VORTICE 19230 Metal Dry Ultra Auto Hand Dryer Instruction Manual

Instruction booklet METAL DRY
METAL DRY AUTOMATIC
METAL DRY ULTRA A
METAL DRY SUPER

19230 Metal Dry Ultra Auto Hand Dryer

Read the instructions contained in this booklet carefully before using the appliance.
Vortice cannot assume any responsibility for damage to property or personal injury resulting from failure to abide by the instructions given in this booklet. Following these instructions will ensure a long service life and overall electrical and mechanical reliability.
Keep this instruction booklet in a safe place.
Description and use
This automatic or manual hand dryer is designed to dry hands quickly and offer a high level of performance. The unit has an aluminium cover, to prevent damage, which can only be opened with a key and incorporates special protection devices. The outlet nozzle can be oriented at 360° and has internal protection grille.
These features make the unit ideal for use in public areas.
Automatic versions (Metal Dry Automatic, Metal Dry Ultra A and Metal Dry Super) come with an infrared sensor which must be protected from direct sunlight and from intense lighting, particularly when installed outdoors (e.g. camping grounds, building yards, swimming pools, etc)
Caution: this symbol indicates caution messages aimed at avoiding personal injury to the user

• Do not use this appliance for any application other than that stated in this booklet.
• After removing the appliance from its packing, make sure that it is intact: if in doubt consult a qualified professional or Vortice*. Do not leave packing materials within the reach of children.
• Do not operate the appliance in presence of inflammable vapours (alcohol, insecticides, petrol, etc.).
• Do not place any object on the unit.
• The appliance is not intended for use by young children or infirm persons without supervision.
• Young children should be supervised to ensure that they do not play with the appliance.

Precaution: this symbol indicates precautions which should be taken to avoid damage to the product

• Do not make any modifications of any kind to your unit.
• The unit must not be exposed to atmospheric conditions (rain, direct sunlight, etc.).
• Install the unit following these instructions (fig. 3).
• Do not cover or obstruct the unit’s inlet grille or outlet nozzle.
• Site the automatic hand dryer carefully to avoid interference during operation.
• Since the unit is double insulated, it does not need to be earthed. Regularly inspect the unit. Should the unit suffer damage, fail to operate correctly, or if a fault is found, switch off the supply, and contact Vortice*. Always make sure that original Vortice spare parts are used.
• The unit must be installed by a suitably qualified electrician.
• The installation and wiring must conform to current IEE Regulations (UK) local or appropriate regulations (other countries). It is the installer’s responsibility to ensure that the appropriate Building Codes of Practice are adhered to.
• When installing the unit, a double pole isolation isolation switch must be fitted with a minimum contact gap of 3mm.
• Ensure that the main supply is switched off before making any electrical connections or carrying out maintenance or cleaning.
• (or an authorised Service Centre if you are outside the UK-Ireland territory)
  • The rubber grommet in the base of the unit is suitable for supply cables of between ø 7 mm and 14 mm (fig. 6A-7A-6B). Alternatively the rubber grommet can be removed and a rigid tube of ø 16 mm (Helios or equivalent model) can be fitted (fig. 6C).
  • The units have an internal trimmer which can be adjusted as follows
  • On automatic versions, if you want to adjust the sensitivity of the optical sensors (fig. 24-25), you can adjust the trimmer as required. On manual versions you can adjust the trimmer (fig. 26) to vary drying time

Note:

• If the unit overheats, the power supply will automatically cut out, and will only be restored when the temperature drops back to normal levels. If this first cut-off device malfunctions, a second protection device will cut in and turn off the power.
• The automatic versions incorporate anti-vandal devices that disconnect power after 5-10 minutes of continuous operation.
• The automatic versions also incorporate a timeout function that permits you to move away from the hair dryer for between 2 and 5 seconds without the appliance switching off

INSTALLATION

• The mains supply must conform with the specifications shown on the plate A.

TRIMMER ADJUSTMENT

USE

CLEANING

TROUBLESHOOTING

Before requesting technical assistance, try solving the problem by referring to the following troubleshooting check list

the sensor trimmer (Fig. 24-25)
Unit is mounted at wrong height
Will not turn off or does not operate| Direct exposure to sunlight/lights (installation at campsites, swimming pools, etc.)| Install the unit in another position or protect it from light.
Sensitivity too low| Hands held too close to the outlet nozzle| Adjust the sensor trimmer (Fig. 24-25)
Sensor lenses dirty| Clean lenses
Metal Dry
Metal Dry Automatic Metal Dry Ultra A Metal Dry Super| Does not heat up| Heater failure
Check the voltage of the mains| Contact Vortice
Does not operate| Electronic circuit faulty| Adjust the sensor trimmer (Fig. 24-25-26)
Electronic circuit or switch failure| Contact Vortice
Motor failure

• (or an authorised Service Centre, if you are outside the UK-Ireland territory)

Safety warnings

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
These appliances are designed for use in residential and commercial properties.
The appliance must be installed by a professionally qualified electrician.
The electrical system to which the product is connected must be in compliance with applicable regulations. ; ;
An omnipolar switch with a contact opening distance of 3 mm or higher should be provided for installation, enabling complete disconnection under overvoltage category Ill conditions. .
Products equipped with single-phase wiring (M) engines ALWAYS require connection to 220-240V (or only 230V where required) single-phase lines. Any kind of modification shall be considered as product tampering and shall nullify the relative warranty.
Important information concerning the environmentally compatible disposal of the appliance
This product complies with Directive 2012/19/EU on the management of waste electrical and electronic equipment (WEEE).
**** The crossed-out wheeled bin symbol on the appliance indicates that, at the end of its useful life, the product must be taken to a specialised company for transport and treatment. This company will take care of the disposal of the various materials making up the product and their subsequent proper recycling.
Alternatively, the manufacturer of the appliance is obliged to take back the product to be disposed of in exchange for the purchase of an equivalent appliance.

WARRANTY – OTHER COUNTRIES
The consumer has by law, free of charge, the legal guarantee of conformity with the seller, as described in Directive (EU) 2019/771 in force since January 1, 2022. In EU member countries also refer to local regulations.
VORTICE S.p.A. reserves the right to make improvements to products at any time and without prior notice.
VORTICE GROUP COMPANIES

VORTICE S.p.A.
Strada Cerca, 2 – frazione di Zoate
20067 – Tribiano (MI)
Tel. +39 02-90.69.91
ITALY
vortice.com
postvendita@vortice-italy.com| VORTICE INDUSTRIAL Srl
Via B. Brugnoli, 3
37063 – Isola della Scala (VR)
Tel. +39 045 6631042
ITALY
vorticeindustrial.com
info@vorticeindustrial.com
---|---
VORTICE VENTILATION SYSTEM (CHANGZHOU) CO.LTD
Building 19, No.388 West Huanghe Road, Xinbei District,
Changzhou, Jiangsu Province CAP:213000
CHINA
vortice-china.com
vortice@vortice-china.com| VORTICE LIMITED
Beeches House-Eastern Avenue
Burton on Trent – DE 13 0BB
Tel. +44 1283-49.29.49
UNITED KINGDOM
vortice.ltd.uk
sales@vortice.ltd.uk
VORTICE LATAM S.A.
Bodega #6
Zona Franca BES Alajuela – Alajuela 20101
Tel. (+506) 2201 6934
COSTA RICA
vortice-latam.com
info@vortice-latam.com| CASALS VENTILACIÓN INDUSTRIAL IND., S.L.
Ctra. Camprodon, s/n
17860 – Sant Joan de les Abadesses (Girona)
SPAIN
casals.com
ventilacion@casals.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>