smartwares HA32S Wireless Alarm System with Telephone Dialling Unit User Manual

smartwares HA32S Wireless Alarm System with Telephone Dialling Units

Instruction

HA3 2 S ALARM SYSTEM W I TH TELEPHONE DI ALER
The HA3 2 S is a simple w ireless security system for houses and apartments. I t can be operated by remote control or the keypad on the central unit. With the built in telephone dialer it gives you a call w hen something happens. I t is also possible to connect extra detectors and remote controls.
PACKAGE CONTENTS ( 1 )

• Central unit with dialer
• 2x Wireless motion detector
•  2x wireless magnetic contact with external magnet
• 2x remote control

PREPARATI ON
Check and pay attention to the following points before installing the central unit and detectors.

• An area with only one entrance door and not fitted with windows can be secured with a magnetic contact on the door, e.g. a garage, a basement or storage area
• For areas which are only accessible via another central area it is usually sufficient to safeguard that central area with a motion detector
• All open areas with multiple access ways can best be protected with a motion detector
• Place the central unit and detectors preferably at least 0.5 meters from metal objects like central heating pipes, water pipes and radiators

INSTALLATI ON AND PROGRAMMI NG CENTRAL UNIT

• Open the battery cover from the central unit and insert 4x AA batteries ensuring correct polarity. Refit the battery cover, and the central unit is ready for use ( 2 )

• Connect the central unit to the analog telephone line ( 3 )

• Remove the mounting cover from the PI R-detector by sliding it down. Insert a flat blade screwdriver into the groove on the rear of the cover. Turn it 90 degrees leftward or rightward to detach the rear cover from the unit. Then fit 3 AA batteries ensuring correct polarity. Keep the PI R-detector open for learning ( 4 )

• Slide down the battery cover from the magnetic contact. Insert 1 CR2032 battery ensuring correct polarity. Also leave it open for learning ( 5 )

•  Open the remote control battery cover by using a flat blade screwdriver, turning the cover to the open position. Insert 1 CR2032 battery and close the cover ( 6 ) .
  Led indication
  When entering 4-digit security code with the fifth m ode key correctly, the alarm will respond with a long beep with the Status LED being on shortly. I f a sequence of incorrect code is entered, the Status LED will flash and beep three times. Three consecutive input errors will disable the keypad for 30 seconds. I f a sequence of incorrect code is entered during siren sound, the Status LED will flash but without beep tone. Three consecutive input errors will disable the keypad until the siren ceases. In the event of a low battery condition, battery LED will be flashing once every 3 seconds until the battery power depletes.
  Learning remote control and detectors

• Set the central unit into learning m ode by using factory standard pincode, 1 2 3 4 followed by * . The status and battery LED will be blinking

• Press and hold the disarm (bottom ) key on the remote control for over 3 seconds. The LED’s will be lit continuously. When learning is ok, the unit will make a beep and LED’s will be turned off

• To learn the magnetic contact, set the central unit in learning m ode again by pressing 1 2 3 4

  •  Both LED’s will be blinking again

• Press and hold the black switch underneath the battery cover for over 3 seconds. The LED’s will be lit continuously. When learning is ok, the unit will m ake a beep and LED’s will be turned off.

• For learning the PI R-detector, again press 1 2 3 4 * .

• Press the Learn button inside the detector for over 3 seconds, correct learning will be conformed by a short beep.

Programming the central unit

• First start by changing the factory default pincode by your personal code. Press 1 2 3 4 followed by 6 , the status and battery LED will be lit continuously. Put in your new code by pressing 4 numbers, followed by 6 . Correct input will result in a beep and the LED’s will be turned off

Note: numbers 0 to 9 can be used repeatedly as digits in your personal code, however the * and # can’t be used.

• Up to 4 telephone numbers can be learned to the unit. To learn a phone number, press your personal code followed by 7 . The maximum allowable length of inputting a set of telephone number is 30 seconds, while both status battery LED will flash as an indication. Press right after the completion of each telephone number. I f the input has been accepted, the alarm will have a long beep and revert to the disarm m ode. Repeat the same step from the beginning to input another telephone number
  During input, any incorrect digit number can be erased by pressing each time. I f a sequence of incorrect telephone number is entered 3 times or failure in entering telephone number within 30 seconds, the status LED will flash and revert to the disarm m ode straight away
  Arm the alarm by pressing 4-digit security code and then 5 m ode key. The Alarm can start to record after a long beep is emitted. The battery LED will illuminate while recording. The maxim um allowable length of recording the alarm message is 6 seconds. After this period, the alarm will beep once to indicate that the recording has stopped. Alternatively, press any key to stop recording before the m ax. 6 seconds is out. Only one alarm message can be recorded.

