APS IB-298C and H Running Boards 5 inches Matte Black Instruction Manual
- May 15, 2024
- APS
Table of Contents
PS IB-298C and H Running Boards 5 inches Matte Black Instruction Manual
IB-358C Black 6 inches 304 Stainless Steel Running Boards Nerf Bars Side
Steps
Scan for Installation Video
https://www.iboardauto.com/iboard-videos/
READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS
FROM BOX AND VERIFY ALL PARTS ARE PRESENT.
ASSISTANCE IS RECOMMENDED.
ROCKER PANEL MOUNT
NO DRILLING REQUIRED
Fastener Size | Tightening Torque (ft-lbs) | Required |
---|---|---|
6mm | 7-Jun | X |
8mm | 16-18 | √ |
10mm | 31-32 | X |
12mm | 56-58 | X |
14mm | 92-94 | X |
PART LIST
Hardware Package A (For Bracket Installation)
Item | QTY | Description | Item | QTY | Description |
---|---|---|---|---|---|
1# | 8 | M8X1.25-30mm Hex Bolts | 3# | 8 | M8 Lock Washers |
2# | 8 | M8 Large Flat Washers |
Hardware Package B (For Stainless Steel Step Bar Installation)
Item | QTY | Description | Item | QTY | Description |
---|---|---|---|---|---|
1# | 8 | M8X1.25-35mm Carriage Bolts | 3# | 8 | M8 Nylon Lock Nuts |
2# | 8 | M8 Large Flat Washers | 4# | 4 | Sliders (Packed with Step Bars) |
STEP 1
Start installation from the driver side front of the vehicle. Remove the existing (2) factory bolts, (or plastic plugs) (Fig 1).
STEP 2
Select and attach the Driver Front Mounting Bracket (DFM). to the vehicle with
(2) M8x1.25-30mm Hex Bolts, (2) M8 Lock Washers and (2) M8 Large Flat Washers,
(Fig 2). Do not fully tighten hardware at this time.
(Fig 1) Driver Side Front Mounting Location
(Fig 2) Driver Front Mounting Bracket Installation
STEP 3
Move to the driver side rear mounting location, (Fig 3). Repeat Steps 1 – 2
for Driver Rear Mounting Bracket (DRM) installation, (Fig 4).
Do not fully tighten hardware at this time.
(Fig 3) Driver Side Rear Mounting Location
(Fig 4) Driver Rear Mounting Bracket Installation
STEP 4
Once all (2) Driver side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 5&6)
- Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;
- Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider.
- Slide the Slider (with carriage bolts) to the Step Bar.
- Repeat to install the other (1) slider to the step bar.
-
-
- Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brackets.
Secure the Step Bar to the installed Brackets by using (4) M8 Large Flat Washers and (4) M8 Nylon Lock Nuts and (2) Sliders, (Fig 6).
- Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brackets.
-
Do not fully tighten hardware at this time.
Note : The Sliders are packed with the Step Bars.
Level and adjust the Step Bar and fully tighten all hardware.
Repeat Steps 1-4 for the other side Step Bar installation.
The installation is completed!!!
Attention
Do periodic inspections to the installation to make sure that all hardware is
secure and tight.
In order to protect your bars/boards, please use mild soap/non-abrasive
products for cleaning only.
Rev. 20230301
Customer Support: info@iboardauto.com
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>