parts List

2 x P1 Running Boards
6 x Universal Mounting Brackets (left or right)
18 x 8mm Plastic Washers
18 x 8mm x 24mm x 2mm Washers
18 x 8-1.25mm Nylon Lock Nuts
6 x 6mm Double Bolt Plates
12 x 6mm x 22mm x 2mm Flat Washers
12 x 6mm Lock Washers
12 x 6mm Hex Nuts

Installation Procedure:

Start the installation under the passenger side of the vehicle.
Clean mounting studs with a wire brush to remove paint and debris.
Slide Plastic Washers over factory mounting studs.
Attach Mounting Brackets using flat washers and nylon lock nuts.
Install the Running Board on top of the Brackets using Double Bolt Plates.
Secure the Running Board to Brackets with flat washers, lock washers, and hex nuts.
Adjust the Running Board as necessary and tighten all hardware.
Repeat the steps for the driver-side installation.

Cleaning Instructions:

To clean the Running Board, use mild soap. Avoid using polish or wax with abrasives that could damage the finish.

Maintenance:

Periodically inspect the installation to ensure all hardware is secure and tight.

FAQ

Q: Can these running boards be used on other vehicle models?
- A : These running boards are specifically designed for the mentioned Ford vehicle models and may not be suitable for other models.
Q: How do I know if I have installed the running boards correctly?
- A : Proper installation involves securely attaching the brackets, aligning the running board, and tightening all hardware. Refer to the installation instructions for detailed guidance.

PARTS LIST

APS-HW-WB-FT175-Black-Blow-Molding-Style-Nerf-Bars-Running-Boards-
PRODUCT

PROCEDURE

REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.

Start the installation under the passenger side of the vehicle. Locate the front factory running board mounting location along the inner side of the body, (Figure 1). IMPORTANT: Clean mounting studs with wire brush to remove paint and debris.
Slide (1) Plastic Washer over each of the (3) factory mounting studs in the body panel,
(Figures 2 & 3). IMPORTANT: The Plastic Washers are designed to prevent corrosion between the aluminum body panel and the steel mounting brackets. Do not install the Brackets without the Plastic Washers.
Select (1) Mounting Bracket. NOTE: All (6) Brackets are universal and will fit left or right side. Attach the Mounting Bracket to the (3) factory studs with (3) 8mm Flat Washers and (3) 8mm Nylon Lock Nuts, (Figures 4 & 5). Leave brackets loose at this time.
Repeat Steps 1—3 to install the center and rear passenger side Brackets, (Figure 5).
Carefully unwrap and select (1) Running Board. Place the Running Board on top of the Brackets. Locate the channels in the bottom of the Running Board. Select (3) 6mm Double Bolt Plates, (Figure 6). Insert the Bolt Plates into the channels in the bottom of the Running Board closest to the Brackets, (Figure 7). Lift the Running Board up and guide the studs through the Brackets.
Attach the Running Board to the Brackets with (6) 6mm Flat Washers, (6) 6mm Lock Washers and (6) 6mm Hex Nuts, (Figure 8). NOTE: The Running Board is designed to fit close to the vehicle. It may be necessary to loosen the Bracket hardware slightly and tilt the Brackets downward to insert the Running Board between the Brackets and the body.
Level and adjust the Running Board as necessary and fully tighten all hardware.
Repeat Steps 1—7 for the driver side Running Board installation.
Do periodic inspections to the installation to make sure that all hardware is secure and tight.

To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used also to clean the Running Board.