Clearing the preset telephone number

Arm the alarm by pressing 4-digit security code and then 9 m ode key. The maxim um allowable length of clearing all preset telephone numbers is 15 seconds, while both status LED and LED
will illuminate steadily as an indication.

• * Press 4-digit security code and 9 m ode key again to clear all of the preset telephone numbers.

  • Press 4-digit security code and 4 m ode key to revert to disarm m ode directly.

Setting type of activation
Default setting: duration for alarm 30 seconds and mute 45 seconds. Arm the alarm by pressing 4-digit security code and then 0 1 m ode key. When the alarm is triggered, it will generate a full alarm condition for 30 seconds and be silent for 45 seconds as one cycle. Such a cycle will be repeated 10 times upon each activation. Each cycle, the alarm will dial up one preset phone number and will not hang up the line until every phone number has been dialed three times. There are two other types of activation that can be chosen as follows:

1. Arm the alarm by pressing 4-digit security code and then 0 2 m ode key. When the alarm is triggered, it will be silent for 45 seconds and initiate a full alarm condition for 30 seconds as one cycle. Such a cycle will be repeated 10 times upon each activation. During 45-second silent period, it will start dialing up one preset phone number.
2. Arm the alarm by pressing 4-digit security code and then 0 3 m ode key. When the alarm is triggered, it will not generate a full alarm condition but will dial up each preset phone number 3 times before the alarm stops.

Note: When there is no phone number memorized, no phone number can be dialed upon alarm activation.
No matter what type of activation is set, the alarm always sounds for 30 seconds and is mute for 45 seconds as one cycle. Every time 45-second countdown starts, the alarm will initiate dialing function so as to dial one of the preset phone numbers with 30-second alarm message. This one-way dialer cannot detect whether the recipient pick up the phone or not. After the phone number is dialed for 5 seconds, the alarm message will be sent and played for 30 seconds before hanging up the line automatically. When the next 45-second silent period starts, it will dial up the next phone number. Each preset phone number needs to be dialed 3 times as prerequisite. I f up to four phone numbers were set, the alarm should dial 12 times, but alarm activation is set for 10 times, as a result, no alarm sound will occur for the last two cycles. I f less than four phone numbers have been programmed, the alarm will stop dialing until all of the preset phone numbers have been dialed 3 times, but 10 times alarm activation remains unchanged.

Arm ing the alarm
Both “instant arm ” and “delay arm ” m ode have a 15-second exit delay duration.

1. The alarm will have a 15-second exit delay before the alarm is arm ed. The delay allows time for you to leave the protected area without triggering the alarm . During this 15-second, the alarm will be silent for 10 seconds and beep for a while and status LED will flash as a notification. The alarm will enter instant arm m ode after expiry of 15-second exit delay. When the alarm is activated, it will sound for 30 seconds and be silent for 45 seconds as one cycle. Such a cycle will be repeated for 10 times upon each activation. During the 45-second silent period, if the phone numbers and alarm message have been set, the alarm will dial up one preset phone number by playing the alarm message for 30 seconds in each cycle.
   Note: We would recommend that the alarm m ode is set for chime m ode when you are at home to avoid hearing dam age resulting from frequent activation.

2.  Delay arm m ode: Arm the alarm by pressing 4-digit security code and then 2 m ode keys. The alarm will have a 15-second exit delay. The delay allows time for you to leave the protected area without triggering the alarm . During this 15-second period, the alarm will be silent for 10 seconds and beep for a while and status LED will flash as a notification. The alarm will enter delay arm m ode after expiry of 15-second exit delay. Once the alarm is activated, the Status LED will be on shortly and the alarm won’t sound until a 15-second entry delay expires. When the alarm is activated, it will sound for 30 seconds and be silent for 45 seconds as one cycle. Such a cycle will be repeated for 10 times upon each activation. During the 45-second silent period, if the phone numbers and alarm message have been set, the alarm will dial up one preset phone number by playing the alarm message for 30 seconds in each cycle.

Disarm ing the alarm
Disarm the alarm by pressing 4-digit security code and then 4 m ode key.
When the alarm is set in the disarm m ode, any activation or reception of radio signal will be ignored.

Activating the chime
Activate the chime by pressing 4-digit security code and then 3 m ode key. Ding-dong can be heard each time when the alarm is activated.

Deactivating the chime
Deactivate the chime by pressing 4-digit security code and then 4 m ode key.

