APS IA-S189H 6.5in Side Armor Stainless Steel Running Boards Instruction Manual
- May 15, 2024
- APS
Table of Contents
APS IA-S189H 6.5in Side Armor Stainless Steel Running Boards Instruction
Manual
BEFORE INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED. THANK YOU FOR CHOOSING OUR PRODUCT!
*ROCKER PANEL MOUNT
*NO DRILLING / TRIMMING REQUIRED
Torque Value
| Fastener Size | Tightening Torque (ft-lbs) | Required |
|---|---|---|
| 6mm | 6-7 | X |
| 8mm | 16-18 | √ |
| 10mm | 31-32 | X |
| 12mm | 56-58 | X |
| 14mm | 92-94 | X |
PART LIST
**Driver Side Step Bar
**
Front
Passenger Side Step Bar
Hardware Package A (For Bracket Installation)
Item| QTY| Description| Item| QTY| Description
1#| 2| Driver Front & Passenger Rear Mounting Brackets| 4#| 12| M8 Plastic
Washers
2#| 2| Passenger Front & Driver Rear Mounting Brackets| 5#| 12| M8 Large Flat
Washers
3#| 4| U Brackets| 6#| 12| M8 Nylon Lock Nuts
Hardware Package B (For Step Bar Installation)
Item| QTY| Description| Item| QTY| Description
1#| 4| M8X1.25-55mm Carriage Bolts| 3#| 4| M8 Lock Washers
2#| 4| M8 Large Flat Washers| 4#| 4| M8 Hex Nuts
The instruction here is for your reference only. We strongly recommend the professional installer for best result. We are not responsible for any damage caused by the installation.
Installation
STEP 1
Start the installation under the passenger side of the vehicle. Locate the
front factory running board mounting location along the inner side of the
body, (Fig 1).
(Fig 1) Passenger Front Mounting Bracket Location
STEP 2
Slide M8 Plastic Washers over each factory mounting stud in the body panel,
(Fig 2).
IMPORTANT: The Plastic Washers are designed to prevent corrosion between the aluminum body panel and the steel mounting brackets. Do not install the Brackets without th Plastic Washers.
STEP 3
Select Passenger Front Mounting Bracket.
Note: Passenger Front Mounting Bracket and Driver Rear Mounting Bracket are Universal. Attach the Mounting Bracket to the (3) factory studs with (3) M8 Large Flat Washers and (3) M8X1.25 Nylon Lock Nuts, (Fig 3). Snug but do not fully tighten the hardware.
**(Fig 2) Thread Plastic Washers Onto 3 Mounting Studs. Passenger Side Front Mounting Location
**
(Fig 3) Passenger Front Mounting Bracket Installed
STEP 4
Repeat Steps 1-3 to install the Passenger Rear Mounting Bracket.
STEP 5
Once all (2) passenger side mounting brackets are installed, select and attach
the Passenger Side Step Bar onto the Mounting Brackets with (2) U Brackets,
(2) M8X1.25 55mm Carriage Bolts, (2) M8 Large Flat Washers, (2)M8 Lock Washers
and (2) M8X1.25 Hex Nuts, (Fig 4). Do not fully tighten hardware at this time.
STEP 6
Properly level and adjust the Step Bar and fully tighten all hardware.
STEP 7
Move to the passenger side of the vehicle. Repeat Steps 1-6 to install the
passenger side step bar.
Installation completed.
(Fig 4) Passenger Side Step Bar Installation
NOTE: Torque all M8 X1.25-55mm Carriage Bolts to 16~18 Ib-ft. Don’t over tighten, or the square bars will be damaged by the brackets
Attention
Do periodic inspections to the installation to make sure that all hardware is
secure and tight.
In order to protect your bars/boards, please use mild soap/non-abrasive
products for cleaning only.
Customer Support: info@iarmorauto.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>