FSA 2ALMLPBSC PowerBox SC Alloy Crankset User Manual
- June 5, 2024
- FSA
Table of Contents
WWW.FULLSPEEDAHEAD.COMPowerBox SC Alloy Crankset Installation Instructions
Published – May, 2021. ZSP022.v0 © Full Speed Ahead
Introduction
Congratulations on your Full Speed Ahead product. Please read these instructions and follow them for correct use. Failure to follow the warnings and instructions could result in damage to product not covered under warranty, damage to bicycle; or cause an accident resulting in injury or death. Since specific tools and experience are necessary for proper installation, it is recommended that the product be installed by a qualified bicycle technician. FSA & Vision assumes no responsibility for damages or injury related to improperly installed components.
Warranty
Full Speed Ahead (FSA) warrants all FSA and Vision products to be free from defects in materials or workmanship for a period of two years after original purchase unless otherwise stated in the full warranty policy. The warranty is non-transferable and valid to the original purchaser of the product only. Any attempt to modify the product in any way such as drilling, grinding, and painting will void the warranty. For more information on warranty policy and instructions for completing a warranty claim, check out the Full Warranty Policy found at our website: https://www.fullspeedahead.com/en/technology
Specification
Item Number PowerBox SC
Assembly
1. Remove the 4 screws from the top of the battery cover, and remove the cover from the battery housing.
2. Install supplied 2450 battery with “+” side up. Wait until the LED flashes green and turns off. Proceed to next step.
3. Replace cover onto Pod.
4. Place 4 screws into holes on the cover.
5. Use 1.5mm wrench tighten the screws to a torque 15.3 kgf.cm / 1.5 Nm / 13.3 in.lbs.
Activation
1. Rotate the crank.
2. Pod displays yellow LED light then blue LED light.
3. It is ready to connect to computer.
Calibration
The PowerBox SC was designed and engineered for ease of use and simple set-up utilizing an easy “1-2-3” set-up process:
1. Place the non-drive crank into six o’clock direction.
2. Calibrate via head unit or via phone application.
3. Once the pod flashes blue white light, the PowerBox SC is calibrated
successfully and you are ready to ride.
Note: Before calibrating on each outdoor ride, it is strongly recommended to leave the crank at outdoor temperature for 10 minutes.
LED Indication
Green – High battery
Yellow – Medium battery
Red – Low battery
Blue – Stand by
Bluewhite – Calibration
Clearance between non-drive arm 1.5 – 2.0 mm
Components
Follow the assembly order in the illustration:
(1) 68mm Bottom Bracket Shell (2) Right Crank x1 (3) Wave Spring Washer x1
(4) Left Crank x1 (5) Crank Bolt Assembly for Left crank x1
Crankset Installation
- Ensure the Bottom Bracket Shell (1) is compatible. (Note : Follow the BB installation instruction for BB will be installed).
- Apply a thin layer of grease on the spindle surfaces (2) which contact bearing.
- Insert the drive crank 2 into the right side of BB shell (1).
- Place Wave Washer (3) onto the Spindle. Install Left Crank Arm (4) onto the axle.
- Ensure crank bolt 5 is pre-installed on axle. Using a torque wrench with 10mm allen key tighten the Crank Bolt (5) to 388-418 kgf.cm / 38-41 Nm / 336-363 in.lbs.
Do not tighten crank bolt over 418 kgf.cm / 41 Nm / 363 in.lbs. Try to avoid completely flattening the wave spring washer (3). Clearance between non-drive arm and bearing shield should be 1.5 – 2.0mm. If the clearance is not within 1.5 – 2.0mm after applying correct torque, DO NOT tighten the crank bolt further. Recheck installation procedure and order of assembled parts. Otherwise may cause bolt tighten torque reduced, evevn left crank loose (4) Always use a calibrated torque wrench to tighten crank bolt. Stripping or breakage due to installing without a torque wrench is NOT covered under manufacturing warranty.
Note: After complete crankset installation the initial rotation torque 5 kgf.cm / 0.5 Nm / 4.4 in.lbs (inclusive) is normal and safe to use!
FCC Statement
FCC ID: 2ALMLPBSC
This device complies with Part 15 of the FCC Rules.Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference
that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that changes or modifications not expressly approved by the
part responsible for compliance could void the user’s authority to operate the
equipment.
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
2. For body worn operation, this device has been tested and meets FCC RF
exposure guidelines. When used with an accessory that contains metal may not
ensure compliance with FCC RF exposure guidelines.
IC Statement
IC: 22650-PBSC
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may
cause undesired operation of the device.
Caution: Exposure to Radio Frequency Radiation
1. To comply with the Canadian RF exposure compliance requirements, this
device and its antenna must not be co-located or operating in conjunction with
any other antenna or transmitter.
2. For body worn operation, this device has been tested and meets RF exposure
guidelines when used with an accessory that contains no metal. Use of other
accessories may not ensure compliance with RF exposure guidelines.
NCC
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Contact
If you have questions, please visit our web site technical section: https://www.fullspeedahead.com/en/support or contact:
Full Speed Ahead, USA
12212 Cyrus Way Mukilteo, WA 98275-5702
Tel: 1_425_488_8653 Fax: 1_425_489_1082
Full Speed Ahead, Europe
Via Del Lavoro, 56 20874 Busnago, Milan, Italy
Tel: +39_039_688_5265 Fax: +39_039_682_3336
TH INDUSTRIES / FSA Asia
NO.6, Wu-gong 8th Rd., Wufeng Dist., Taichung City 41353, Taiwan (R.O.C.)
Tel: +886_4_2331_9134 Fax: +886_4_2331_9314
Notes: Specifications of product may be changed or improved for performance. Please refer to website periodically for technical updates and revised instructions. Printed in Taiwan.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>