Setting the key tone
This feature, if enabled, allows the alarm to emit a tone each time the keypad is pressed. Default
setting: ON
Key tone can be heard when initially pressing 4-digit security code and then 8 m ode key. Pressing 4-digit security code and then 8 m ode key will take turns at disabling and enabling the key tone.

MOTION SENSOR WALL SWITCH TRANSMITTER ( 7 )

• * When detecting the presence of moving object within the protected area, the transmitter will emit a trigger radio signal to alarm for activation.

  • The transmitter has two m ode of operation: PI R and switch.
  • When switching to PI R m ode, it can be set to act as a security device by detecting changes in infra-red radiation levels. I f a person moves within or across the device field of vision, a trigger radio signal will be transmitted to alarm to cause full alarm condition in order to frighten intruders away.

Note: The switch m ode is designed for use when a series of our ON/ OFF or Dimm er receiver is im plem ented.

Learning id code ( 8 )
I n the rear case, there is a learn key which is used to em it its I D code to the alarm . Press and hold the learn key m ore than 3 seconds during which Note: The switch m ode is designed for use when a series of our ON/ OFF or Dimm er receiver is im plem ented.

Learning id code ( 8 )
I n the rear case, there is a learn key which is used to em it its I D code to the alarm . Press and hold the learn key m ore than 3 seconds during which green LED will be on steadily before turning off. I f release the learn key before 3 seconds is out, green LED will be turned off.
Choosing a mounting location
The recommended position for a transmitter is mounted at a height of 1.2m . At this height, the transmitter will have a maxim um range of up to 10m with a field of view of 160° . Before selecting a position for transmitter, the following points should be noted:
Settings
When switching to the PI R m ode, the transmitter is set to perform the role of security device which means it keeps detecting anytime and if motion is sensed, a trigger radio signal will be sent only once, to alarm to generate full alarm condition in order to frighten intruders away.

Sensitivity adjustment
In order to provide a best efficiency of the transmitter, it is recommended to test the transmitter with movements from a farthest end of the coverage area at first time of use. I f movements cannot be detected sensitively, sim ply adjust the SENSI TI VI TY level. The detection distance can be adjusted up to 10 meters at the mounting height of 1.2 meters. The detection distance is affected by the ambient temperature. Turn the control knob clockwise to LO position of which detection distance can reach about 4 – 6 meter; whereas turning to HI position is about 10 meter.

Operation
While pressing AUTO/ ON/ OFF button each time, green LED will be on shortly.

Warm – Up
It will take approximately 60 seconds to warm up after batteries have been connected during which green LED flashes continuously.

Low Battery Indication
When the battery level of the transmitter drops to a certain value, red LED will flash once every 30 seconds. When this occurs, replace the batteries as soon as possible.
DOOR/ W I NDOW CONTACT DETECTOR ( 9 )Choosing a mounting location
The recommended position for a transmitter is mounted at a height of 1.2m . At this height, the transmitter will have a maxim um range of up to 10m with a field of view of 160° . Before selecting a position for transmitter, the following points should be noted:
Settings
When switching to the PI R m ode, the transmitter is set to perform the role of security device which means it keeps detecting anytime and if motion is sensed, a trigger radio signal will be sent only once, to alarm to generate full alarm condition in order to frighten intruders away.
Sensitivity adjustment
I n order to provide a best efficiency of the transmitter, it is recommended to test the transmitter with movements from a farthest end of the coverage area at first time of use. I f movements cannot be detected sensitively, sim ply adjust the SENSI TI VI TY level. The detection distance can be adjusted up to 10 meters at the mounting height of 1.2 meters. The detection distance is affected by the ambidentate prelature. Turn the control knob clockwise to LO position of which detection distance can reach about 4 – 6 meter; whereas turning to HI position is about 10 meter.

Operation
While pressing AUTO/ ON/ OFF button each time, green LED will be on shortly.
Warm – Up
It will take approximately 60 seconds to warm up after batteries have been connected during which green LED flashes continuously.
Low Battery Indication
When the battery level of the transmitter drops to a certain value, red LED will flash once every 30 seconds. When this occurs, replace the batteries as soon as possible.

DOOR/ WINDOW CONTACT DETECTOR ( 9 )

• Door/ window contact detectors can be fitted to protect doors or windows. I f the protected doors or windows are opened, a radio signal will be transmitted to the alarm .
•  Before fixing the detector to a metal door/ window check the radio range. I t m ay be necessary to space the magnet/ detector off the metal surface using a plastic or wooden spacer to achieve the necessary radio range.
•  Fix the detector and magnet to the opening using either the double sided tape or screws provided.
• Mount the magnet to the door and the detector to the door frame (or vice versa, if necessary).
• Ensure that the arrows on the magnet and detector are pointing towards each other and that the gap between the detector and the magnet is less than 12mm .

