smartwares 600076 Outdoor Light with Camera Instruction Manual
- June 10, 2024
- smartwares
Table of Contents
600076 Outdoor Light with Camera
Instruction Manual
CIP39902 | Outdoor Light with Camera
NONREPLACEABLE LIGHT SOURCE
PARTS DESCRIPTION
- LED light
- Microphone
- Lens
- PIR sensor
- Led indicator
- Back plate
- Reset button
- Speaker
- Micro-SD card slot
BEFORE THE FIRST USE
Optional: Inserting a MicroSD card (not included)
- First make sure your camera is not connected to the power source. Insert your Micro-SD card all the way in the MicroSD card slot on the camera. Only use a class 10 MicroSD card (max 128GB).
- A MicroSD card is required for recording footage.
Download the app
- Download the Connected at Home app from the App store or Google Plays tore.
- Alternatively, you can also use the Smart Life app.
INSTALLATION
- Choose a location to place your camera and check if there is a strong 2,4 GHz Wi-fi signal.
- Turn off the power breaker in your fuse box.
- Remove the back plate from the camera by loosening and removing the screws. (D)
- Lead the power cables from the wall through the hole in the back plate.
- Loosen the screws (A) (1) and connect the power cables to the terminal then tighten the screws. (A) (1) Make sure that the cables are installed within the housing. (B) (2)
Note: To prevent damage, before drilling, make sure that there are no wires or pipes located in the wall.
- Drill holes and mount the back plate to the wall using the screws provided. (B)
- Attach the camera to the back plate (C) and fix it using the screws supplied. (D)
- When the camera is installed turn on the power breaker in your fuse box.
- The camera will now start booting. This will take about 1 minute. Wait until the LED indicator flashes red rapidly.
- Open the Connected at Home or Smarties app.
- Follow the on-screen registration process or log in with existing account.
Adding the camera
- Open the App and press “Add device” or the + button to add the camera.
- For Connected at home app choose “Guardian”.
- For Smarties app choose Smart camera (WIFI).
- Click on “Next” on your smartphone then input your Wi-Fi’s password, click “Next” again and follow the instructions in the App.
- Note: Only 2,4 GHz Wi-Fi network is supported.
LIGHT CONTROL VIA THE APP
On/ Off / Brightness
- You can turn the light on and off or adjust the brightness. Open the menu in the App and press ‘Light’ then use the On/Off button.
Activate light when motion is detected
- In the App settings, turn on the PIR and set the Night mode to Auto. When it is dark, the light will go on whenever motion is detected.
- Default – The light will stay on for 60 seconds when motion is detected, you can modify the timing in the settings, go to ‘Light’ → ‘Time delay’.
Timer
- You can have the light go on/off using the timer. Open the app and go to ‘Light’ → ‘Timer’ and press Add.
- Set 2 timers, one for the light to go ON and one for the light to go OFF. You can also set this schedule for certain days.
Two-way Audio
- The camera uses the built-in speaker and microphone for two- way communication via the App.
Optional: You can adjust the horizontal angle of the camera between 0 to 120 degrees using the App. Open the menu in the app, go to “Direction” and use the arrows to set the camera angle.
TRACKING MODE
When the camera detects a movement in tracking mode, it will rotate and follow the movement. To activate the tracking mode, go to Settings in the App and turn on “Motion Tracking”.
TROUBLESHOOTING
Reset
If needed, you can reset your camera by pressing and holding the reset button
for at least 6 seconds.
Note: One device can only be paired with one App account at a time, if
the device has already been paired with another account, then it can’t be
paired to a new account.
- The device can be removed from the app account by deleting it from the app.
Camera LED indicator information
- Solid red light on: Network unstable
- Blinking red light: Wait for network connection.
- Solid blue light on: Camera is working correctly
MORE INFORMATION
For more instructions and information, please visit our website,
www.smartwares.eu and search for “CIP-39902”.
Technical data:
Wireless technology: Wi-Fi
Frequency: 2.4 GHz Max. Radio Transmission Power: 18,50dBm IP65
Power: AC 100~240V
Led light:
Lumen: 1000 3500K 10 Watt RA: <80
Lifetime: 50.000 hours
EU address: artwares® Europe
Swaardvenstraat 65 5048 A Tilburg The Netherlands
UK address: smartcards® Safety and Lighting Ltd.
Meriden House, 6 Great Cornrow Hales Owen,
West Midlands, B63 3AB United Kingdom
www.smartwares.eu
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>