Setting

1. There is an I D code that is fixed ex-factory and cannot be adjusted.
2. Emitting I D code:

• Step 1: Fit the battery.
• Step 2: Set the alarm to the code learning m ode.
• Step 3: Press the tam per switch for m ore than 3 seconds on the detector.
• Step 4: I f the alarm has a long beep, the code learning is successful and can start operating. I f not, it implies that the code learning is failure. – Step 5: Starting from Step 2 to re-try.

Operation

1. Upon opening the battery cover, the tam per switch will be triggered. A trigger radio signal will be em itted to the alarm imm ediately.
2. The alarm will sound for 30 seconds and be silent for 45 seconds as a cycle. Such a cycle will be repeated for 10 times, of which duration takes about 12-13 minutes.
3. Separating the magnet from the detector, a radio signal will be emitted to the alarm for chime alert or alarm .
4. indication of LED represents the following status:

Installation

1. Choose a position to drill a hole, insert the plastic wall plug and fix a screw on the wall. Hang up the detector on the screw.
2. Knock out the groove adjacent to the battery compartment and insert the screw to fix the detector on the wall.

REMOTE TRANSMITTER

Emitting ID Code
Pressing the button for 3 seconds will emit the ID code to the alarm , subject to house code  slide switch being set at the right position.

Operation ( 10 )

(* ) = press and hold for 3 seconds

TIPS

• The transmission distance decreases when the signal has to pass through floors or walls
• After removing the batteries, the circuitry will retain residual current. I n order to speed up the consumption of residual current, pressing any keypad for at least 10 seconds is of great importance before refitting the batteries
• A magnetic contact is also perfectly usable for safeguarding cupboards and/ or display cabinets Never place a motion detector directly opposite a window and avoid direct (sun) light on the detector screen (also think of mirrors, etc)
• Avoid installing detectors in places where excessive vibrations m ight take place.

PRODUCT GUARANTEE

This product has factory warranty according to EU regulations. Guarantee lasts for the number of years shown on the packaging, starting from the date of purchase. Keep the receipt – proof of purchase is required in order to rely on guarantee. In the case of problem s, please contact with the store where you purchased the product. For further product information call to our Hotline or visit our website: www.sm artwares.eu . You can also register your product there.

DISPOSAL

Correct Disposal of This Product ( Waste Electrical & Electronic Equipment) ( Applicable in the European Union and other European countries with separate collection system s)posed with other household wastes at the end of its working life. To prevent possible harm -to the environm ent or hum an health from uncontrolled waste disposal, please separate
this from other types of wastes and recycle it responsibly to promote the sustainable reuse -of material resources. Household users should contact either the retailer where they  this item or environmentally safe recycling. Business users should contact their supplier and check the term s and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

• Always throw empty batteries to the battery recycling bin.
• I f the battery is built- in inside the product, open the product and remove the battery.

MAINTENANCE

The devices are maintenance free, so never open them . The guarantee
becomes void when you open the appliance. Only clean the outside of the devices with a soft, dry cloth or a brush. Prior to cleaning, remove the devices from all voltage sources. Do not use any carboxylic cleaning agents or petrol, alcohol or similar. These attack the surfaces of the devices. Besides, the vapors are hazardous to your health and explosive. Do not use any sharp edged tools, screw drivers, metal brushes or similar for cleaning. Warning: Protect the battery against fire, too much heat and sunshine

SAFETY

• Make sure that all electric connections and connection cables meet the pertaining regulations and are in conformity with the operating instructions.
• Do not overload electrical outlets or extension cords, fire or electric shocks can be the result Please contact an expert in case you have any doubts about the m ode of operation, the safety or connecting the appliances.
• Keep all parts away from young children’s reach
• Do not store this item on wet, very cold or warm places, this can dam age the electronic circuit boards.
• Avoid dropping or shocks, this can dam age the electronic boards
• Never replace dam aged power cables yourself! In such a case, remove them from the net and take the devices to a workshop.
• Repairs or opening of this item m ay only be performed by an authorized workshop.
•  Wireless system s are subject to interference from cordless phones, microwaves, and other wireless devices operating in the 2.4GHz range. Keep the system AT LEAST 10ft away from the devices during installation and operation.
• Do not swallow batteries. Keep batteries out of the reach of children.

References

• wares.eu is available for purchase - Sedo.com
• Welkom bij ELRO | Voor een comfortabele en veilige leefomgeving ELRO
• Smartwares - Alles voor een veilig en een comfortabel huis!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>